Solar Panel Fitting & Mounting Kits

Part No: REN-420421 Mounting - Roof Anchor- Trapezoidals SHORT 400mm RAIL Material saving solar installation on trapezoidal sheet. Without continuous rails. Suitable for maximum 370mm distance between centres of raised trapezoidal ridges.  VERTICAL PV MODULE ORIENTATION PV modules with a frame height of 30 to 50 mm are attached to the MS + P mounting system in portrait (standing) on the trapezoidal sheet. INSTALLATION WITHOUT PILOT DRILLING Self-tapping screws fix the MS+P PV mounting system directly to the trapezoidal sheet. FOR TRAPEZOIDAL STEEL AND ALUMINUM METAL SHEET Readymade kits are suitable for the installation of PV systems on trapezoidal sheet steel and / or aluminium in various thicknesses. Metasole Portrait kit: consist of Metasole plates and REN-400281 (SW8 6.0x25 E16) screws.     Renusol mounting equipment must not be used with mounting equipment from other suppliers. Doing so would inevitably void the warranty of the mounting system. Supplier Part No: 420421 Weight: 0.34 kg Length: 0.4 m

Read more less

Part No: REN-420405 Mounting - Roof Anchor- Trapezoidals For use on pitched roofs in landscape with the MetaSole and MS+ range.    Weight: 0.09 kg

Read more less

 Part No: REN-900013-100 Mounting - Wood Screws Wood screw slated tiles: REN-900013, pack of 100   Renusol mounting equipment must not be used with mounting equipment from other suppliers. Doing so would inevitably void the warranty of the mounting system. Supplier Part No: R900013-100 Items in this pack: 100 Weight: 1.145 kg Length: 0.12 m

Read more less

Part No: REN-520075-K Mounting - Flat Roof Trays The ConSole+ provides an angle of 15 degrees. The ConSole+ assembly system is the ideal solution for installing PV modules on flat roofs with a pitch of up to 5 degrees without roof penetration. Most commercially available framed standard PV modules fit the ConSole+. The ConSole+ is weighed down with ballast e.g. gravel, paving slabs, etc... in order to resist the windloads. The necessary weight of the ballast depends on the height of the building, its location and the condition of the ground and the wind and snow loads. Reference values for the necessary ballasts are contained in "Preparing the Assembly - Point 2" in the table of Page 5 of the installation manual. Details: Colour: black Suitable for flat-roof- and ground mounting installations For framed PV-modules Technical Data: Material: HDPE, Aluminium and stainless steel Weight: 7,900 kg Max# module length: 1550-2400 mm Holes gap - width: 895-1014 mm Holes gap - length: 690-1180 mm Other Contents: 1 x 500075 ConSole+ 2 x 400005 ConSole U-Profile 1035 mm 4 x 900027 Hexag# screw DIN933-M6x20 A2-70 4 x 900028 Washer DIN9021-6,4-A2 4 x 900029 Self-locking hexag# nut DIN985-M6-A2 4 x 900106 ConSole Clip 4 x 900115 Hexag# screw DIN7504-ST5,5x25-A2-SW8  Keywords: REN520075K, PV Mounting, Flat Roof Tray Supplier Part No: 520075-K Weight: 8 kg Length: 1.71 m Renusol GmbH based in Cologne (Germany) and is among the fastest  growing businesses on the European market for PV mounting systems. The manufacturer of high-quality mounting solutions is successful with its 4 core mounting options, VarioSole, MetaSole, InterSole and ConSole in many European countries.  

Read more less

Part No: REN-420022 Mounting - Flat Roof Trays Details: ConSole 4.1, 4.2, 5.2, 6.2 and CS+ Compatible with: 520041-K, 520042-K, 520052-K, 520062-K, 520075-K Technical Data: Material: Aluminium and stainless steel Other Contents: 1 x 900115 Hexag. screw DIN7504-ST5,5x25-A2-SW8 4 x 900027 Hexag. screw DIN933-M6x20 A2-70 4 x 900028 Washer DIN9021-6,4-A2 4 x 900029 Self-locking hexag. nut DIN985-M6-A2 4 x 900106 ConSole Clip   Supplier Part No: 420022 Weight: 0.11 kg Length: 1 m

Read more less

Part No: REN-900015-100 Mounting - Fixings Description Technical Data Material Dimensions Weight Anti-slip protection Hexagon head Stainless steel 6 x 20 mm 0,009 kg pack of 100 pcs Keywords: REN900015, Renusol, PV Mounting, Fixings   Supplier Part No: R900015-100 Weight: 0.2 kg Renusol mounting equipment must not be used with mounting equipment from other suppliers. Doing so would inevitably void the warranty of the mounting system.

Read more less

Part No: REN-420181 Mounting - Roof Anchor- Tile & Slates Renusol have created roof hooks specifically for the UK market. This roof hook can be used with Flat and Slate tiles, and is compatible with the VarioSole product range.   Renusol mounting equipment must not be used with mounting equipment from other suppliers. Doing so would inevitably void the warranty of the mounting system. Supplier Part No: 420181 Weight: 0.72 kg

Read more less

Part No: REN-420420 Mounting - Roof Anchor- Trapezoidals SHORT 350mm RAIL Material saving solar installation on trapezoidal sheet. Without continuous rails. Suitable for maximum 320mm distance between centres of raised trapezoidal ridges.  VERTICAL PV MODULE ORIENTATION PV modules with a frame height of 30 to 50 mm are attached to the MS + P mounting system in portrait (standing) on the trapezoidal sheet. INSTALLATION WITHOUT PILOT DRILLING Self-tapping screws fix the MS+P PV mounting system directly to the trapezoidal sheet. FOR TRAPEZOIDAL STEEL AND ALUMINUM METAL SHEET Readymade kits are suitable for the installation of PV systems on trapezoidal sheet steel and / or aluminum in various thicknesses. Metasole Portrait kit: consist of Metasole plates and REN-400281 (SW8 6.0x25 E16) screws.     Renusol mounting equipment must not be used with mounting equipment from other suppliers. Doing so would inevitably void the warranty of the mounting system. Supplier Part No: 420420 Weight: 0.29 kg

Read more less

Part No: REN-420083 Mounting - Cruciforms The Renusol Cross-Rail Connector is used is pairs to attach perpendicular lengths of Renusol rail, or rail to TriSole frames.  A pair of Cross-Rail Connector are attached either side of the upper rail.  The upper rail should always be of 50mm x 37mm type because it has a small ridge along a third face to allow a connector to clamp on, whereas the 41 x 35 does not. Use any of the following rail partnos: (Silver) REN-500502, REN-500505 or (black) REN-400502-B, REN-400505-B.  Technical Data: Dimensions: 35x35x65 Weight: 0.066kg Set: complete pre-assembled set Material: Aluminium; Corrosion resistant steel Certification: TUV ID:48970; MCS012 IK0197 Useable with: VS+ mounting rail 50x37; TS+ Maximum Torque: 12,00 Nm Driver: Hexagon socket 5mm Renusol mounting equipment must not be used with mounting equipment from other suppliers. Doing so would inevitably void the warranty of the mounting system.   Supplier Part No: 420083 Weight: 0.07 kg  

Read more less

 Part No: REN-900036 Mounting - Fixings Keywords: REN900036, Renusol, PV Mounting, Fixings   Renusol mounting equipment must not be used with mounting equipment from other suppliers. Doing so would inevitably void the warranty of the mounting system. Supplier Part No: 900036 Weight: 0.005 kg

Read more less

Part No: REN-900314 Mounting - Flat Roof Socket bolt 6 x 110 mm for use with FS10 system   Renusol mounting equipment must not be used with mounting equipment from other suppliers. Doing so would inevitably void the warranty of the mounting system. Supplier Part No: 900314 Weight: 0.01 kg

Read more less

Part No: REN-420080-B Mounting - Module Clips This innovative masterpiece makes your next PV-project a whole lot easier. The RS1 works as mid- and end clamp. It is heigth adjustable and secures any framed PV panel starting from 30 mm up to 50 mm height. Twisting the RS1‘s head changes the functionality from end- to mid-clamp. Installation and positioning works one handed. At the same time it minimizes needed storage space and saves administrational costs in item management. The RS1 is a real time saver and generates savings over your entire value chain. Technical Data: Dimensions: 35x36.5x60 Weight: 0.083kg Set: complete pre-assembled set Material: Corrosion resistant steel Certification: TUV ID:48970; ETN BT120019; MCS012 IK0197 Module Types: Framed modules only Module Thickness: Between 30.0mm and 50.0mm Maximum Torque: 12,00 Nm Driver: Hexagon socket 5mm   Renusol mounting equipment must not be used with mounting equipment from other suppliers. Doing so would inevitably void the warranty of the mounting system. Supplier Part No: 420080-BE Weight: 0.08 kg Clip Type: 199 Clip H: 60 mm Clip B1: 36.5 mm Clip Colour: Black

Read more less

Part No: SLATE-REN-GEN Mounting - Roof Anchor- Tile & Slates This part is made up of the following items: 1 x Genius Roof - Slate Refit Kit   1 x  Roof hook UK Plain tiles/slates (without wood screw)   Renusol plain roof anchor with Genius Roofing slate refit kit. This part contains:  - 1 x REN-420181 - 1 x GEN-SLATE   Weight: 1.06 kg  

Read more less

 Part No: REN-420080 Mounting - Module Clips This innovative masterpiece makes your next PV-project a whole lot easier. The RS1 works as mid- and end clamp. It is heigth adjustable and secures any framed PV panel starting from 30 mm up to 50 mm height. Twisting the RS1‘s head changes the functionality from end- to mid-clamp. Installation and positioning works one handed. At the same time it minimizes needed storage space and saves administrational costs in item management. The RS1 is a real time saver and generates savings over your entire value chain. Technical Data: Dimensions: 35x36.5x60 Weight: 0.083kg Set: complete pre-assembled set Material: Corrosion resistant steel Certification: TUV ID:48970; ETN BT120019; MCS012 IK0197 Module Types: Framed modules only Module Thickness: Between 30.0mm and 50.0mm Maximum Torque: 12,00 Nm Driver: Hexagon socket 5mm   Renusol mounting equipment must not be used with mounting equipment from other suppliers. Doing so would inevitably void the warranty of the mounting system. Supplier Part No: 420080 Weight: 0.083 kg Clip Type: 199 Clip H: 60 mm Clip B1: 36.5 mm Clip Colour: Silver

Read more less

Part No: SLATE-REN-GEN-NEW Mounting - Roof Anchor- Tile & Slates This part is made up of the following items: 1 x  Roof hook UK Plain tiles/slates (without wood screw)   1 x  Genius Roof - Slate Kit for New Build   Renusol plain roof anchor with Genius Roofing slate refit kit. This part contains:  - 1 x REN-420181 - 1 x GEN-SLATE-NEW   Does not come supplied with Hall Hooks - these might have to be purchased separately.    Weight: 0.96 kg

Read more less

Part No: REN-420423 Mounting - Roof Anchor- Trapezoidals RENUSOL METASOLE+  Rooftop mounting system for trapezoidal and corrugated sheet metal roofs. 125mm long rail, 72mm high.  High Top design raises PV modules higher from the roof surface to increase ventilation and thereby increase the performance of the modules in high temperature applications. 100mm distance to the roof. Short, non-continuous rails lead to material saving solar installation on trapezoidal sheet. Horizontal PV module orientation PV modules with a frame height of 30 to 50 mm are attached to the MS+ HT mounting system in landscape, arranged in columns on the trapezoidal sheet. Installation without pilot drilling - self-tapping screws fix the MS+P PV mounting system directly to the trapezoidal sheet. For trapezoidal steel sheet 0.4-1.25mm thickness and aluminium sheet 0.5-2.00mm thickness Readymade kits suitable for the installation of PV systems on trapezoidal sheet steel and / or aluminium in various thicknesses.  MS+ HT consists of 1 x High Top Mounting Plate and 2 x REN-400281 screws (not sold separately)   Renusol mounting equipment must not be used with mounting equipment from other suppliers. Doing so would inevitably void the warranty of the mounting system.

Read more less

Part No: REN-500411 Mounting - Flat Roof fs10 fs18   Renusol mounting equipment must not be used with mounting equipment from other suppliers. Doing so would inevitably void the warranty of the mounting system. Supplier Part No: 500411 Weight: 0.14 kg

Read more less

Part No: SLATE-REN-GEN-V Mounting - Roof Anchor- Tile & Slates This part is made up of the following items: 1 x  Genius Roof - Slate Refit Kit   1 x  Roof hook UK Plain tiles/slates (without wood screw)   1 x  UK M8 Bracket 90°   Renusol plain roof anchor for vertical mounting rails with Genius Roofing slate refit kit. This part contains:  - 1 x REN-420181 - 1 x GEN-SLATE - 1 x REN-420352   Weight: 1.15 kg

Read more less

Part No: REN-420023 Mounting - Flat Roof Trays The Rear grip clamp for CS (REN-420023) + enables the mounting of solar modules which do not have mounting holes in their frames on the ConSole. PV-Modules without mounting holes or modules which have the module holes on unfavourable positions (e.g. 72 cell modules) can be mounted with this item. This was not possible before with the CS+ solution. Due to that the classical (iconic) system Renusol CS+ can be used in even more cases. Please note this product includes 4 x clips   Supplier Part No: 420023 Weight: 0.15 kg      

Read more less

Part No: REN-400529 Mounting - Mounting Rails VarioSole+ Mounting rail 50 x 37 x 4400mm   Renusol mounting equipment must not be used with mounting equipment from other suppliers. Doing so would inevitably void the warranty of the mounting system. Supplier Part No: 400529 Weight: 3 kg Length: 4.4 m

Read more less

Part No: REN-400288 Mounting - Roof Anchor- Seam Clamps S-5-GXM 10 Mini insert - specifically for use with the S-5-K Grip Mini clamp. Insert options: LYSAGHT KLIP-LOK® 406 McElroy Metal Mirage AEP Span Klip-Rib® Metal Sales Clip-Loc SpeedDeck® SpeedDeck® Safintra Saflok 410 Safintra Saflok 700 Domico Dach® And other similar profiles   Renusol mounting equipment must not be used with mounting equipment from other suppliers. Doing so would inevitably void the warranty of the mounting system. Supplier Part No: 400288 Weight: 0.02 kg

Read more less

Part No: REN-K-GRIP-M-10 Mounting - Roof Anchor- Seam Clamps This part is made up of the following items: 1 x  Renusol Seam Clamp K-Grip Mini (Without Screws)   1 x  Seam clamp GXM 10 Mini Insert ( for K-Grip Mini ) (BTO UK)   Designer note: The Renusol seam clamps are part of the S5 range. You can see more details on manufacturers website.   The S-5-K Grip clamp was specifically developed to fit Klip-Rib® and other bulb snap-together seams. The design utilizes multiple inserts (sold separately) in order to accommodate a variety of bulb snap-together profiles. Each insert has a unique shape that allows for a tight fit and provides increased holding strength over other attachment options. The S-5-K Grip Mini is a bit shorter than the S-5-K Grip and has one base bolt rather than two. The mini is the choice for attaching all kinds of rooftop accessories: signs, walkways, satellite dishes, antennas, rooftop lighting, lightning protection systems, solar arrays, exhaust stack bracing, conduit, condensate lines, mechanical equipment—just about anything!   This is a complete Seam clamp with GX 10 Mini inserts.   UK only: The clamps should meet or exceed the requirements for MCS012 wind uplift values, but since they are not officially MCS012 tested and certified, they should not be used on <50kWp installations.    Weight: 0.13 kg

Read more less

Part No: REN-420401 Mounting - Roof Anchor - Corrugated Corrugated adaptor for Renusol MetaSole. This part allows MetaSole designs to be compatble with corrugated metal roof areas and enables your system to be attached to the roof with self-tapping screws, rather than drilling through the sheet into the substructure with hanger bolts. The added bonus is that no mounting rail is required, which reduces the cost of the mounting dramaticdally. Simple, secure and supremely affordable.  It must be used in conjunction with the MetaSole sheets REN-420402.    Renusol mounting equipment must not be used with mounting equipment from other suppliers. Doing so would inevitably void the warranty of the mounting system. Supplier Part No: 420401 Weight: 0.03 kg

Read more less

Part No: REN-400351 Mounting - Washers 5-mm spacer plate   Renusol mounting equipment must not be used with mounting equipment from other suppliers. Doing so would inevitably void the warranty of the mounting system. Supplier Part No: 400351 Weight: 0.02 kg

Read more less

Part No: REN-420184 Mounting - Roof Anchor- Tile & Slates Renusol have created roof hooks specifically for the UK market. This New roof hook can be used with Slate tiles, where higher snow loads capacity is required, and is compatible with the VarioSole product range. This brand-new version of the roof hook is both thicker and manufactured using stronger steel, offering a higher load capacity for areas with more snow.  This is the UK Plain Tile HL (please note ‘HL’ stands for ‘high load’). The primary benefit of this new hook is the sizeable gain in the load capacity compared to the existing UK plain roof hook: 130% increase for suction loads (wind), 112% increase for pressure loads (self-weight and snow) and 53% more capacity for combined loads.         Supplier Part No: 420184 Weight: 0.6 kg

Read more less

Part No: REN-900025 Mounting - Fixings Details: Haxagon head Flange head with serration Technical Data: Material: stainless steel 1.4301 Weight: 0.027kg     Renusol mounting equipment must not be used with mounting equipment from other suppliers. Doing so would inevitably void the warranty of the mounting system. Supplier Part No: 900025 Weight: 0.02 kg

Read more less

Part No: REN-400523 Mounting - Mounting Rails Renusol Mounting Rail, to be used with the VarioSole product range. Now supplied in longer 2.225m lengths.   Renusol mounting equipment must not be used with mounting equipment from other suppliers. Doing so would inevitably void the warranty of the mounting system. Supplier Part No: 400523 Weight: 1.36 kg Length: 2.22 m

Read more less

Part No: REN-500500 Mounting - Flat Roof Base rail FS10-EW 2260 mm fs10   Renusol mounting equipment must not be used with mounting equipment from other suppliers. Doing so would inevitably void the warranty of the mounting system. Supplier Part No:500500 Weight:2 kg Length:2.26 m

Read more less

Part No: REN-400285 Mounting - Roof Anchor- Seam Clamps GXM 50 Mini insert - specifically for use with the S-5-K Grip Mini clamp. Insert options: LYSAGHT KLIP-LOK Classic® 700 LYSAGHT KLIP-LOK 700 Hi-Strength® Stramit® Speed Deck Ultra® Fielders KingKlip® 700 And other similar profiles   Renusol mounting equipment must not be used with mounting equipment from other suppliers. Doing so would inevitably void the warranty of the mounting system. Supplier Part No:GX50-A-1 Weight:0.01 kg

Read more less

Part No: REN-K-GRIP-M-50 Mounting - Roof Anchor- Seam Clamps This part is made up of the following items: 1 x Renusol Seam Clamp K-Grip Mini (Without Screws)   1 x  Seam Clamp GXM 50 Mini Insert ( for K-Grip Mini ) (BTO UK)   Designer note: The Renusol seam clamps are part of the S5 range. You can see more details on manufacturers website. The S-5-K Grip clamp was specifically developed to fit Klip-Rib® and other bulb snap-together seams. The design utilizes multiple inserts (sold separately) in order to accommodate a variety of bulb snap-together profiles. Each insert has a unique shape that allows for a tight fit and provides increased holding strength over other attachment options. The S-5-K Grip Mini is a bit shorter than the S-5-K Grip and has one base bolt rather than two. The mini is the choice for attaching all kinds of rooftop accessories: signs, walkways, satellite dishes, antennas, rooftop lighting, lightning protection systems, solar arrays, exhaust stack bracing, conduit, condensate lines, mechanical equipment—just about anything!   This is a complete Seam clamp with GX 50 Mini inserts.   UK only: The clamps should meet or exceed the requirements for MCS012 wind uplift values, but since they are not officially MCS012 tested and certified, they should not be used on <50kWp installations.    Weight:0.12 kg

Read more less

Part No: REN-500410 Mounting - Flat Roof fs10 fs18   Renusol mounting equipment must not be used with mounting equipment from other suppliers. Doing so would inevitably void the warranty of the mounting system. Supplier Part No:500410 Weight:0.15 kg

Read more less

Part No: REN-520076 Mounting - Flat Roof Trays Description Material Dimensions Weight Compatible Components To be used on the back row of an installation of ConSole + to reduce the windload and thus ballast required HDPE 1533 x 448 x 361 8,406 kg 520075-K 1 x Streamliner+ 9 x Hexag. screw DIN7504-ST5,5x25-A2-SW8 Keywords: REN520076, Renusol, PV Mounting, Flat Roof Tray   Renusol mounting equipment must not be used with mounting equipment from other suppliers. Doing so would inevitably void the warranty of the mounting system. Supplier Part No:520076 Weight:7.9 kg Length:1.49 m

Read more less

Part No: REN-500453 Mounting - Flat Roof Streamliner for FS10-S This streamliner version is for hoizontal (landscape) module orientation. It supports modules of up to 2100mm in length with 25mm overlap on ridge or 2175mm without 25mm overlap on ridge support.   Renusol mounting equipment must not be used with mounting equipment from other suppliers. Doing so would inevitably void the warranty of the mounting system. Supplier Part No:500453 Weight:3.55 kg Length:2.16 m

Read more less

Part No: REN-500402 Mounting - Flat Roof fs10   Renusol mounting equipment must not be used with mounting equipment from other suppliers. Doing so would inevitably void the warranty of the mounting system. Supplier Part No:500402 Weight:1.2 kg Length:1.64 m

Read more less

Part No: REN-500520 Mounting - Flat Roof Renusol mounting equipment must not be used with mounting equipment from other suppliers. Doing so would inevitably void the warranty of the mounting system. Renusol mounting equipment must not be used with mounting equipment from other suppliers. Doing so would inevitably void the warranty of the mounting system.   Renusol mounting equipment must not be used with mounting equipment from other suppliers. Doing so would inevitably void the warranty of the mounting system. Supplier Part No:500520 Weight:0.4 kg

Read more less

Part No: REN-460001 Mounting - Flat Roof Trays Description Applicational Data Material Dimensions Weight Compatible Components Rail suitable for attachment modules to ConSole ConSole 4.1, 4.2, 5.2 and 6.2 Aluminium 150 x 25 x 12 mm 0,034 kg 400004, 400005, 520041-K, 520042-K, 520052-K, 520062-K,2 x Elongation rail,4 x Hexag. screw DIN933-M6x20 A2-70 4 x Washer DIN9021-6,4-A2 4 x Self-locking hexag. nut DIN985-M6-A2.REN460001, Renusol, PV Mounting, Flat Roof Tray.Renusol mounting equipment must not be used with mounting equipment from other suppliers. Doing so would inevitably void the warranty of the mounting system.Renusol mounting equipment must not be used with mounting equipment from other suppliers. Doing so would inevitably void the warranty of the mounting system. Renusol mounting equipment must not be used with mounting equipment from other suppliers. Doing so would inevitably void the warranty of the mounting system. Supplier Part No:460001 Weight:0.11 kg

Read more less

Part No: REN-520501 Mounting - Flat Roof ECO Ballast set FS (Set) The ballast trays REN-520501 can be optionally added to your design to accommodate a higher amount of ballast, should your particular site need it.    Note: the design tool will not calculate the required ballast weight. Renusol can provide a detailed wind loading report that shows the amount of ballast that is required per module. Please provide them with the installation and site details at: tsuk@renusol.com      This part contains the following:   2x REN-500519 Eco ballast rail 2x REN-900074 Stainless Steel cable ties 1020mm 2x REN-900229 Self drilling screw 4.8 x 19 A2 fs10 fs18   Supplier Part No:520501 Weight:2.01 kg

Read more less

Part No: REN-900183 Mounting - Roof Anchor- Hanger Bolts Technical Data Applicational Data Material Dimensions Weight Compatible Thread length: 125/50; Hexagon socket 5 mm; with building approval Z-14.4 - 555; Setscrew: M10 Clamping range: 60 - 105 mm pre-drilling necessary Stainless steel 8,4 x 181 mm 0,089 kg 420012, 420014, 420130, 420131, 900193, 900205 - 900222 Keywords: REN900183, Renusol, PV Mounting, Roof Anchor- Hanger Bolt   Renusol mounting equipment must not be used with mounting equipment from other suppliers. Doing so would inevitably void the warranty of the mounting system. Supplier Part No:900183 Weight:0.09 kg

Read more less

Part No: REN-920003 Mounting - Roof Anchor- Tile & Slates Technical Data Applicational Data Material Dimensions Weight Compatible Components Space for adjustment vertical: 26,4 mm Max. load: pressure 2300 N, tension 1500 N, shear 1750 N With building approval Z.-14.4 - 515 Roof hook is pre-assembled Frictional connection due to serration 90° twist for vertical mouting Aluminium Stainless steel 215 x 181 x 162 mm 0,479 kg 400081, 400011, 400094, 430009, 490018, 900138, 900163 1 x Roof hook Alu Concrete Basic 90° 1 x Hammerhead bolt M8 x 25 1 x Hexagon Nut w. serration DIN6923 - M8 A2-70   Keywords: REN920003, Renusol, PV Mounting, Roof Anchor- Tile & Slate   Supplier Part No:920003 Weight:0.46 kg

Read more less

Part No: REN-400527 Mounting - Mounting Rails Renusol Mounting Rail, to be used with VarioSole product range.   Supplier Part No:400527 Weight:1.56 kg Length:2.25 m

Read more less

Part No: REN-900013 Mounting - Wood Screws Keywords: REN900013, Renusol, PV Mounting, Wood Screws   Renusol mounting equipment must not be used with mounting equipment from other suppliers. Doing so would inevitably void the warranty of the mounting system. Supplier Part No:900013 Weight:0.01 kg

Read more less

Part No: REN-420563 Mounting - Roof Anchor- Seam Clamps Designer note: The Renusol seam clamps are part of the S5 range. You can see more details on manufacturers website UK only: These clamps are now MCS012 certified with Renusol VariosoleRenusol mounting equipment must not be used with mounting equipment from other suppliers. Doing so would inevitably void the warranty of the mounting system.Renusol mounting equipment must not be used with mounting equipment from other suppliers. Doing so would inevitably void the warranty of the mounting system. UK: This product will be Buy to Order only.   Renusol mounting equipment must not be used with mounting equipment from other suppliers. Doing so would inevitably void the warranty of the mounting system.   Supplier Part No:R420563 Weight:0.19 kg

Read more less

Part No: REN-420012 Mounting - Roof Anchor- Hanger Bolts Technical Data: Material: Aluminium EN-AW-6063 T6 Other Contents: 1 x 400012 Bracket M12 1 x 900007 Hammerhead bolt M8 x 25 1 x 900001 Hexag. nut DIN6923-M8-A2-70 with FL & SZ   Renusol mounting equipment must not be used with mounting equipment from other suppliers. Doing so would inevitably void the warranty of the mounting system. Supplier Part No:420012 Weight:0.11 kg

Read more less

Part No: REN-500400 Mounting - Flat Roof Base rail FS10-S 1389 mm fs10   Renusol mounting equipment must not be used with mounting equipment from other suppliers. Doing so would inevitably void the warranty of the mounting system. Supplier Part No:500400 Weight:1 kg Length:1.39 m

Read more less

Part No: REN-420150 Mounting - Roof Anchor- Tile & Slates Technical Data Applicational Data Material Dimensions Weight Compatible Components Space for adjustment vertical: 37,5 mm Roof hook is pre-assembled Frictional connection due to serration Stainless steel 155 x 180 x 170 mm 0,560 kg 400081, 400011, 400094, 430009, 490018, 900012, 900138, 900145, 900163 1 x Roof hook stainless steel 1 x Hammerhead bolt M8 x 25 1 x Hexagon Nut w. serration DIN6923 - M8 A2-70 Keywords: Roof Anchor- Tile & Slate, Roof Anchor- Tile & Slate, Roof Anchor- Tile & Slate, Roof Anchor- Tile & Slate, Roof Anchor- Tile & Slate, Roof Anchor- Tile & Slate, REN420150, Renusol, PV Mounting, Roof Anchor- Tile & Slate   Renusol mounting equipment must not be used with mounting equipment from other suppliers. Doing so would inevitably void the warranty of the mounting system. Supplier Part No:420150 Weight:0.61 kg

Read more less

Part No: REN-500404 Mounting - Flat Roof Bottom rail connector 150 mm   fs10 fs18   Renusol mounting equipment must not be used with mounting equipment from other suppliers. Doing so would inevitably void the warranty of the mounting system. Supplier Part No:500404 Weight:0.07 kg

Read more less

Part No: REN-900184 Mounting - Roof Anchor- Hanger Bolts Technical Data Applicational Data Material Dimensions Weight Compatible Thread length: 150/50 Hexagon socket 5 mm with building approval Z-14.4 - 555 Setscrew: M10 Clamping range: 80 - 130 mm pre-drilling necessary Stainless steel 8,4 x 206 mm 0,093 kg 420012, 420014, 420130, 420131, 900193, 900205 - 900222 REN900184, Renusol, PV Mounting, Roof Anchor- Hanger Bolt Renusol mounting equipment must not be used with mounting equipment from other suppliers. Doing so would inevitably void the warranty of the mounting system Renusol mounting equipment must not be used with mounting equipment from other suppliers. Doing so would inevitably void the warranty of the mounting system.   Renusol mounting equipment must not be used with mounting equipment from other suppliers. Doing so would inevitably void the warranty of the mounting system. Supplier Part No:900184 Weight:0.1 kg

Read more less

Part No: REN-410557 Mounting - Flat Roof This part is made up of the following items: 1 x  TriSole+ V-frame Assembled   4 x  Renusol Cross rail connector   1 x  TriSole+ Vertical Support 35 degrees   TriSole + Triangle 35° assembled  Renusol mounting equipment must not be used with mounting equipment from other suppliers. Doing so would inevitably void the warranty of the mounting system. Weight:2 kg

Read more less