Welcome to Powerland Renewables!
Register for a Trade Account

Victron

4 products

  • Victron Energy Argofet 100-2 Two Batteries 100A – ARG100201020R-Powerland

    Victron Victron Energy Argofet 100-2 Two Batteries 100A – ARG100201020R

      Similarly to diode battery isolators, FET isolators allow simultaneous charging of two or more batteries from one alternator (or a single output battery charger), without connecting the batteries together. Discharging the accessory battery for example will not result in also discharging the starter battery.   In contrast with diode battery isolators, FET isolators have virtually no voltage loss. Voltage drop is less than 0,02 Volt at low current and averages 0,1 Volt at higher currents.   When using ARGO FET Battery Isolators, there is no need to also increase the output voltage of the alternator. Care should taken however to keep cable lengths short and of sufficient cross section.   Example: When a current of 100 A flows through a cable of 50 mm2 cross section (AWG 0) and 10 m length (30 ft), the voltage drop over the cable will be 0,26 Volt. Similarly a current of 50 A through a cable of 10 mm2 cross section (AWG 7) and 5 m length (15 ft) will result in a voltage drop of 0,35 Volt!   Alternator energize input  Some alternators need DC voltage on the B+ output to start charging. Obviously, DC will be present when the alternator is directly connected to a battery. Inserting a Diode or FET splitter will however prevent any return voltage/current from the batteries to the B+, and the alternator will not start. The new Argofet isolators have a special current limited energize input that will power the B+ when the engine run/stop switch is closed. CLICK HERE FOR SPEC SHEET Brand Victron Energy Manufacturer Part Number ARG100201020R GTIN 8719076019022 Maximum charge current 100A Maximum alternator current 100A Number Of Batteries 2 Connection M8 Bolts Dimensions H65 x W120 x D200mm Weight 1.4Kg Warranty 5 Years

    £67.50 Exc. VAT

    £81.00 Inc. VAT

  • Victron Energy Argofet 100-3 Three Batteries 100A – ARG100301020R-Powerland

    Victron Victron Energy Argofet 100-3 Three Batteries 100A – ARG100301020R

      Similarly to diode battery isolators, FET isolators allow simultaneous charging of two or more batteries from one alternator (or a single output battery charger), without connecting the batteries together. Discharging the accessory battery for example will not result in also discharging the starter battery.   In contrast with diode battery isolators, FET isolators have virtually no voltage loss. Voltage drop is less than 0,02 Volt at low current and averages 0,1 Volt at higher currents.   When using ARGO FET Battery Isolators, there is no need to also increase the output voltage of the alternator. Care should taken however to keep cable lengths short and of sufficient cross section.   Example: When a current of 100 A flows through a cable of 50 mm2 cross section (AWG 0) and 10 m length (30 ft), the voltage drop over the cable will be 0,26 Volt. Similarly a current of 50 A through a cable of 10 mm2 cross section (AWG 7) and 5 m length (15 ft) will result in a voltage drop of 0,35 Volt!   Alternator energize input Some alternators need DC voltage on the B+ output to start charging. Obviously, DC will be present when the alternator is directly connected to a battery. Inserting a Diode or FET splitter will however prevent any return voltage/current from the batteries to the B+, and the alternator will not start. The new Argofet isolators have a special current limited energize input that will power the B+ when the engine run/stop switch is closed. CLICK HERE FOR SPEC SHEET Brand Victron Energy Manufacturer Part Number ARG100301020 Maximum Charge Current (A) 100 Maximum Alternator Current (A) 100 Number Of Batteries 3 Connection M8 Bolts Dimensions H65 x W120 x D200mm Weight (kg) 1.4 Warranty 5 Years

    £77.60 Exc. VAT

    £93.12 Inc. VAT

  • Victron Energy Argofet 200-2 Two batteries 200A – ARG200201020R-Powerland

    Victron Victron Energy Argofet 200-2 Two batteries 200A – ARG200201020R

      Similarly to diode battery isolators, FET isolators allow simultaneous charging of two or more batteries from one alternator (or a single output battery charger), without connecting the batteries together. Discharging the accessory battery for example will not result in also discharging the starter battery.   In contrast with diode battery isolators, FET isolators have virtually no voltage loss. Voltage drop is less than 0,02 Volt at low current and averages 0,1 Volt at higher currents.   When using ARGO FET Battery Isolators, there is no need to also increase the output voltage of the alternator. Care should taken however to keep cable lengths short and of sufficient cross section.   Example: When a current of 100 A flows through a cable of 50 mm2 cross section (AWG 0) and 10 m length (30 ft), the voltage drop over the cable will be 0,26 Volt. Similarly a current of 50 A through a cable of 10 mm2 cross section (AWG 7) and 5 m length (15 ft) will result in a voltage drop of 0,35 Volt!   Alternator energize input Some alternators need DC voltage on the B+ output to start charging. Obviously, DC will be present when the alternator is directly connected to a battery. Inserting a Diode or FET splitter will however prevent any return voltage/current from the batteries to the B+, and the alternator will not start. The new Argofet isolators have a special current limited energize input that will power the B+ when the engine run/stop switch is closed. CLICK HERE FOR SPEC SHEET Brand Victron Energy Manufacturer Part Number ARG200201020R Maximum Charge Current (A) 200 Maximum Alternator Current (A) 200 Number Of Batteries 2 Connection M8 Bolts Dimensions H65 x W120 x D200mm Weight (kg) 1.4 Warranty 5 Years

    £80.30 Exc. VAT

    £96.36 Inc. VAT

  • Victron Energy Argofet 200-3 Three batteries 200A – ARG200301020R-Powerland

    Victron Victron Energy Argofet 200-3 Three batteries 200A – ARG200301020R

    Similarly to diode battery isolators, FET isolators allow simultaneous charging of two or more batteries from one alternator (or a single output battery charger), without connecting the batteries together. Discharging the accessory battery for example will not result in also discharging the starter battery.   In contrast with diode battery isolators, FET isolators have virtually no voltage loss. Voltage drop is less than 0,02 Volt at low current and averages 0,1 Volt at higher currents.   When using ARGO FET Battery Isolators, there is no need to also increase the output voltage of the alternator. Care should taken however to keep cable lengths short and of sufficient cross section.   Example: When a current of 100 A flows through a cable of 50 mm2 cross section (AWG 0) and 10 m length (30 ft), the voltage drop over the cable will be 0,26 Volt. Similarly a current of 50 A through a cable of 10 mm2 cross section (AWG 7) and 5 m length (15 ft) will result in a voltage drop of 0,35 Volt!   Alternator energize input Some alternators need DC voltage on the B+ output to start charging. Obviously, DC will be present when the alternator is directly connected to a battery. Inserting a Diode or FET splitter will however prevent any return voltage/current from the batteries to the B+, and the alternator will not start. The new Argofet isolators have a special current limited energize input that will power the B+ when the engine run/stop switch is closed.  CLICK HERE FOR SPEC SHEET Brand Victron Energy Manufacturer Part Number ARG200301020R Maximum Charge Current (A) 200 Maximum Alternator Current (A) 200 Number Of Batteries 3 Connection M8 Bolts Dimensions H65 x W120 x D200mm Weight (kg) 1.4 Warranty 5 Years

    £94.50 Exc. VAT

    £113.40 Inc. VAT

Powerland is a proud dealer of Victron Energy products, offering a comprehensive selection for off-grid, marine, and mobile applications. From inverters to solar chargers, Victron is known for its reliability and innovation.

Forgot Password


Back to top