Welcome to Powerland Renewables!
Register for a Trade Account

Victron

21 products

  • Victron Energy Pcba For Shunt Bmv 602S/702 - Spr00053 Battery

    Victron Victron Energy PCBA for Shunt BMV 602S/702 - SPR00053

    Replacement PCB only for 500 Amp shunt on BMV 702 & 712 Monitors

    £19.44 Exc. VAT

    £23.33 Inc. VAT

  • Victron Energy Solidswitch 104 - Bms800200104 Battery

    Victron Victron Energy SolidSwitch 104 - BMS800200104

    The SolidSwitch 104 will switch DC loads of up to 70V/4A and can be controlled by a low power digital signal.  The DC load can be resistive, capacitive or inductive (such as the coil of a high-power contactor). The SolidSwitch is not reverse polarity protected and not short circuit proof.

    £27.30 Exc. VAT

    £32.76 Inc. VAT

  • Victron Energy Battery Balancer – BBA000100100-Powerland

    Victron Victron Energy Battery Balancer – BBA000100100

     The Battery Balancer equalizes the state of charge of two series connected 12V batteries, or of several parallel strings of series connected batteries. When the charge voltage of a 24V battery system increases to more than 27V, the Battery Balancer will turn on and compare the voltage over the two series connected batteries. The Battery Balancer will draw a current of up to 1A from the battery (or parallel connected batteries) with the highest voltage. The resulting charge current differential will ensure that all batteries will converge to the same state of charge. If needed, several balancers can be paralleled.A 48V battery bank can be balanced with three Battery Balancers.   Features LED indicators Green: on (battery voltage > 27,3V) Orange: lower battery leg active (deviation > 0,1V) Orange: upper battery leg active (deviation > 0,1V) Red: alarm (deviation > 0,2V). Remains on until the deviation has reduced to less than 0,14V, or until system voltage drops to less than 26,6V. Alarm relay Normally open. The alarm relay closes when the red LED switches on and opens when the red LED switches off Alarm reset Two terminals are available to connect a push button. Interconnecting the two terminals resets the relay. The reset condition will remain active until the alarm is over. Thereafter the relay will close again when a new alarm occurs Even more insight and control with the midpoint monitoring function of the BMV-702 Battery Monitor The BMV-702 measures the midpoint of a string of cells or batteries. It displays the deviation from the ideal midpoint in volts or percent. Separate deviation percentages can be set to trigger a visual/audible alarm and to close a potential free relay contact for remote alarm purposes.  CLICK HERE FOR SPEC SHEET Brand Victron Energy Manufacturer Part Number BBA000100100 Input Voltage Range Up to 18V per battery, 36V total Midpoint deviation to start balancing 50 mV Alarm Relay 60V / 1A normally open Over Temperature Protection Yes Protection Category IP22 Dimensions H100 x W113 x D47mm Weight (kg) 0.4 Warranty 5 Years

    £33.60 Exc. VAT

    £40.32 Inc. VAT

  • Victron Energy SmartShunt 500A/50mV – SHU050150050-Powerland

    Victron Victron Energy SmartShunt 500A/50mV – SHU050150050

     The SmartShunt is an all in one battery monitor, only without a display. Your phone acts as the display. The SmartShunt connects via Bluetooth to the VictronConnect App on your phone (or tablet) and you can conveniently read out all monitored battery parameters, like state of charge, time to go, historical information and much more. Alternatively the SmartShunt can be connected and be read by a GX device. Connection to the SmartShunt is made via a VE.Direct cable. The SmartShunt is a good alternative for a BMV battery monitor, especially for systems where battery monitoring is needed but less wiring and clutter is wanted. The SmartShunt is equipped with Bluetooth, a VE.Direct port and a connection that can be used for: monitoring a second battery, midpoint monitoring or a temperature sensor. Differences compared to BMV712 Battery Monitor No programmable visual and audible alarm. No programmable relay.    CLICK HERE FOR SPEC SHEET Brand Victron Energy Manufacturer Part Number SHU050150050 Supply Voltage Range 6.5-70VDC Battery Capacity 1-9999Ah VE.Direct Communication Port Yes Protection Category IP21 Dimensions H46 x W120 x D54mm Warranty 5 Years

    £63.64 Exc. VAT

    £76.37 Inc. VAT

  • Victron Energy SmartShunt IP65 500A – SHU065150050-Powerland

    Victron Victron Energy SmartShunt IP65 500A – SHU065150050

    The SmartShunt IP65 500A is an all in one battery monitor, only without a display. Your phone acts as the display. The SmartShunt connects via Bluetooth to the VictronConnect app on your phone (or tablet) and you can conveniently read out all monitored battery parameters, like state of charge, time to go, historical information and much more. Alternatively the SmartShunt can be connected and be read by a GX device. Connection to the SmartShunt is made via a VE.Direct cable. The SmartShunt is a good alternative for a BMV battery monitor especially for systems where battery monitoring is needed but less wiring and clutter is wanted.The SmartShunt is equipped with Bluetooth, a VE.Direct port and a connection that can be used for: monitoring a second battery, midpoint monitoring or a temperature sensor.   Differences compared to BMV-712 Battery Monitor– No programmable visual and audible alarm– No programmable relay Why should I monitor my battery with the SmartShunt IP65 500A?Batteries are used in a wide variety of applications, mostly to store energy for later use. But how much energy is stored in the battery? No one can tell by just looking at it. The service life of batteries depends on many factors. Battery life may be shortened by under-charging, over-charging, excessively deep discharges, excessive charge or discharge currents, and by high ambient temperature. Monitoring the battery with a battery monitor will give important feedback to the user so that remedial measures can be taken when necessary. Doing this will extend battery life and the battery monitor will quickly pay for itself.   Brand Victron Energy Manufacturer Part Number SHU065150050 gtin 8719076057895 Protection Category IP65 Bluetooth Enabled Yes Dimensions H46 x W120 x D54mm Warranty 5 Years Country of Manufacture India

    £70.00 Exc. VAT

    £84.00 Inc. VAT

  • Victron Energy BMV-700 Battery Monitor – BAM010700000R-Powerland

    Victron Victron Energy BMV-700 Battery Monitor – BAM010700000R

     The BMV-700 is a high precision battery monitor. The essential function of a battery monitor is to calculate ampere hours consumed and the state of charge of a battery. Ampere hours consumed are calculated by integrating the current flowing in or out of the battery.  Features Battery ‘fuel gauge’, time-to-go indicator, and much more The remaining battery capacity depends on the ampere-hours consumed, discharge current, temperature and the age of the battery. Complex software algorithms are needed to take all these variables into account. Next to the basic display options, such as voltage, current and ampere-hours consumed, the BMV-700 series also displays state of charge, time to go, and power consumption in Watts. Easy to install All electrical connections are to the quick connect PCB on the current shunt. The shunt connects to the monitor with a standard RJ12 telephone cable. Included: RJ 12 cable (10 m) and battery cable with fuse (2 m); no other components needed. Also included are a separate front bezel for a square or round display appearance, a securing ring for the rear mounting and screws for the front mounting.   Standard features Battery voltage, current, power, ampere-hours consumed and state of charge Remaining time at the current rate of discharge Programmable visual and audible alarm Programmable relay, to turn off non critical loads or to run a generator when needed 500 Amp quick connect shunt and connection kit Shunt selection capability up to 10.000 Amps VE.Direct communication port Stores a wide range of historical events, which can be used to evaluate usage patterns and battery health Wide input voltage range: 6,5 – 95V High current measurement resolution: 10 mA (0,01A) Low current consumption: 2,9Ah per month (4mA) @12V and 2,2Ah per month (3mA) @ 24V  CLICK HERE FOR SPEC SHEET Brand Victron Energy Manufacturer Part Number BAM010700000R Supply Voltage Range 6.5-95 VDC Battery Capacity (Ah) 1-9999 Temperature Sensor Optional VE.Direct Communication Port Yes Protection Category IP55 Front Bezel 69 x 69mm Body Diameter & Depth 52 x 31mm Warranty 5 Years

    £77.00 Exc. VAT

    £92.40 Inc. VAT

  • Victron Energy Lynx Power In – LYN020102000-Powerland

    Victron Victron Energy Lynx Power In – LYN020102000

        A modular DC bus bar, used to connect batteries to the Lynx DC distribution system.   The lynx power in module is used to connect batteries via an external fuse. It can be useful if you have multiple parallel strings. Due to the extremely high short circuit current potential of most battery banks, it is suggested to use an external fuse system with an appropriate fault current interruption rating (such as an NH HRC). The Power In contains a negative and positive DC bus-bar with M8 bolts in which to connect batteries cables. It can take cables up to 22 mm in diameter through the bottom entry guides, and no limit via the two side connections.  PLEASE CLICK HERE FOR SPEC SHEET Brand Victron Energy Manufacturer Part Number LYN020102000 Dimensions H282 x W172 x D78mm Weight (kg) 2.1 Warranty 5 Years

    £91.16 Exc. VAT

    £109.39 Inc. VAT

  • Victron Energy BMV-702 Battery Monitor – BAM010702000R-Powerland

    Victron Victron Energy BMV-702 Battery Monitor – BAM010702000R

     The BMV-702 is a high precision battery monitor. The essential function of a battery monitor is to calculate ampere hours consumed and the state of charge of a battery. Ampere hours consumed are calculated by integrating the current flowing in or out of the battery.  Features Battery ‘fuel gauge’, time-to-go indicator, and much more The remaining battery capacity depends on the ampere-hours consumed, discharge current, temperature and the age of the battery. Complex software algorithms are needed to take all these variables into account. Next to the basic display options, such as voltage, current and ampere-hours consumed, the BMV-700 series also displays state of charge, time to go, and power consumption in Watts. Easy to install All electrical connections are to the quick connect PCB on the current shunt. The shunt connects to the monitor with a standard RJ12 telephone cable. Included: RJ 12 cable (10 m) and battery cable with fuse (2 m); no other components needed. Also included are a separate front bezel for a square or round display appearance, a securing ring for the rear mounting and screws for the front mounting. BMV-702 additional features Additional input to measure voltage (of a second battery), temperature or midpoint voltage, and corresponding alarm and relay settings.   Standard features Battery voltage, current, power, ampere-hours consumed and state of charge Remaining time at the current rate of discharge Programmable visual and audible alarm Programmable relay, to turn off non critical loads or to run a generator when needed 500 Amp quick connect shunt and connection kit Shunt selection capability up to 10.000 Amps VE.Direct communication port Stores a wide range of historical events, which can be used to evaluate usage patterns and battery health Wide input voltage range: 6,5 – 95V High current measurement resolution: 10 mA (0,01A) Low current consumption: 2,9Ah per month (4mA) @12V and 2,2Ah per month (3mA) @ 24V  CLICK HERE FOR SPEC SHEET Brand Victron Energy Manufacturer Part Number BAM010702000R Supply Voltage Range 6.5-95 VDC Battery Capacity (Ah) 1-9999 Temperature Sensor Optional VE.Direct Communication Port Yes Protection Category IP55 Front Bezel 69 x 69mm Body Diameter & Depth 52 x 31mm Warranty 5 Years

    £95.90 Exc. VAT

    £115.08 Inc. VAT

  • Victron Energy BMV-702 Black Battery Monitor – BAM010702200R-Powerland

    Victron Victron Energy BMV-702 Black Battery Monitor – BAM010702200R

      The BMV-702 is a high precision battery monitor. The essential function of a battery monitor is to calculate ampere hours consumed and the state of charge of a battery. Ampere hours consumed are calculated by integrating the current flowing in or out of the battery.   Features Battery ‘fuel gauge’, time-to-go indicator, and much more The remaining battery capacity depends on the ampere-hours consumed, discharge current, temperature and the age of the battery. Complex software algorithms are needed to take all these variables into account. Next to the basic display options, such as voltage, current and ampere-hours consumed, the BMV-700 series also displays state of charge, time to go, and power consumption in Watts. Easy to install All electrical connections are to the quick connect PCB on the current shunt. The shunt connects to the monitor with a standard RJ12 telephone cable. Included: RJ 12 cable (10 m) and battery cable with fuse (2 m); no other components needed. Also included are a separate front bezel for a square or round display appearance, a securing ring for the rear mounting and screws for the front mounting. BMV-702 additional features Additional input to measure voltage (of a second battery), temperature or midpoint voltage, and corresponding alarm and relay settings.   Standard features Battery voltage, current, power, ampere-hours consumed and state of charge Remaining time at the current rate of discharge Programmable visual and audible alarm Programmable relay, to turn off non critical loads or to run a generator when needed 500 Amp quick connect shunt and connection kit Shunt selection capability up to 10.000 Amps VE.Direct communication port Stores a wide range of historical events, which can be used to evaluate usage patterns and battery health Wide input voltage range: 6,5 – 95V High current measurement resolution: 10 mA (0,01A) Low current consumption: 2,9Ah per month (4mA) @12V and 2,2Ah per month (3mA) @ 24V  CLICK HERE FOR SPEC SHEET Brand Victron Energy Manufacturer Part Number BAM010702200R Supply Voltage Range 6.5-95 VDC Battery Capacity (Ah) 1-9999 Temperature Sensor Optional VE.Direct Communication Port Yes Protection Category IP55 Front Bezel 69 x 69mm Battery Diameter & Depth 52 x 31mm Warranty 5 Years

    £95.90 Exc. VAT

    £115.08 Inc. VAT

  • Victron Energy SmartShunt 1000A/50mV – SHU050210050-Powerland

    Victron Victron Energy SmartShunt 1000A/50mV – SHU050210050

     The SmartShunt is an all in one battery monitor, only without a display. Your phone acts as the display. The SmartShunt connects via Bluetooth to the VictronConnect App on your phone (or tablet) and you can conveniently read out all monitored battery parameters, like state of charge, time to go, historical information and much more. Alternatively the SmartShunt can be connected and be read by a GX device. Connection to the SmartShunt is made via a VE.Direct cable. The SmartShunt is a good alternative for a BMV battery monitor, especially for systems where battery monitoring is needed but less wiring and clutter is wanted. The SmartShunt is equipped with Bluetooth, a VE.Direct port and a connection that can be used for: monitoring a second battery, midpoint monitoring or a temperature sensor. Differences compared to BMV712 Battery Monitor No programmable visual and audible alarm. No programmable relay.    CLICK HERE FOR SPEC SHEET Brand Victron Energy Manufacturer Part Number SHU050210050 Supply Voltage Range 6.5-70VDC Battery Capacity 1-9999Ah VE.Direct Communication Port Yes Protection Category IP21 Dimensions H68 x W120 x D54mm Warranty 5 Years

    £105.00 Exc. VAT

    £126.00 Inc. VAT

  • Victron Energy BMV-712 Black Smart Battery Monitor – BAM030712200R-Powerland

    Victron Victron Energy BMV-712 Black Smart Battery Monitor – BAM030712200R

    With Bluetooth built-in, the BMV Smart is ready for the Internet of Things (IoT) era. With Bluetooth being implemented in most other Victron Energy products, wireless communication between products will simplify system installation and enhance performance. Features Bluetooth inside With Bluetooth built-in, the BMV Smart is ready for the Internet of Things (IoT) era. With Bluetooth being implemented in most other Victron Energy products, wireless communication between products will simplify system installation and enhance performance. Download the Victron Bluetooth app Use a smartphone or other Bluetooth enabled device to – customize settings, – monitor all important data on single screen, – view historical data, and to – update the software when new features become available. Easy to install All electrical connections are to the quick connect PCB on the current shunt. The shunt connects to the monitor with a standard RJ12 telephone cable. Included: RJ 12 cable (10 m) and battery cable with fuse (2 m); no other components needed. Also included are a separate front bezel for a square or round display appearance, a securing ring for rear mounting and screws for front mounting. Midpoint voltage monitoring One bad cell or one bad battery can destroy a large, expensive battery bank. When batteries are connected in series, a timely warning can be generated by measuring the midpoint voltage. Please see the BMV manual, section 5.2, for more information. We recommend the Battery Balancer (BMS012201000) to maximize service life of series-connected lead-acid batteries. Very low current draw from the battery Current consumption: 0,7Ah per month (1mA) @12V and 0,6Ah per month (0,8mA) @ 24V Especially Li-ion batteries have virtually no capacity left when discharged until low voltage shutdown. After shutdown due to low cell voltage, the capacity reserve of a Li-ion battery is approximately 1Ah per 100Ah battery capacity. The battery will be damaged if the remaining capacity reserve is drawn from the battery. A residual current of 10mA for example may damage a 200Ah battery if the system is left in discharged state during more than 8 days. Bi-stable alarm relay Prevents increased current draw in case of an alarm.    CLICK HERE FOR SPEC SHEET Brand Victron Energy Manufacturer Part Number BAM030712200R Supply Voltage Range 6.5-70 VDC Battery Capacity (Ah) 1-9999 Temperature Sensor Optional VE.Direct Communication Port Yes Protection Category IP55 Front Bezel 69 x 69mm Body Diameter & Depth 52 x 31mm Warranty 5 Years

    £106.64 Exc. VAT

    £127.97 Inc. VAT

  • Victron Energy BMV-712 Smart Battery Monitor – BAM030712000R-Powerland

    Victron Victron Energy BMV-712 Smart Battery Monitor – BAM030712000R

    CLICK HERE FOR SPEC SHEETS With Bluetooth built-in, the BMV Smart is ready for the Internet of Things (IoT) era. With Bluetooth being implemented in most other Victron Energy products, wireless communication between products will simplify system installation and enhance performance.   Features Bluetooth inside With Bluetooth built-in, the BMV Smart is ready for the Internet of Things (IoT) era. With Bluetooth being implemented in most other Victron Energy products, wireless communication between products will simplify system installation and enhance performance. Download the Victron Bluetooth app Use a smartphone or other Bluetooth enabled device to – customize settings, – monitor all important data on single screen, – view historical data, and to – update the software when new features become available. Easy to install All electrical connections are to the quick connect PCB on the current shunt. The shunt connects to the monitor with a standard RJ12 telephone cable. Included: RJ 12 cable (10 m) and battery cable with fuse (2 m); no other components needed. Also included are a separate front bezel for a square or round display appearance, a securing ring for rear mounting and screws for front mounting. Midpoint voltage monitoring One bad cell or one bad battery can destroy a large, expensive battery bank. When batteries are connected in series, a timely warning can be generated by measuring the midpoint voltage. Please see the BMV manual, section 5.2, for more information. We recommend the Battery Balancer (BMS012201000) to maximize service life of series-connected lead-acid batteries. Very low current draw from the battery Current consumption: 0,7Ah per month (1mA) @12V and 0,6Ah per month (0,8mA) @ 24V Especially Li-ion batteries have virtually no capacity left when discharged until low voltage shutdown. After shutdown due to low cell voltage, the capacity reserve of a Li-ion battery is approximately 1Ah per 100Ah battery capacity. The battery will be damaged if the remaining capacity reserve is drawn from the battery. A residual current of 10mA for example may damage a 200Ah battery if the system is left in discharged state during more than 8 days. Bi-stable alarm relay Prevents increased current draw in case of an alarm. Brand Victron Energy Manufacturer Part Number BAM030712000R Supply Voltage Range 6.5-70 VDC Battery Capacity (Ah) 1-9999 Temperature Sensor Optional VE.Direct Communication Port Yes Protection Category IP55 Front Bezel 69 x 69mm Body Diameter & Depth 52 x 31mm Warranty 5 Years Country of Manufacture Malaysia

    £110.60 Exc. VAT

    £132.72 Inc. VAT

  • Victron Energy Lynx Distributor – LYN060102000-Powerland

    Victron Victron Energy Lynx Distributor – LYN060102000

    A modular DC bus bar, with locations for four DC fuses. It will monitor the status of each fuse, and indicate its condition with a LED on the front. Part of the modular Lynx distribution system.   Contains a positive and negative bus-bar and provides a connection for 4 individual DC equipment circuits, loads or DC groups. It has a space for individual DC fuses per DC group. There is an optional feature of an LED for each fuse to indicate if fuse is blown. If you wish to use the fuse indication LEDs on the Lynx Distributor, it also requires a connection to a Lynx Shunt. The Lynx Shunt contains the necessary wide input (8 to 70VDC) power supply to output the required 5V (4,5V-5,5V) power requirement of the Lynx Distributor circuit board. RJ11 fly leads are used to connect the Lynx Shunt to the Distributor. This RJ11 cable is supplied with the Distributor in the box. There are two ports on the Lynx Shunt, and it is possible to use either. When all is OK, only the central LED is green; when a fuse has blown (or is missing) the central and blow fuse circuit LEDs turn red. If you are not using all connection points in your DC distribution, it may be necessary to fit dummy fuses to extinguish the red LEDs. A future upgrade is planned to also send info back to the GX device over the VE-can, but is not yet implemented.   Fuses Uses MEGA fuses. Please note that some MEGA fuses are only rated to 36Volt (suitable for 24V systems), You must use 58/64V rated fuses for 48V systems.  PLEASE CLICK HERE FOR SPEC SHEET Brand Victron Energy Manufacturer Part Number LYN060102000 Dimensions H290 x W170 x D80mm Weight (kg) 2.2 Warranty 5 Years

    £125.47 Exc. VAT

    £150.56 Inc. VAT

  • Victron Energy SmartShunt IP65 1000A – SHU065210050-Powerland

    Victron Victron Energy SmartShunt IP65 1000A – SHU065210050

    The SmartShunt IP65 1000A is an all in one battery monitor, only without a display. Your phone acts as the display. The SmartShunt connects via Bluetooth to the VictronConnect app on your phone (or tablet) and you can conveniently read out all monitored battery parameters, like state of charge, time to go, historical information and much more. Alternatively the SmartShunt can be connected and be read by a GX device. Connection to the SmartShunt is made via a VE.Direct cable. The SmartShunt is a good alternative for a BMV battery monitor, especially for systems where battery monitoring is needed but less wiring and clutter is wanted.The SmartShunt is equipped with Bluetooth, a VE.Direct port and a connection that can be used for: monitoring a second battery, midpoint monitoring or a temperature sensor. Differences compared to BMV-712 Battery Monitor– No programmable visual and audible alarm– No programmable relay Why should I monitor my battery with the SmartShunt IP65 1000A?Batteries are used in a wide variety of applications, mostly to store energy for later use. But how much energy is stored in the battery? No one can tell by just looking at it. The service life of batteries depends on many factors. Battery life may be shortened by under-charging, over-charging, excessively deep discharges, excessive charge or discharge currents, and by high ambient temperature. Monitoring the battery with a battery monitor will give important feedback to the user so that remedial measures can be taken when necessary. Doing this will extend battery life and the battery monitor will quickly pay for itself.   Brand Victron Energy Manufacturer Part Number SHU065210050 gtin 8719076057901 Protection Category IP65 Bluetooth Enabled Yes Dimensions H68 x W168 x D75mm Country of Manufacture India Warranty 5 Years

    £152.50 Exc. VAT

    £183.00 Inc. VAT

  • Victron Energy SmartShunt 2000A/50mV – SHU050220050-Powerland

    Victron Victron Energy SmartShunt 2000A/50mV – SHU050220050

    The SmartShunt is an all in one battery monitor, only without a display. Your phone acts as the display. The SmartShunt connects via Bluetooth to the VictronConnect App on your phone (or tablet) and you can conveniently read out all monitored battery parameters, like state of charge, time to go, historical information and much more. Alternatively the SmartShunt can be connected and be read by a GX device. Connection to the SmartShunt is made via a VE.Direct cable. The SmartShunt is a good alternative for a BMV battery monitor, especially for systems where battery monitoring is needed but less wiring and clutter is wanted. The SmartShunt is equipped with Bluetooth, a VE.Direct port and a connection that can be used for: monitoring a second battery, midpoint monitoring or a temperature sensor. Differences compared to BMV712 Battery Monitor No programmable visual and audible alarm. No programmable relay.    CLICK HERE FOR SPEC SHEET Brand Victron Energy Manufacturer Part Number SHU050220050 Supply Voltage Range 6.5-70VDC Battery Capacity 1-9999Ah VE.Direct Communication Port Yes Protection Category IP21 Dimensions H68 x W120 x D76mm Warranty 5 Years

    £157.50 Exc. VAT

    £189.00 Inc. VAT

  • Victron Energy SmartShunt IP65 2000A – SHU065220050-Powerland

    Victron Victron Energy SmartShunt IP65 2000A – SHU065220050

    The SmartShunt IP65 2000A is an all in one battery monitor, only without a display. Your phone acts as the display. The SmartShunt connects via Bluetooth to the VictronConnect app on your phone (or tablet) and you can conveniently read out all monitored battery parameters, like state of charge, time to go, historical information and much more. Alternatively the SmartShunt can be connected and be read by a GX device. Connection to the SmartShunt is made via a VE.Direct cable. The SmartShunt is a good alternative for a BMV battery monitor, especially for systems where battery monitoring is needed but less wiring and clutter is wanted.The SmartShunt is equipped with Bluetooth, a VE.Direct port and a connection that can be used for: monitoring a second battery, midpoint monitoring or a temperature sensor. Differences compared to BMV-712 Battery Monitor– No programmable visual and audible alarm– No programmable relay Why should I monitor my battery with the SmartShunt IP65 2000A?Batteries are used in a wide variety of applications, mostly to store energy for later use. But how much energy is stored in the battery? No one can tell by just looking at it. The service life of batteries depends on many factors. Battery life may be shortened by under-charging, over-charging, excessively deep discharges, excessive charge or discharge currents, and by high ambient temperature. Monitoring the battery with a battery monitor will give important feedback to the user so that remedial measures can be taken when necessary. Doing this will extend battery life and the battery monitor will quickly pay for itself.   Brand Victron Energy Manufacturer Part Number SHU065220050 gtin 8719076057918 Protection Category IP65 Bluetooth Enabled Yes Dimensions H68 x W168 x D100mm Warranty 5 Years Country of Manufacture India

    £207.50 Exc. VAT

    £249.00 Inc. VAT

  • Victron Energy Lynx Shunt VE.Can – LYN040102100-Powerland

    Victron Victron Energy Lynx Shunt VE.Can – LYN040102100

    The Lynx Shunt VE.Can is an intelligent 1000A shunt with location for a fuse (not included), the built in battery monitor accurately monitors the state of charge of your battery. Use the Color Control GX for reading out the information. Part of the modular Lynx distribution system.  PLEASE CLICK HERE FOR SPEC SHEET Brand Victron Energy Manufacturer Part Number LYN040102100 Dimensions H166.5 x W181.8 x D81mm Weight (kg) 1.4 Warranty 5 Years

    £241.50 Exc. VAT

    £289.80 Inc. VAT

  • Victron Energy BMV-700H Battery Monitor – BAM010700100-Powerland

    Victron Victron Energy BMV-700H Battery Monitor – BAM010700100

    The BMV-700H is a high precision battery monitor. The essential function of a battery monitor is to calculate ampere hours consumed and the state of charge of a battery. Ampere hours consumed are calculated by integrating the current flowing in or out of the battery.   Features Battery ‘fuel gauge’, time-to-go indicator, and much more The remaining battery capacity depends on the ampere-hours consumed, discharge current, temperature and the age of the battery. Complex software algorithms are needed to take all these variables into account. Next to the basic display options, such as voltage, current and ampere-hours consumed, the BMV-700 series also displays state of charge, time to go, and power consumption in Watts. Easy to install All electrical connections are to the quick connect PCB on the current shunt. The shunt connects to the monitor with a standard RJ12 telephone cable. Included: RJ 12 cable (10 m) and battery cable with fuse (2 m); no other components needed. Also included are a separate front bezel for a square or round display appearance, a securing ring for the rear mounting and screws for the front mounting.   Standard features Battery voltage, current, power, ampere-hours consumed and state of charge Remaining time at the current rate of discharge Programmable visual and audible alarm Programmable relay, to turn off non critical loads or to run a generator when needed 500 Amp quick connect shunt and connection kit Shunt selection capability up to 10.000 Amps VE.Direct communication port Stores a wide range of historical events, which can be used to evaluate usage patterns and battery health Wide input voltage range: 6,5 – 95V High current measurement resolution: 10 mA (0,01A) Low current consumption: 2,9Ah per month (4mA) @12V and 2,2Ah per month (3mA) @ 24V  CLICK HERE FOR SPEC SHEET Brand Victron Energy Manufacturer Part Number BAM010700100 Supply Voltage Range 60-385 VDC Battery Capacity (Ah) 1-9999 Temperature Sensor Optional VE.Direct Communication Port Yes Protection Category IP55 Front Bezel 69 x 69mm Body Diameter & Depth 52 x 31mm Warranty 5 Years

    £353.50 Exc. VAT

    £424.20 Inc. VAT

  • Victron Energy BMV-710H Smart Battery Monitor – BAM030710100-Powerland

    Victron Victron Energy BMV-710H Smart Battery Monitor – BAM030710100

    The BMV-710H Smart has Bluetooth built-in and can connect wirelessly to your phone (or tablet) via the VictronConnect App to conveniently read out all monitored battery parameters, like state of charge, time to go, historical information and much more. The BMV-710H Smart is a high precision battery monitor that has been specially designed for systems with a high battery voltage ranging from 60 to 385 Volts.   Features Battery ‘fuel gauge’, time-to-go indicator, and much more The remaining battery capacity depends on the ampere-hours consumed, discharge current, temperature and the age of the battery. Complex software algorithms are needed to take all these variables into account. Next to the basic display options, such as voltage, current and ampere-hours consumed, the BMV-700 series also displays state of charge, time to go, and power consumption in Watts. Bluetooth Smart Use the Bluetooth Smart dongle to monitor your batteries on Apple or Android smartphones, tablets, macbooks and other devices. Easy to install All electrical connections are to the quick connect PCB on the current shunt. The shunt connects to the monitor with a standard RJ12 telephone cable. Included: RJ 12 cable (10 m) and battery cable with fuse (2 m); no other components needed. Also included are a separate front bezel for a square or round display appearance, a securing ring for the rear mounting and screws for the front mounting.   Standard features Battery voltage, current, power, ampere-hours consumed and state of charge Remaining time at the current rate of discharge Programmable visual and audible alarm Programmable relay, to turn off non critical loads or to run a generator when needed 500 Amp quick connect shunt and connection kit Shunt selection capability up to 10.000 Amps VE.Direct communication port Stores a wide range of historical events, which can be used to evaluate usage patterns and battery health Wide input voltage range: 6,5 – 95V High current measurement resolution: 10 mA (0,01A) Low current consumption: 2,9Ah per month (4mA) @12V and 2,2Ah per month (3mA) @ 24V  CLICK HERE FOR SPEC SHEET Brand Victron Energy Manufacturer Part Number BAM030710100 GTIN 8719076049500 Protection Category IP55 VE.Direct Communication Port Yes Front Bezel 69 x 69mm Body Diameter & Depth 52 x 31mm Warranty 5 Years

    £370.30 Exc. VAT

    £444.36 Inc. VAT

  • Victron Energy Lynx Smart BMS 500 – LYN034160200-Powerland

    Victron Victron Energy Lynx Smart BMS 500 – LYN034160200

    The Lynx Smart BMS is a dedicated Battery Management System for Victron Lithium Smart Batteries. There are multiple BMS-es available for our Smart Lithium series of batteries, and the Lynx Smart is the most feature rich and complete option. Its main features are: Built-in 500A contactor, used as a fall-back safety mechanism and also available as a remote controllable main systems switch Battery monitor, indicating state of charge percentage and more data. Pre-alarm signal: provide a warning before the system shuts down due to -for example- a low cell. Bluetooth for use with the VictronConnect App for setup and monitoring. Local and remote monitoring using a Victron GX device, for example the Cerbo GX. The Lynx Smart BMS is part of the modular Lynx Distribution system.  PLEASE CLICK HERE FOR SPEC SHEET Brand Victron Energy Manufacturer Part Number LYN034160200 GTIN 8719076047476 Protection Category IP22 Bluetooth Enabled Yes Dimensions H190 x W180 x D80mm Weight 1.9Kg Warranty 5 Years

    £633.50 Exc. VAT

    £760.20 Inc. VAT

  • Lynx Smart Bms 1000 Battery

    Victron Lynx Smart BMS 1000

    The Lynx Smart BMS is a dedicated Battery Management System for Victron Lithium Smart Batteries. There are multiple BMS-es available for our Smart Lithium series of batteries, and the Lynx Smart is the most feature rich and complete option. Its main features are: Built-in 1000A contactor, used as a fall-back safety mechanism and also available as a remote controllable main systems switch Battery monitor, indicating state of charge percentage and more data. Pre-alarm signal: provide a warning before the system shuts down due to -for example- a low cell. Bluetooth for use with VictronConnect App, for setup and monitoring. Local and remote monitoring using a Victron GX device, for example the Cerbo GX.

    £800.00 Exc. VAT

    £960.00 Inc. VAT

Powerland is a proud dealer of Victron Energy products, offering a comprehensive selection for off-grid, marine, and mobile applications. From inverters to solar chargers, Victron is known for its reliability and innovation.

Forgot Password


Back to top