Victron
Powerland Victron Energy SmartSolar MPPT RS 450/100-Tr – SCC145110410
The SmartSolar MPPT RS solar charge controllers are Victron’s solution for systems with large series connected PV arrays charging 48 V DC battery banks. This product is perfect for large off-grid, and grid connected battery systems. Available in a 5.76kW and 11.52kW model, features include a wide 80-450 VDC operating solar voltage input, independent tracking inputs, full connectivity, isolated PV connections, display screen, fully programmable battery charging parameters and active cooling. The new metal case design and fully covered electrical connections improve the safety and modernise the presentation in line with the latest suite of Victron products. Features Ultra-fast Maximum Power Point Tracking (MPPT) Solar Charge Controller The MPPT RS SmartSolar is a 48V Solar charge controller with up to 450VDC PV input and either 100A, or 200A output. It is used in on-grid and off-grid solar applications where maximum battery charging power is required. Setup and monitor with VictronConnect The SmartSolar RS charge controller can be remotely controlled and configured over Bluetooth via the VictronConnect App. This allows device set-up, management, and at-a-glance information, such as battery voltage and current, PV voltage and current, historical data and trends. Multiple independent MPPT tracking inputs With multiple MPPT trackers, you can optimize your solar panel design for maximum performance for your specific location. Daisy Chain Additional Units The SmartSolar RS charge controller is equipped with VE.Can bus ports. This allows for communication with additional SmartSolar RS & VE.Can MPPT units. The additional units are simply “daisy chained” to each other with an RJ45 cable. When connected to each other, all individual charge controllers, will synchronise their charge stages. They can also send their data, via the same cable, for monitoring to a GX device (such as the Cerbo GX). Isolated PV connections for additional safety Full galvanic isolation between PV and battery connections provide additional overall system safety. Wide MPPT voltage range 80 – 450 VDC PV operating range, with a 120VDC PV startup voltage. Light weight, efficient and quiet Thanks to high frequency technology and a new design this powerful charger weighs only 7.9 kg for the 100A model. In addition to this it has an excellent efficiency, low standby power, and a very quiet operation. Display and Bluetooth The display reads battery, and controller parameters. The parameters can be accessed with a smartphone or other Bluetooth enabled device. In addition, Bluetooth can be used to set up the system and to change settings with VictronConnect. PV Isolation resistance monitoring for peace of mind at higher voltages The MPPT RS continuously monitors the PV array and can detect if there are faults that reduce the isolation of the panels to unsafe levels. VE.Can and VE.Direct port For connection to a GX device for system monitoring, data logging, and remote firmware updates. VE.Can allows for up to 25 units to be connected together in parallel and synchronize their charging. I/O Connections Programmable Relay, temperature sensor, auxiliary, digital input and voltage sensor connections. The remote input can accept the Victron smallBMS, and other BMS with allow-to-charge signal CLICK HERE FOR SPEC SHEET Brand Victron Energy Manufacturer Part Number SCC145110410 GTIN 8719076049319 Battery Voltage 48 V Rated Charge Current 100 A Maximum Charge Power 5,8 kW at 57,6 V Charge Voltage Absorption’ Default setting: 57,6 V (adjustable) Charge Voltage 'Float' Default setting: 55,2 V (adjustable) Programmable Voltage Range Minimum: 36 V, Maximum: 62 V Charge Algorithm Multi-stage adaptive (adjustable) Battery Temperature Sensor Included Maximum efficiency 96% Self-consumption 15 mA Maximum DC PV Voltage 450 V Start-up voltage 120 V MPPT operating voltage range 80 – 450 V Number Of Trackers 2 Max. PV Operational Input Current 18 A per tracker Max. PV Short Circuit Current 20 A per tracker Maximum PV Array Size Per Tracker 7200 Wp (450 V x 20 A) Synchronised Parallel Operation Yes, up to 25 units with VE.Can Programmable Relay Yes Data Communication VE.Direct port, VE.Can port & Bluetooth General Purpose Analogue/Digital In Port Yes, 2x Remote on-off Yes Protection Category IP21 Battery-Connection M8 Bolts Dimensions H400 x W313 x D126mm Weight 7.9Kg Warranty 5 Years
£920.00 Exc. VAT
£1,104.00 Inc. VAT
Powerland Victron Energy Inverter RS 48/6000 230V Smart Solar – PIN482601000
The Inverter RS Smart Solar is a combination of a powerful 48VDC, 6kVA 230VAC inverter and a high voltage, 80-450VDC, 4kW MPPT solar charger. Thanks to its modern design and high frequency technology the inverter only weighs 11kg and has an excellent efficiency, low standby power, and very quiet operation. The inverter is equipped with a display to read out battery, inverter, and solar charger details. These parameters can also be read out via Bluetooth by the VictronConnect app. In addition to this, the inverter has a VE.Can Port for connection to a GX device for system monitoring; and VE.Direct port for connection to a GlobalLink 520. Features Off-Grid solar inverter The Inverter RS Smart Solar 48/6000 is a 48V 6kVA Inverter with 450VDC 4kWp PV input. It is used in off-grid solar applications where AC power is required. Combination of an inverter, bi-directional DC-DC converter and MPPT The inverter produces a perfect sine wave, able to supply high powered appliances. It is supplied by a bi-directional DC-DC converter, that can either charge the battery when excess solar power is available or convert from the battery when it is needed. Wide MPPT voltage range 80 – 450VDC, with a 120VDC PV startup voltage. Light weight, efficient and quiet Thanks to high frequency technology and a new design this powerful inverter weighs only 11kg. In addition to this it has an excellent efficiency, low standby power, and a very quiet operation. Display and Bluetooth The display reads battery, inverter and solar charge controller parameters. The same parameters can be accessed with a smartphone or other Bluetooth enabled device. In addition, Bluetooth can be used to set up the system and to change settings with VictronConnect. VE.Can and VE.Direct port For connection to a GX device for system monitoring, data logging, and remote firmware updates. Built in PV isolator Both parallel PV strings connected to the MC4 plugs can be safely isolated with the large built-in switch on the bottom of the unit. I/O Connections Programmable Relay, temperature sensor and voltage sensor connections. The remote input can also be configured to accept the Victron smallBMS. CLICK HERE FOR SPEC SHEET Brand Victron Energy Manufacturer Part Number PIN482601000 GTIN 8719076048176 DC Input voltage range 38-64V Continuous Output Power at 25°C Increases linearly from 4800W at 46VDC to 5300W at 52VDC Continuous output power at 40°C 4500W Peak power 9kW for 3 seconds Zero load power 20W Maximum DC voltage 450V Nominal DC voltage 300V Start-up voltage 120V MPPT operating voltage range 80-450V Charge voltage absorption (V DC) 57.6V Charge voltage float (V DC) 55.2V Maximum charge current 100A Battery Temperature Sensor Yes Parallel and 3-phase operation No Programmable Relay Yes Data Communications Ports VE.Direct port and VE.Can port Remote on-off Yes Protection Category IP22 Battery-Connection M8 Bolts Dimensions H425 x W440 x D125mm Weight 11Kg Warranty 5 Years
£1,330.00 Exc. VAT
£1,596.00 Inc. VAT
Powerland Victron Energy SmartSolar MPPT RS 450/200-MC4 – SCC145120510
The SmartSolar MPPT RS solar charge controllers are Victron’s solution for systems with large series connected PV arrays charging 48 V DC battery banks. This product is perfect for large off-grid, and grid connected battery systems. Available in a 5.76kW and 11.52kW model, features include a wide 80-450 VDC operating solar voltage input, independent tracking inputs, full connectivity, isolated PV connections, display screen, fully programmable battery charging parameters and active cooling. The new metal case design and fully covered electrical connections improve the safety and modernise the presentation in line with the latest suite of Victron products. Features Ultra-fast Maximum Power Point Tracking (MPPT) Solar Charge Controller The MPPT RS SmartSolar is a 48V Solar charge controller with up to 450VDC PV input and either 100A, or 200A output. It is used in on-grid and off-grid solar applications where maximum battery charging power is required. Setup and monitor with VictronConnect The SmartSolar RS charge controller can be remotely controlled and configured over Bluetooth via the VictronConnect App. This allows device set-up, management, and at-a-glance information, such as battery voltage and current, PV voltage and current, historical data and trends. Multiple independent MPPT tracking inputs With multiple MPPT trackers, you can optimize your solar panel design for maximum performance for your specific location. Daisy Chain Additional Units The SmartSolar RS charge controller is equipped with VE.Can bus ports. This allows for communication with additional SmartSolar RS & VE.Can MPPT units. The additional units are simply “daisy chained” to each other with an RJ45 cable. When connected to each other, all individual charge controllers, will synchronise their charge stages. They can also send their data, via the same cable, for monitoring to a GX device (such as the Cerbo GX). Isolated PV connections for additional safety Full galvanic isolation between PV and battery connections provide additional overall system safety. Wide MPPT voltage range 80 – 450 VDC PV operating range, with a 120VDC PV startup voltage. Light weight, efficient and quiet Thanks to high frequency technology and a new design this powerful charger weighs only 7.9 kg for the 100A model. In addition to this it has an excellent efficiency, low standby power, and a very quiet operation. Display and Bluetooth The display reads battery, and controller parameters. The parameters can be accessed with a smartphone or other Bluetooth enabled device. In addition, Bluetooth can be used to set up the system and to change settings with VictronConnect. PV Isolation resistance monitoring for peace of mind at higher voltages The MPPT RS continuously monitors the PV array and can detect if there are faults that reduce the isolation of the panels to unsafe levels. VE.Can and VE.Direct port For connection to a GX device for system monitoring, data logging, and remote firmware updates. VE.Can allows for up to 25 units to be connected together in parallel and synchronize their charging. I/O Connections Programmable Relay, temperature sensor, auxiliary, digital input and voltage sensor connections. The remote input can accept the Victron smallBMS, and other BMS with allow-to-charge signal CLICK HERE FOR SPEC SHEET gtin 8719076051886 Brand Victron Energy Manufacturer Part Number SCC145120410 Warranty 5 Years Country of Manufacture India Weight (kg) 13.7Kg Programmable Relay Yes Dimensions H487 x W434 x D146mm Battery Voltage 48 V Rated Charge Current 200 A Max. PV Short Circuit Current 20 A per tracker Charge Algorithm Multi-stage adaptive (adjustable) Battery Temperature Sensor Included Remote on-off Yes Battery-Connection M8 Bolts Protection Category IP21 Start-up voltage 120 V MPPT operating voltage range 80 – 450 V Self-consumption 15 mA Maximum efficiency 96% Programmable Voltage Range Minimum: 36 V, Maximum: 62 V Charge Voltage Absorption’ Default setting: 57,6 V (adjustable) Maximum Charge Power 11,5 kW at 57,6 V Charge Voltage Float Default setting: 55,2 V (adjustable) Maximum DC PV Voltage 450 V Number Of Trackers 4 Max. PV Operational Input Current 18 A per tracker Maximum PV Array Size Per Tracker 7200 Wp (450 V x 20 A) Data Communication VE.Direct port, VE.Can port & Bluetooth Synchronised Parallel Operation Yes, up to 25 units with VE.Can General Purpose Analogue/Digital In Port Yes, 2x
£1,610.00 Exc. VAT
£1,932.00 Inc. VAT