Search results for "clenergy"

The cable must be wired to the remote on/off connector of the MultiPlus models: • When used with the MultiPlus 500VA-1200VA models connect the black wire to the ON terminal and the red wire to the (+) terminal. • When used with the MultiPlus Compact 800VA-2kVA models connect the black wire to the middle terminal and the red wire to the right (IN) terminal. • When used with the MultiPlus-II models connect the black wire to the lower (-) terminal and the red wire to the upper (+) remote on-off terminal. Both the Load/Charge Disconnect outputs of Smart BMS CL 12-100 and Load/Charger outputs of the smallBMS must be in ‘High’ state in order for the MultiPlus to operate. After shutdown due to low battery voltage, run the alternator or use a battery charger on the primary side of the BMS to reset the system. The MultiPlus will then switch on and start charging (if connected to an AC power source). Features Battery Management system The BMS connects to 12,8V Victron LiFePO4 (LFP) batteries. Up to 5 batteries may be connected in parallel. Can be used as a system on/off switch. Alternator and battery protection The input current is electronically limited to approximately 90% of the fuse rating. A 100A fuse, for example, will therefore limit the input current to approximately 90A. Choosing the right fuse will: a. Protect the LFP battery against excessive charge current (important in case of a low capacity LFP battery). b. Protect the alternator against overload in case of a high capacity LFP battery bank (most 12V alternators will overheat and fail if running at maximum output during more than 5 minutes). Starter battery Protection This function is similar to that of a Cyrix Battery Combiner or Argo FET Battery Isolator. Current can flow to the LFP battery only if the input voltage (= voltage on the starter battery) exceeds 13V. And current cannot flow back from the LFP battery to the starter battery, thus preventing eventual damage to the LFP battery due to excessive discharge. Li-ion battery protection Excessive input voltage and transients are regulated down to a safe level. The Smart BMS CL will stop charging in case of cell over voltage or over temperature. It has three outputs, similar to the miniBMS Remote on/off input The remote on/off input controls the charging via the alternator. When off, charging via the alternator is disabled, while the BMS functionality will remain active allowing any loads and chargers to continue working regardless of the state of the remote input. When “system on/off switch” is enabled via VictronConnect, the BMS functionality will also be disabled. It consists of two terminals: Remote L and Remote H. A remote on-off switch or relay contact can be connected between H and L. Alternatively, terminal H can be switched to battery plus, or terminal L can be switched to battery minus Ignition proof No relays but MOSFET switches, and therefore no sparks. Brand Victron Energy Manufacturer Part Number ASS070200100 GTIN 8719076051183 Warranty 5 Years

Read more less

CCGX dongle for VE.Bus large systems Brand Victron Energy Manufacturer Part Number BPP900300100 Warranty 5 Years

Read more less

Features Bluetooth Smart The Blue Smart IP22 Charger is the wireless solution to monitor voltage and current, to change settings and to update the charger when new features become available. High efficiency With up to 94% efficiency, these chargers generate up to four times less heat when compared to the industry standard. And once the battery is fully charged, power consumption reduces to 0,5 Watt, some five to ten times better than the industry standard. Adaptive 6-stage charge algorithm: test – bulk – absorption – recondition – float – storage The Blue Smart Charger features a microprocessor controlled ‘adaptive’ battery management. The adaptive feature will automatically optimize the charging process relative to the way the battery is being used. Storage Mode: less maintenance and aging when the battery is not in use The storage mode kicks in whenever the battery has not been subjected to discharge during 24 hours. In the storage mode float voltage is reduced to 2,2V/cell (13,2V for a 12V battery) to minimize gassing and corrosion of the positive plates. Once a week the voltage is raised back to the absorption level to ‘equalize’ the battery. This feature prevents stratification of the electrolyte and sulfation, a major cause of early battery failure. Also charges Li-ion (LiFePO4) batteries LiFePO4 batteries are charged with a simple bulk – absorption – float algorithm. NIGHT and LOW setting When in NIGHT or LOW mode, the output current is reduced to max. 50% of the nominal output and the charger will be totally noiseless. The NIGHT mode automatically ends after 8 hours. The LOW mode can be ended manually. Protected against overheating Output current will reduce as temperature increases up to 50°C, but the Blue Smart Charger will not fail. Eleven LEDs for status indication Charge algorithm: TEST / BULK / ABSORPTION / RECONDITION / FLOAT / STORAGE / READY. MODE button to set: NORMAL (14,4V) / HIGH (14,7V) / RECONDITION / LI-ION. Brand Victron Energy Manufacturer Part Number BPC123047022 Voltage 12 Charger Amps 30A Outputs 1 Efficiency 93% Plug Type UK IP Rating IP22 Dimensions H235 x W108 x D65mm Weight 1.3Kg Warranty 5 Years

Read more less

Brand Victron Energy Manufacturer Part Number CIP142400000 Appr. Voltage Drop 125 mV Cold Resistance 0.3 Warranty 5 Years

Read more less

Features Ultra-fast Maximum Power Point Tracking (MPPT) Especially in case of a clouded sky, when light intensity is changing continuously, an ultra-fast MPPT controller will improve energy harvest by up to 30% compared to PWM charge controllers and by up to 10% compared to slower MPPT controllers. Load output Over-discharge of the battery can be prevented by connecting all loads to the load output. The load output will disconnect the load when the battery has been discharged to a pre-set voltage. Alternatively, an intelligent battery management algorithm can be chosen: see Battery Life. The load output is short circuit proof. Some loads (especially inverters) can best be connected directly to the battery, and the inverter remote control connected to the load output. A special interface cable may be needed, please see the manual. Battery Life: intelligent battery management When a solar charge controller is not able to recharge the battery to its full capacity within one day, the result is often that the battery will continually be cycled between a ‘partially charged’ state and the ‘end of discharge’ state. This mode of operation (no regular full recharge) will destroy a lead-acid battery within weeks or months. The Battery Life algorithm will monitor the state of charge of the battery and, if needed, day by day slightly increase the load disconnect level (i.e. disconnect the load earlier) until the harvested solar energy is sufficient to recharge the battery to nearly the full 100%. From that point onwards the load disconnect level will be modulated so that a nearly 100% recharge is achieved about once every week. Programming, real-time data and history display options Color Control GX or other GX devices: see the Venus documents on our website. A smartphone or other Bluetooth-enabled device: VE.Direct Bluetooth Smart dongle needed. Brand Victron Energy Manufacturer Part Number SCC010015200R GTIN 8719076025337 Battery Voltage 12/24V Auto Select Rated Charge Current 15A Nominal PV Power, 12V 220W Nominal PV Power, 24V 440W Max. PV Short Circuit Current 15A Maximum PV Open Circuit Voltage 100V Efficiency 98% Charge Algorithm Multi-stage adaptive Data Communication Port VE.Direct IP Rating IP43 (electronic components), IP22 (connection area) Dimensions H100 x W113 x D40mm Weight 0.5Kg Warranty 5 Years

Read more less

ESS Kit – Victron Energy 4kW Kit with 2.8kW Solar Array, 5000VA Quattro and 10.2kWh TN Power Li-PO4 Battery Do you want to be more independent and not worry about utility prices then our Energy Storage Solution kits are perfect for you. Using a combination of Victron equipment and lithium battery storage these kits are flexible and professional grade to allow you to be less reliant on the grid. All our kits are professionally mounted on a fireproof board and supplied with industry leading lithium batteries all you need to do is connect to the mains and mount and connect the supplied solar panels. Kit contains the below products and we have included links to each product too so you can see the individual specifications: 8x Victron Energy Solar Panel 360W Mono 2x TN Power 48V 100Ah Heated Lithium Battery 1x Victron Energy Quattro Inverter Charger 48/5000 1x Victron Energy SmartSolar MPPT 250/60 1x Victron Energy Cerbo GX 1x Victron Energy GX Touch 70 1x Victron Energy GX Touch 70 Wall Mount 1x Victron Energy Lynx Distributor 1x Victron Energy RJ45 5m Cable 2m 16mm2 Cable Red 2m 16mm2 Cable Black 4m 50mm2 Cable Red 4m 50mm2 Cable Black 2x T16-8 Copper Tube Lug 10x T50-8 Copper Tube Lug 1x Victron Energy Interface MK3-USB 1x Victron Energy VE.Direct Cable 1.8m 1x Victron Energy VE.Can to CAN-Bus Type B Cable 5m 1x IMO DC PV Isolator Switch 1x Victron Energy SolarCable 6mm2 20m 2x Victron Energy Solar Splitter Pair MC4 (1M-2F / 2M-1F) 1x Victron Energy 58V 125A MEGA-Fuse 1x Victron Energy 58V 250A MEGA-Fuse

Read more less

Features Ultra-fast Maximum Power Point Tracking (MPPT) Especially in case of a clouded sky, when light intensity is changing continuously, an ultra-fast MPPT controller will improve energy harvest by up to 30 % compared to PWM charge controllers and by up to 10 % compared to slower MPPT controllers. Advanced Maximum Power Point Detection in case of partial shading conditions If partial shading occurs, two or more maximum power points may be present on the power-voltage curve. Conventional MPPTs tend to lock to a local MPP, which may not be the optimum MPP. The innovative BlueSolar algorithm will always maximize energy harvest by locking to the optimum MPP. Outstanding conversion efficiency No cooling fan. Maximum efficiency exceeds 98 %. Flexible charge algorithm Fully programmable charge algorithm, and eight pre-programmed algorithms, selectable with a rotary switch (see manual for details). Extensive electronic protection Over-temperature protection and power derating when temperature is high. PV short circuit and PV reverse polarity protection. PV reverse current protection. Internal temperature sensor and optional external battery voltage, temperature and current sensing via Bluetooth A Smart Battery Sense or a BMV-712 Smart Battery Monitor can be used to communicate battery voltage and temperature (and current, in case of a BMV-712 or a SmartShunt) to one or more BlueSolar Charge Controllers. (VE.Direct Bluetooth Smart dongle needed) Real-time data display options Color Control GX or other GX devices: see the Venus documents on our website. A smartphone or other Bluetooth-enabled device: VE.Direct Bluetooth Smart dongle needed. Brand Victron Energy Manufacturer Part Number SCC010070300 GTIN 8719076025528 Battery Voltage 12/24/48V Auto Select (software tool needed to select 36V) Rated Charge Current 70A Nominal PV Power, 12V 1000W Nominal PV Power, 24V 2000W Max. PV Short Circuit Current 50A Maximum PV Open Circuit Voltage 150V absolute maximum coldest conditions 145V start-up and operating maximum Efficiency 98% Charge Algorithm Multi-stage adaptive Data Communication Port VE.Direct IP Rating IP43 (electronic components), IP22 (connection area) Dimensions H215 x W250 x D95mm Weight 3Kg Warranty 5 Years

Read more less

The inverter is equipped with a display to read out battery and inverter details. These parameters can also be read out via Bluetooth by the VictronConnect app. In addition to this, the inverter has a VE.Can Port, for connection to a GX device for system monitoring.  Features Light weight, efficient and quiet Thanks to high frequency technology and a new design this powerful inverter weighs only 11kg. In addition to this it has an excellent efficiency, low standby power, and a very quiet operation. Display and Bluetooth The display reads battery and inverter parameters. The same parameters can be accessed with a smartphone or other Bluetooth enabled device. In addition, Bluetooth can be used to set up the system and to change settings with VictronConnect. VE.Can and VE.Direct port For connection to a GX device for system monitoring, data logging, and remote firmware updates. I/O Connections Programmable Relay, temperature sensor and voltage sensor connections. The remote input can also be configured to accept the Victron smallBMS. Brand Victron Energy Manufacturer Part Number PIN482600000 GTIN 8719076046059 Voltage 48V Cont. Output Power at 25°C 6000VA Peak Power 9kW for 3 seconds Output AC Voltage 230V Protection Category IP21 Bluetooth Enabled Yes Dimensions H425 x W440 x D125mm Weight 11Kg Warranty 5 Years

Read more less

The Argo Battery Isolators feature a low voltage drop thanks to the use of Schottky diodes: at low current the voltage drop is approximately 0,3 V and at the rated output approximately 0,45 V. All models are fitted with a compensation diode that can be used to slightly increase the output voltage of the alternator. This compensates for the voltage drop over the diodes in the isolator. Please see Victron Energy’s ‘Energy Unlimited’ or ask for specialist advice when installing a diode isolator. Simply inserting the isolator in the cabling between the alternator and the batteries will slightly reduce charge voltage. The result can be that batteries are not charged to the full 100% and age prematurely. Alternator energize input Some alternators need DC voltage on the B+ output to start charging. Obviously, DC will be present when the alternator is directly connected to a battery. Inserting a Diode or FET splitter will however prevent any return voltage/current from the batteries to the B+, and the alternator will not start. The new ‘AC’ diode isolators feature a special current limited energize input that will power the B+ when the engine run/stop switch is closed. Brand Victron Energy Manufacturer Part Number ARG140301020R GTIN 8719076019107 Maximum Charge Current 140A Maximum Alternator Current 140A Number of Batteries 3 Alternator Energize Input Yes Connection M8 Studs Compensation Diode & Energize Connection 6.3mm Faston Dimensions H60 x W120 x D150mm Weight 1.1Kg Warranty 5 Years    

Read more less

Features All-in-one solar power solution The EasySolar combines a MPPT solar charge controller, an inverter/charger and AC distribution in one enclosure. The product is easy to install, with a minimum of wiring.   The solar charge controller: Blue Solar MPPT 100/50 Up to three strings of PV panels can be connected to three sets of MC4 (PV-ST01) PV connectors.   The inverter/charger: MultiPlus Compact 12/1600/70 or 24/1600/40 The MPPT charge controller and the MultiPlus Compact inverter/charger share the DC battery cables (included). The batteries can be charged with solar power (BlueSolar MPPT) and/or with AC power (inverter/charger) from the utility grid or a genset.   AC distribution The AC distribution consists of a RCD (30 mA/16 A) and four AC outputs protected by two 10A and two 16A circuit breakers. One 16A output is controlled by the AC input: it will switch on only when AC is available.   PowerAssist Unique PowerAssist technology protects the utility or generator supply from being overloaded by adding extra inverter power when needed.   Unique solar application software Several software programs (Assistants) are available to configure the system for various grid interactive or stand-alone applications.   Brand Victron Energy Manufacturer Part Number CEP121620000 GTIN 8719076021599 Voltage 12V Transfer Switch 16A Continuous Output Power at 25°C 1600VA/1300W Peak power 3000W Charger Current House Battery 70A Battery Temperature Sensor Yes Programmable Relay Yes Ingress Protection IP22 Battery-Connection Battery cables of 1.5 meter Dimensions (Including Terminals) H745 x W214 x D110mm Weight 15Kg Warranty 5 Years Country of Manufacture China

Read more less

Features Uninterrupted AC power (UPS function) In the event of a grid failure, or when shore or generator power is disconnected, the inverter within the Multi is automatically activated and takes over the supply to the connected loads. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption Remote Monitoring and Control Monitor and control your MultiPlus and system or systems’ locally (LAN) or remotely via the internet from anywhere in the world, using the free VRM app and free VRM portal website. Access can be from a phone, tablet, laptop or PC for multiple operating systems. There is no end to the level of control, via the required Color Control GX or Venus GX, from adjusting your MultiPlus to setting a Geofence for hire vehicles and more… Proven reliability The full bridge plus toroidal transformer topology has proven its reliability over many years. The inverter is short circuit proof and protected against overheating, whether due to overload or high ambient temperature.  PowerControl – Dealing with limited generator, shore side or grid power With the Multi Control Panel a maximum generator or shore current can be set. The MultiPlus will then take account of other AC loads and use whatever is extra for charging, thus preventing the generator or shore supply from being overloaded. PowerAssist – Boosting the capacity of shore or generator power Where peak power is so often required only for a limited period, the MultiPlus will make sure that insufficient shore or generator power is immediately compensated for by power from the battery. When the load reduces, the spare power is used to recharge the battery. High start-up power Needed to start high inrush loads such as power converters for LED lamps, halogen lamps or electric tools Programmable relay By default, the programmable relay is set as an alarm relay, i.e. the relay will de-energise in the event of an alarm or a pre-alarm (inverter almost too hot, ripple on the input almost too high, battery voltage almost too low). Brand Victron Energy Manufacturer Part Number PMP482120000 Voltage 48 Transfer Switch (A) 16 Cont. Output Power at 25°C (VA) 1200 Peak Power (W) 2400 Max Efficiency 95% Zero Load Power (W) 10 Charge Current House Battery (A) 13 Charge Current Starter Battery (A) 1 (12V and 24V models only) Battery Temperature Sensor Yes Programmable Relay Yes Remote on-off On/off/charger only Protection Category IP21 Dimensions H406 x W250 x D100mm Weight (kg) 8.2 Warranty 5 Years Country of Manufacture China

Read more less

Features Two AC Outputs The main output has no break functionality. The MultiPlus takes over the supply to the connected loads in the event of a grid failure or when shore/generator power is disconnected. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption. The second output is live only when AC is available on the input of the MultiPlus. Loads that should not discharge the battery, like a water heater for example can be connected to this output (second output available on models rated at 3 kVA and more). Virtually unlimited power thanks to parallel operation Up to 6 Multis can operate in parallel to achieve higher power output. Six 24/5000/120 units, for example, will provide 25 kW / 30 kVA output power with 720 Amps charging capacity. Three phase capability In addition to parallel connection, three units of the same model can be configured for three phase output. But that’s not all: up to 6 sets of three units can be parallel connected for a huge 75 kW / 90 kVA inverter and more than 2000 Amps charging capacity. PowerControl – Dealing with limited generator, shore side or grid power The MultiPlus is a very powerful battery charger. It will therefore draw a lot of current from the generator or shore side supply (nearly 10 A per 5 kVA Multi at 230 VAC). With the Multi Control Panel a maximum generator or shore current can be set. The MultiPlus will then take account of other AC loads and use whatever is extra for charging, thus preventing the generator or shore supply from being overloaded. PowerAssist – Boosting the capacity of shore or generator power This feature takes the principle of PowerControl to a further dimension. It allows the MultiPlus to supplement the capacity of the alternative source. Where peak power is so often required only for a limited period, the MultiPlus will make sure that insufficient shore or generator power is immediately compensated for by power from the battery. When the load reduces, the spare power is used to recharge the battery. Solar energy: AC power available even during a grid failure The MultiPlus can be used in off grid as well as grid connected PV and other alternative energy systems. Loss of mains detection software is available. System configuring In case of a stand-alone application, if settings have to be changed, this can be done in a matter of minutes with a DIP switch setting procedure. Parallel and three phase applications can be configured with VE.Bus Quick Configure and VE.Bus System Configurator software. Brand Victron Energy Manufacturer Part Number CMP241620000 Voltage 24 Transfer Switch (A) 16 Cont. Output Power at 25°C (VA) 1600 Peak Power (W) 3000 Max Efficiency 94% Zero Load Power (W) 10 Charge Current House Battery (A) 40 Charge Current Starter Battery (A) 4 (12 V and 24 V models only) Battery Temperature Sensor Yes Programmable Relay Yes Remote on-off Yes Protection Category IP21 Dimensions H375 x W214 x D110mm Weight (kg) 10 Warranty 5 Years Country of Manufacture China

Read more less

The Phoenix 24/3000 has pure sine wave output, high peak power and high efficiency. Combined high frequency and line frequency technologies ensure the best of both worlds. Features of the Phoenix 24/3000 SinusMax – Superior engineering Developed for professional duty, the Phoenix range of inverters is suitable for the widest range of applications. The design criteria have been to produce a true sine wave inverter with optimized efficiency but without compromise in performance. Employing hybrid HF technology, the result is a top quality product with compact dimensions, light in weight and capable of supplying power, problem-free, to any load. Extra start-up power A unique feature of the SinusMax technology is very high start-up power. Conventional high frequency technology does not offer such extreme performance. Phoenix Inverters, however, are well suited to power up difficult loads such as refrigeration compressors, electric motors and similar appliances. Virtually unlimited power thanks to parallel and 3-phase operation capability Up to 6 units inverters can operate in parallel to achieve higher power output. Six 24/5000 units, for example, will provide 24kW / 30kVA output power. Operation in 3-phase configuration is also possible. To transfer the load to another AC source: the automatic transfer switch If an automatic transfer switch is required we recommend using the MultiPlus inverter/charger instead. The switch is included in these products and the charger function of the MultiPlus can be disabled. Computers and other electronic equipment will continue to operate without disruption because the MultiPlus features a very short switchover time (less than 20 milliseconds). Communications interface These larger Phoenix inverter models come with a VE.Bus port. All you need to connect to your PC is our MK3- USB VE.Bus to USB interface (see under accessories). Together with our VictronConnect or VEConfigure software, which can be downloaded free of charge from our website, parameters of the inverters can be customized. This includes output voltage and frequency, over and under voltage settings and programming the relay. This relay can for example be used to signal several alarm conditions, or to start a generator. The inverters can also be connected to a GX device (eg Cerbo GX) for monitoring and control. Control over system Want to have perfect control over your system from wherever you are whilst using your Phoenix Inverter 24/3000, why not have a look at the Cerbo GX. Simply connect through the Victron Remote Management (VRM) portal, or access directly, using the separate GX Touch, a MFD or the VictronConnect App thanks to its added Bluetooth capability. This latest addition to the GX-range combines all the best of connectivity, redefining smart power solutions in every way. Watch the new video that explains all there is to know about installing the new Cerbo GX & GX Touch 50 Not sure what size inverter you need, why not take a look at our guide to sizing an inverter.

Read more less

Features VRLA technology VRLA stands for Valve Regulated Lead Acid, which means that the batteries are sealed. Gas will escape through the safety valves only in case of overcharging or cell failure. VRLA batteries are maintenance free for life. Sealed (VRLA) AGM Batteries AGM stands for Absorbent Glass Mat. In these batteries the electrolyte is absorbed into a glass-fibre mat between the plates by capillary action. As explained in our book ‘Energy Unlimited’, AGM batteries are more suitable for short-time delivery of high currents than gel batteries. Low Self-Discharge Because of the use of lead calcium grids and high purity materials, Victron VRLA batteries can be stored during long periods of time without recharge. The rate of self-discharge is less than 2% per month at 20°C. The self-discharge doubles for every increase in temperature by 10°C. Victron VRLA batteries can therefore be stored for up to a year without recharging, if kept under cool conditions. Exceptional Deep Discharge Recovery Victron VRLA batteries have exceptional discharge recovery, even after deep or prolonged discharge. Nevertheless repeatedly deep and prolonged discharge has a very negative effect on the service life of all lead acid batteries, Victron batteries are no exception. Battery Discharging Characteristics The rated capacity of Victron AGM and Gel Deep Cycle batteries refers to 20 hour discharge, in other words: a discharge current of 0,05 C. The rated capacity of Victron Tubular Plate Long Life batteries refers to 10 hours discharge. The effective capacity decreases with increasing discharge current (see table 1). Please note that the capacity reduction will be even faster in case of a constant power load, such as an inverter.  All Prices Include VAT   Brand Victron Energy Manufacturer Part Number BAT212200084 GTIN 8719076036944 Voltage 12V Battery Capacity (C20) 22Ah Terminal Type M8 Terminal Layout Right Hand Positive Dimensions (Including Terminals) L181 x W77 x H167mm Weight 5.8kg Warranty 2 Years Country of Manufacture Vietnam Battery Technology AGM Battery Application Deep Cycle  

Read more less

Features of the - Victron Energy EasyPlus Compact 12V/1600VA 70-16A - 230V Multi-functional power solution The EasyPlus is a multifunctional energy system consisting of a powerful sine wave inverter, a sophisticated battery charger, a high speed AC transfer switch and AC distribution in a single light weight and compact enclosure. The system has been designed for those who want to enjoy the comfort and freedom of a complete energy system without spending time on the installation of separate components and difficult technical procedures. Optimum comfort and safety The EasyPlus guarantees uninterrupted power supply, whenever and wherever you are. Where shore or generator power is limited, the unique PowerAssist® technology makes it possible to boost the total capacity by adding extra energy from the batteries. Optimum safety is guaranteed with the integrated RCD (Residual Current Device) protecting against earth leakage.  

Read more less

  ManufacturerVictron Energy Commodity Code85072080 Dimensions (mm) (H x W x D)220 x 290 x 24

Read more less

Simply mounted The GX Touch is optimised to more than meet the standards of installer professionals. The screen is simply bolted on top of a dashboard, eliminating the need to create perfect cut-outs (like with the ColorControl GX) and is connected through just one cable, taking away the hassle of having to bring many wires to a dashboard.  The GX Touch 50 is a companion to the Cerbo GX, the all-new communication-centre allows you to always have perfect control over your system from wherever you are and maximises its performance. Simply connect through our Victron Remote Management (VRM) portal, or access directly, using the GX Touch 50, a MFD or our VictronConnect app thanks to its added Bluetooth capability. This latest addition to the GX-range combines all the best of connectivity, redefining smart power solutions in every way Brand Victron Energy Manufacturer Part Number BPP900455050 Warranty 5 Years

Read more less

The EM24 is for 3 phase monitoring only. To measure the power and energy of the whole application at the distribution box. Or to measure the output of a PV Inverter, to display the data on the Color Control GX. The Energy Meter can be used as a: Grid meter, and used as control input for an ESS System. Measure the output of a PV Inverter Measure the output of a AC Genset The meter is connected to the Color Control GX. There are two options in its wiring: Direct connection, either using the RS485 to USB interface with 1.8m cable length, or the 5.0m cable. Wireless connection via Zigbee Brand Victron Energy Manufacturer Part Number REL200200100 GTIN 8719076051268 Warranty 5 Years

Read more less

Features GMDSS The Global Maritime Distress & Safety System (GMDSS) was developed by the International Maritime Organisation (IMO) to improve maritime distress and safety communications. Power supply The Skylla TG has proven itself to be an excellent battery charger and power supply for GMDSS applications. However, when using a standard Skylla Charger, additional equipment is needed to perform the monitoring and alarm functions required for GMDSS. Installation made easy: the Skylla GMDSS The Victron Skylla GMDSS Charger has been designed to provide all required monitoring and alarm data. Both the battery and the GMDSS system are connected directly to the charger. Data and alarms are displayed on a digital panel (VE.Net GMDSS panel, to be ordered separately). A standard eight wire UTP-cable connects the charger to the panel. No adjustments needed The whole system is ‘click and go’: the panels are pre-programmed for GMDSS functionality. A simple, intuitive menu allows changing of settings if required. Battery time to go The Skylla GMDSS charger has a built-in battery controller. The capacity of the battery is fully monitored so the panel can even indicate the ’time to go’ in case of a power supply black out. Perfect charger for any type of battery Charge voltage can be precisely adjusted to suit any VRLA or flooded battery system Brand Victron Energy Manufacturer Part Number SDTG2400302 Voltage 24 Charge Current (A) 30 (limited to 22A at 110VAC) Input Voltage 230VAC Temperature Sensor Yes Can Be Used As Power Supply Yes IP Rating IP21 Dimensions H485 x W250 x D147mm Weight (kg) 6 Warranty 5 Years

Read more less

ESS Kit – Victron Energy 4kW Kit with 3.2kW Solar Array, 5000VA EasySolar-II and 10.2kWh Topband Li-PO4 Battery Do you want to be more independent and not worry about utility prices then our Energy Storage Solution kits are perfect for you. Using a combination of Victron equipment and lithium battery storage these kits are flexible and professional grade to allow you to be less reliant on the grid. All our kits are professionally mounted on a fireproof board and supplied with industry leading lithium batteries all you need to do is connect to the mains and mount and connect the supplied solar panels. Kit contains the below products and we have included links to each product too so you can see the individual specifications: 8x Victron Energy Solar Panel 360W Mono 2x TopBand RS-R Series 51.2V 100Ah Lithium Battery 1x TopBand External Communication Cable 1x TopBand Amphenol Power Cable Positive 1x TopBand Amphenol Power Cable Negative 1x Victron Energy EasySolar Inverter Charger 48/5000 MPPT 250/100 1x Victron Energy Lynx Distributor 1x Victron Energy RJ45 5m Cable 4m 50mm2 Cable Red 4m 50mm2 Cable Black 10x T50-8 Copper Tube Lug 1x Victron Energy Interface MK3-USB 1x Victron Energy VE.Direct Cable 1.8m 1x IMO DC PV Isolator Switch 1x Victron Energy SolarCable 6mm2 20m 2x Victron Energy Solar Splitter Pair MC4 (1M-2F / 2M-1F) 1x Victron Energy 58V 200A MEGA-Fuse

Read more less

The advantages of lead carbon therefore are: Less sulfation in case of partial state-of-charge operation. Lower charge voltage and therefore higher efficiency and less corrosion of the positive plate. And the overall result is improved cycle life. Failure modes of flat plate VRLA lead acid batteries in case of intensive cycling The most common failure modes are: Softening or shedding of the active material. During discharge the lead oxide (PbO2) of the positive plate is transformed into lead sulfate (PbSO4), and back to lead oxide during charging. Frequent cycling will reduce cohesion of the positive plate material due to the higher volume of lead sulfate compared to lead oxide. Corrosion of the grid of the positive plate. This corrosion reaction accelerates at the end of the charge process due to the, necessary, presence of sulfuric acid. Sulfation of the active material of the negative plate. During discharge the lead (Pb) of the negative plate is also transformed into lead sulfate (PbSO4). When left in a low state-of-charge, the lead sulfate crystals on the negative plate grow and harden and form and impenetrable layer that cannot be reconverted into active material. The result is decreasing capacity, until the battery becomes useless. It takes time to recharge a lead acid battery Ideally, a lead acid battery should be charged a rate not exceeding 0,2C, and the bulk charge phase should be followed by eight hours of absorption charge. Increasing charge current and charge voltage will shorten recharge time at the expense of reduced service life due to temperature increase and faster corrosion of the positive plate due to the higher charge voltage. Lead carbon: better partial state-of-charge performance, more cycles, and higher efficiency Replacing the active material of the negative plate by a lead carbon composite potentially reduces sulfation and improves charge acceptance of the negative plate. The advantages of lead carbon therefore are: Less sulfation in case of partial state-of-charge operation. Lower charge voltage and therefore higher efficiency and less corrosion of the positive plate. And the overall result is improved cycle life. Tests have shown that our lead carbon batteries do withstand at least five hundred 100% DoD cycles. The tests consist of a daily discharge to 10,8V with I = 0,2C20, followed by approximately two hours rest in discharged condition, and then a recharge with I = 0,2C20. (Several manufacturers of lead carbon batteries claim a cycle life of up to two thousand 90% DoD cycles. We have not yet been able to confirm these claims) Brand Victron Energy Manufacturer Part Number BAT612110081 Voltage 12 Capacity (C20) 106 Cold Cranking (EN) 500 Terminal Type M8 Terminal Layout LH+ Dimensions (Including Terminals) L410 x W172 x H225mm Weight (kg) 36 Warranty 2 Years Battery Technology Lead Carbon

Read more less

  Built to Last in Demanding Conditions 30kWh Capacity: Store enough energy to power your home or business through outages or peak demand periods. Six (6) SR51.2V Server Rack Batteries: Each battery is meticulously designed and packed with premium components including Grade A cells and PACE BMS. UK-Designed Heating System: Efficiently charges even in cold environments thanks to the internal heating system. 8-Year Warranty: We stand behind the quality and performance of our products. Unmatched Versatility and Control Pre-loaded Inverter Protocols: Seamless integration with Victron, Pylontech, Growatt, Solis, Sofar, Goodwe. 4.3" TFT LCD Touchscreen: Monitor your system status in detail with a user-friendly interface. Change the Inverter protocol via your touchscreen! 10-15 Year Lifecycle: Expect long-lasting performance from our superior design. 16 Grade A EVE Cells: Industry-leading cell technology delivers exceptional life (4000 cycles @ 80% DOD). Safety and Scalability 125Amp DC Breaker: Provides automatic protection against electrical faults. Parallel Connection: Expand your storage capacity as your needs grow. Series connection not supported. Integrated High-Quality Busbars: Our cabinets feature thick nickel-plated copper busbars for simple and reliable parallel battery connection. Vented Design and Cable Management: Vented front panels ensure airflow, while unique circular cut-out cable access points (top and bottom) allow for clean and easy cable routing. Scalable Storage: Connect up to 15 units in parallel to expand your storage capacity as your needs grow. (Series connection not supported.) Available Cabinet Sizes: This bundle includes the 6 Rack Cabinet (30kWh). However, we also offer a 3-cabinet 15kWh bundle. Cabinet Dimensions: 600 x 650 x 1250mm. Manufacturer: Fogstar Energy Model: ESR51.2V 5.12KWH EVE Cell Model: LF100LA Cell Assembly: 16S1P Cycle Life: 4000 Cycles at 1C to 80%. (After 4000 cycles, you will still have a battery that can deliver 80% of the stated capacity) 5.12Kwh is fully useable. BMS: PACE 100A BMS Maximum Discharge: 100A per rack unit (600A for a 30kWh bundle) Balance Current: 0.5A Capacity: 100ah Weight: 45.2kg Nominal Voltage: 51.2V Rack Unit Size: 3.5U Size: 155mm x 450mm x 440mm Pre-loaded Inverter Protocols: Victron, Sofar, Pylontech, Growatt, Solis, Goodwe. Fogstar ESR51.2V 5.12KWH Rack Battery (x6) Fogstar ESR51.2V 3 Battery Rack Cabinet (x1) PC communication cable RS232 to USB (x1) Battery to Battery (B2B) communication cable (RS485 to RS485) (x6) Positive 'dual' 8AWG cables (x12) Negative 'dual' 8AWG cables (x12) M6 threaded screws, bolts and washers for securing Racks to Cabinets (x36)

Read more less

Features SinusMax – Superior engineering Developed for professional duty, the Phoenix range of inverters is suitable for the widest range of applications. The design criteria have been to produce a true sine wave inverter with optimized efficiency but without compromise in performance. Employing hybrid HF technology, the result is a top quality product with compact dimensions, light in weight and capable of supplying power, problem-free, to any load. Extra start-up power A unique feature of the SinusMax technology is very high start-up power. Conventional high frequency technology does not offer such extreme performance. Phoenix Inverters, however, are well suited to power up difficult loads such as refrigeration compressors, electric motors and similar appliances. Virtually unlimited power thanks to parallel and 3-phase operation capability Up to 6 units inverters can operate in parallel to achieve higher power output. Six 24/5000 units, for example, will provide 24kW / 30kVA output power. Operation in 3-phase configuration is also possible.  To transfer the load to another AC source: the automatic transfer switch If an automatic transfer switch is required we recommend using the MultiPlus inverter/charger instead. The switch is included in these products and the charger function of the MultiPlus can be disabled. Computers and other electronic equipment will continue to operate without disruption because the MultiPlus features a very short switchover time (less than 20 milliseconds). Computer interface All models have a RS-485 port. All you need to connect to your PC is our MK3-USB VE.Bus to USB interface (see under accessories). Together with our VEConfigure software, which can be downloaded free of charge from our website, all parameters of the inverters can be customized. This includes output voltage and frequency, over and under voltage settings and programming the relay. This relay can for example be used to signal several alarm conditions, or to start a generator. The inverters can also be connected to VENet, the new power control network of Victron Energy, or to other computerized monitoring and control systems. Brand Victron Energy Manufacturer Part Number PIN485020000 Voltage 48 VA 5000 Peak Power (W) 10000 Max Efficiency 95% Programmable Relay Yes IP Rating IP21 Dimensions (Including Terminals) H444 x W328 x D240mm Weight (kg) 30 Warranty 5 Years

Read more less

Features Bluetooth built-in: fully configurable with a tablet or smartphone Low battery voltage alarm Low battery voltage cut-off and restart levels Dynamic cut-off: load dependent cut-off level Output voltage: 210 – 245V Frequency: 50 Hz or 60 Hz ECO mode on/off and ECO mode sense level Alarm relay Monitoring: In- and output voltage, load and alarms VE.Direct communication port The VE.Direct port can be connected to a computer (VE.Direct to USB interface cable needed) to configure and monitor the same parameters. Proven reliability The full bridge plus toroidal transformer topology has proven its reliability over many years. The inverters are short circuit proof and protected against overheating, whether due to overload or high ambient temperature. High start-up power Needed to start loads such as power converters for LED lamps, halogen lamps or electric tools. ECO mode When in ECO mode, the inverter will switch to standby when the load decreases below a preset value. Once in standby the inverter will switch on for a short period every 2,5 seconds (adjustable). If the load exceeds the preset level, the inverter will remain on. Remote on/off A remote on/off switch or relay contact can be connected to a two pole connector. Alternatively, the H terminal (left) of the two pole connector can be switched to battery plus, or the L terminal (right) of the two pole connector can be switched to battery minus (or the chassis of a vehicle, for example). To transfer the load to another AC source: the automatic transfer switch For our low power inverters we recommend our Filax Automatic Transfer Switch. The Filax features a very short switchover time (less than 20 milliseconds) so that computers and other electronic equipment will continue to operate without disruption. Alternatively use a MultiPlus with built-in transfer switch Brand Victron Energy Manufacturer Part Number PIN482200000 Voltage 48 VA 2000 Peak Power (VA) 4000 Max Efficiency 94% IP Rating IP21 Dimensions (Including Terminals) H485 x 219 x 125mm Weight (kg) 13 Warranty 5 Years

Read more less

Features Multifunctional, with intelligent power management The MultiPlus is a powerful true sine wave inverter, a sophisticated battery charger that features adaptive charge technology, and a high-speed AC transfer switch in a single compact enclosure. Next to these primary functions, the MultiPlus has several advanced features, as outlined below. Parallel operation and three phase capability Up to six Multis can operate in parallel to achieve higher power output. In addition to parallel connection, three units can be configured for three-phase output. PowerControl – Dealing with limited generator, shore side or grid power With the Multi Control Panel a maximum generator or shore current can be set. The MultiPlus will then take account of other AC loads and use whatever is extra for charging, thus preventing the generator or shore supply from being overloaded. PowerAssist – Boosting the capacity of shore or generator power This feature takes the principle of PowerControl to a further dimension. It allows the MultiPlus to supplement the capacity of the alternative source. Where peak power is so often required only for a limited period, the MultiPlus will make sure that insufficient shore or generator power is immediately compensated for by power from the battery. When the load reduces, the spare power is used to recharge the battery. Four stage adaptive charger and dual bank battery charging The main output provides a powerful charge to the battery system by means of advanced ‘adaptive charge’ software. The software fine-tunes the three-stage automatic process to suit the condition of the battery, and adds a fourth stage for long periods of float charging. The adaptive charge process is described in more detail on the Phoenix Charger datasheet and on our website, under Technical Information. In addition to this, the MultiPlus will charge a second battery using an independent trickle charge output intended for a main engine or generator starter battery. High start-up power Needed to start high inrush loads such as power converters for LED lamps, halogen lamps or electric tools. Search Mode When Search Mode is ‘on’, the power consumption of the inverter in no-load operation is decreased by approx. 70%. In this mode the Multi, when operating in inverter mode, is switched off in case of no load or very low load, and switches on every two seconds for a short period. If the output current exceeds a set level, the inverter will continue to operate. If not, the inverter will shut down again. Programmable relay By default, the programmable relay is set as an alarm relay, i.e. the relay will de-energise in the event of an alarm or a pre-alarm (inverter almost too hot, ripple on the input almost too high, battery voltage almost too low). Remote on / off / charger on Three pole connector. On-site system configuring, monitoring and control After installation, the MultiPlus is ready to go. Some settings can be changed with DIP switches. 500/800/1200VA models: remote switch / battery charge voltage / inverter frequency /search mode. 1600/2000VA models: battery charge voltage /search mode. For more settings use VE-Config or the VE.Bus Smart dongle. Remote configuring and monitoring Install a Cerbo GX or other GX product to connect to the internet. Operational data can be stored and displayed on our VRM (Victron Remote Management) website, free of charge. When connected to the internet, systems can be accessed remotely, and settings can be changed. Brand Victron Energy Manufacturer Part Number PMP482200000 GTIN 8719076049470 Voltage 48V Cont. output power at 25ºC 2000VA Peak Power 3500W Output AC Voltage 230V Transfer Switch 35A Charge Current House Battery 25A Protection Category IP22 Efficiency 95% Bluetooth Compatible No Dimensions H506 x W236 x D147mm Weight 15.5Kg Warranty 5 Years

Read more less

The batteries can be connected in parallel. Series connection is not allowed.  Features Integrated BMS and safety switch The SuperPack batteries are extremely easy to install, needing no additional components. The internal switch will disconnect the battery in case of over discharge, over charge or high temperature. Abuse proof A lead-acid battery will fail prematurely due to sulfation: If it operates in deficit mode during long periods of time (i.e. if the battery is rarely, or never at all, fully charged). If it is left partially charged or worse, fully discharged. A Lithium-Ion battery does not need to be fully charged. Service life even slightly improves in case of partial charge instead of a full charge. This is a major advantage of Li-ion compared to lead-acid. The SuperPack batteries will cut-off the charge or discharge current when the maximum ratings are exceeded. Efficient In several applications (especially off-grid solar), energy efficiency can be of crucial importance. The round-trip energy efficiency (discharge from 100% to 0% and back to 100% charged) of the average lead-acid battery is 80%. The round-trip energy efficiency of a Li-ion battery is 92%. The charge process of lead-acid batteries becomes particularly inefficient when the 80% state of charge has been reached, resulting in efficiencies of 50% or even less in solar systems where several days of reserve energy are required (battery operating in 70% to 100% charged state). In contrast, a Li-ion battery will still achieve 90% efficiency even under shallow discharge conditions. Can be connected in parallel The batteries can be connected in parallel. Series connection is not allowed. Use in upright position only. Brand Victron Energy Manufacturer Part Number BAT512020705 GTIN 8719076047537 Voltage 12.8V Battery Capacity (C20) 20Ah Terminal Type M6 Terminal Layout Right Hand Positive Dimensions (Including Terminals) H167 x W181 x D77mm Weight 3.5Kg Warranty 3 Years Country of Manufacture China Battery Technology Lithium Battery Application Deep Cycle

Read more less

Features Control Your Charger Remotely The MPPT VE.Can SmartSolar charger can be remotely controlled and configured over Bluetooth via the VictronConnect App. This allows device set-up, management, and at-a-glance information, such as battery voltage and current, PV voltage and current, and historical data.  Daisy Chain Additional Units The VE.Can SmartSolar charger is equipped with CAN bus ports. This allows for communication with additional VE.Can SmartSolar chargers. The additional units are simply “daisy chained” to each other with a single RJ45 cable between the individual units. When connected to each other, all individual VE.Can SmartSolar chargers, will synchronise their charge stages. They can also send their data, via a single cable, to a GX monitoring device.  Remote Monitoring and Control If the GX device is connected to the internet, the Victron Remote Management Portal (VRM) provides access to the full power of your solar charger(s). For remote installations – even when there is no internet connection nearby – you may be able to monitor your MPPT by connecting the GlobalLink 520. Ultra-fast Maximum Power Point Tracking (MPPT) Especially in case of a clouded sky, when light intensity is changing continuously, an ultra-fast MPPT controller will improve energy harvest by up to 30% compared to PWM charge controllers and by up to 10% compared to slower MPPT controllers. Advanced Maximum Power Point Detection in case of partial shading conditions If partial shading occurs, two or more maximum power points (MPP) may be present on the powervoltage curve. Conventional MPPTs tend to lock to a local MPP, which may not be the optimum MPP. The innovative SmartSolar algorithm will always maximize energy harvest by locking to the optimum MPP. Outstanding conversion efficiency No cooling fan. Maximum efficiency exceeds 98%. Flexible charge algorithm Fully programmable charge algorithm, and eight pre-programmed algorithms, selectable with a rotary switch (see manual for details). Extensive electronic protection Over-temperature protection and power derating when temperature is high. PV short circuit and PV reverse polarity protection. PV reverse current protection. Bluetooth Smart built-in The wireless solution to set-up, monitor, update and synchronise SmartSolar Charge Controllers. Internal temperature sensor and optional external battery voltage, temperature and current sensing via Bluetooth A Smart Battery Sense, a BMV-712 Smart Battery Monitor or a SmartShunt can be used to communicate battery voltage and temperature (and current, in case of a BMV 712 or a SmartShunt) to one or more SmartSolar Charge Controllers. VE.Direct or VE.Can For a wired data connection to a Color Control GX, other GX products, PC or other devices Fully discharged battery recovery function Will initiate charging even if the battery has been discharged to zero volts. Will reconnect to a fully discharged Li-ion battery with integrated disconnect function. VE.Can: the multiple controller solution Up to 25 units can be synchronised with VE.Can, and up to 10 units with Bluetooth Remote on-off To connect for example to a VE.BUS BMS. Programmable relay Can be programmed to trip on an alarm, or other events. Optional: SmartSolar pluggable LCD display Simply remove the rubber seal that protects the plug on the front of the controller, and plug-in the display. Brand Victron Energy Manufacturer Part Number SCC115085411 GTIN 8719076050339 Battery Voltage 12/24/48V Auto Select (36V: manual) Rated Charge Current 85A Nominal PV Power, 12V 1200W Nominal PV Power, 24V 2400W Max. PV Short Circuit Current 70A Maximum PV Open Circuit Voltage 150V absolute maximum coldest conditions, 145V start-up and operating maximum Efficiency 98% Charge Algorithm multi-stage adaptive (eight preprogrammed algorithms) or user defined algorithm Data Communication Port VE.Can, VE.Direct and Bluetooth IP Rating IP43 (electronic components), IP22 (connection area) Dimensions H216 x W295 x D103mm Weight 4.5Kg Warranty 5 Years

Read more less

A lithium-ion battery pack with intrinsically safe LiFePO4 cells, a built-in charger, and suitable for high discharge currents. Nominal voltage: 12.8V Battery capacity: 8Ah to 40Ah (not suitable for parallel or series connection)   Features Lightweight and easy to install Ideal for mobile applications. Effective protection against improper use Ideal for solar power and other applications where excessive discharge might quickly cause damage to lead acid batteries. Storage mode Reduces power consumption to almost zero. Prevents damage due to excessive discharge of the battery during storage. Remote control with status indicator Push button (supplied) with a dual-colour LED status indicator: Short push of the button: high capacity output activated for 30 minutes (mover applications), red LED. Hold down for 2 seconds: high capacity output always activated, slow flashing red LED. Hold down for 5 seconds: storage mode, blue LED flashes 10 times. Battery is charged via input 1:slow flashing blue LED. Battery fully charged: blue LED. Overload or overheating: flashing red LED. VE.Direct port: can be connected to a PC or smartphone (‘VE.Direct to USB’ or ‘VE.Direct Bluetooth Smart dongle’ required) – Operation: Output 1: on / 30-minute timer / off Output 2: on/off Input 1: on/off – Monitoring: Battery voltage Temperature and alarms Brand Victron Energy Manufacturer Part Number PPP012040000 Voltage 12.8 Capacity (C20) 40 Stored Energy 512Wh Battery Technology Lithium Continuous Output Current 150A Dimensions (Including Terminals) H212 x W190 x D172mm Short-circuit Current 300A Weight (kg) 8.6 Warranty 3 Years

Read more less

The batteries can be connected in parallel. Series connection is not allowed.  Features Integrated BMS and safety switch The SuperPack batteries are extremely easy to install, needing no additional components. The internal switch will disconnect the battery in case of over discharge, over charge or high temperature. Abuse proof A lead-acid battery will fail prematurely due to sulfation: If it operates in deficit mode during long periods of time (i.e. if the battery is rarely, or never at all, fully charged). If it is left partially charged or worse, fully discharged. A Lithium-Ion battery does not need to be fully charged. Service life even slightly improves in case of partial charge instead of a full charge. This is a major advantage of Li-ion compared to lead-acid. The SuperPack batteries will cut-off the charge or discharge current when the maximum ratings are exceeded. Efficient In several applications (especially off-grid solar), energy efficiency can be of crucial importance. The round-trip energy efficiency (discharge from 100% to 0% and back to 100% charged) of the average lead-acid battery is 80%. The round-trip energy efficiency of a Li-ion battery is 92%. The charge process of lead-acid batteries becomes particularly inefficient when the 80% state of charge has been reached, resulting in efficiencies of 50% or even less in solar systems where several days of reserve energy are required (battery operating in 70% to 100% charged state). In contrast, a Li-ion battery will still achieve 90% efficiency even under shallow discharge conditions. Can be connected in parallel The batteries can be connected in parallel. Series connection is not allowed. Use in upright position only. Brand Victron Energy Manufacturer Part Number BAT512060705 Voltage 12.8 Capacity (C20) 60 Terminal Type M6 Terminal Layout LH+ Dimensions (Including Terminals) L229 x W138 x D213mm Weight (kg) 9.5 Warranty 3 Years Battery Technology Lithium

Read more less

Features Ultra-fast Maximum Power Point Tracking (MPPT) Especially in case of a clouded sky, when light intensity is changing continuously, an ultra-fast MPPT controller will improve energy harvest by up to 30% compared to PWM charge controllers and by up to 10% compared to slower MPPT controllers. Advanced Maximum Power Point Detection in case of partial shading conditions If partial shading occurs, two or more maximum power points (MPP) may be present on the powervoltage curve. Conventional MPPTs tend to lock to a local MPP, which may not be the optimum MPP. The innovative SmartSolar algorithm will always maximize energy harvest by locking to the optimum MPP. Outstanding conversion efficiency No cooling fan. Maximum efficiency exceeds 98%. Flexible charge algorithm Fully programmable charge algorithm, and eight pre-programmed algorithms, selectable with a rotary switch (see manual for details). Extensive electronic protection Over-temperature protection and power derating when temperature is high. PV short circuit and PV reverse polarity protection. PV reverse current protection. Bluetooth Smart built-in The wireless solution to set-up, monitor, update and synchronise SmartSolar Charge Controllers. Internal temperature sensor and optional external battery voltage, temperature and current sensing via Bluetooth A Smart Battery Sense, a BMV-712 Smart Battery Monitor or a SmartShunt can be used to communicate battery voltage and temperature (and current, in case of a BMV 712 or a SmartShunt) to one or more SmartSolar Charge Controllers. VE.Direct or VE.Can For a wired data connection to a Color Control GX, other GX products, PC or other devices Fully discharged battery recovery function Will initiate charging even if the battery has been discharged to zero volts. Will reconnect to a fully discharged Li-ion battery with integrated disconnect function. VE.Can: the multiple controller solution Up to 25 units can be synchronised with VE.Can, and up to 10 units with Bluetooth Remote on-off To connect for example to a VE.BUS BMS. Programmable relay Can be programmed to trip on an alarm, or other events. Optional: SmartSolar pluggable LCD display Simply remove the rubber seal that protects the plug on the front of the controller, and plug-in the display Brand Victron Energy Manufacturer Part Number SCC115085512 GTIN 8719076055730 Voltage 12/24V Rated Charge Current 85A Nominal PV Power, 12V 1200W Max. PV Short Circuit Current 70A (max 30A per MC4 conn.) Max. PV Open Circuit Voltage 150V absolute maximum coldest conditions 145V start-up and operating maximum Protection Category IP43 (electronic components), IP22 (connection area) Efficiency 98% Bluetooth Enabled Yes Dimensions H216 x W295 x D103mm Weight 4.5Kg Warranty 5 Years Country of Manufacture India

Read more less

Part No: SIG-STOR-WM-KIT Storage Systems - Wall Bracket Sigenergy Sigenstor Installation Kit for Wall-mounted Max 2 batteries for wall mounting Supplier Part No: SigenStor Installation Kit for Wall-mounted

Read more less

Features Safety and prevention of galvanic corrosion The Isolation Transformer eliminates any electrical continuity between AC shore power and the boat. It is essential for safety and eliminates the need for galvanic isolators and polarity alarms. Safety is taken for granted in case of a normal on-shore installation. A fuse will blow or a GFCI (Ground Fault Current Interrupter) will trip in case of a short circuit or current leakage to ground. Connecting the ground wire of the shore-side supply to the metal parts of the boat will result in galvanic corrosion (see below). Bringing only the live and neutral wire on board results in an unsafe situation because GFCIs will not work nor will a fuse blow in case of a short circuit to a metal part on the boat. Galvanic corrosion occurs when two dissimilar metals in electrical contact are simultaneously exposed to an electrically conducting fluid. Seawater and, to a lesser extent, fresh water are such fluids. In general, the more active alloy of the couple corrodes preferentially while the less active (more noble) material is cathodically protected. The rate of galvanic corrosion is a function of several variables including area ratios, conductivity of the fluid, temperature, nature of the materials, etc. It is a misunderstanding that galvanic corrosion occurs only in metal and aluminium hulls. In fact it can occur on any boat as soon as a metallic part (the shaft and propeller) is in contact with water. Galvanic corrosion will quickly dissolve your sacrificial anodes, and attack the shaft, propeller and other metal parts in contact with water as soon as the boat is connected to the shore-side supply. It might therefore be tempting not to connect the ground conductor: this is however extremely dangerous because GFCIs will not work nor will a fuse blow in case of a short circuit to a metal part on the boat. The best solution to avoid galvanic corrosion and at the same time prevent any unsafe situation is to install an Isolation Transformer to connect to the shore-side supply. The Isolation Transformer eliminates any electrical continuity between shore power and the boat. The shore power is fed to the primary side of the transformer and the ship is connected to the secondary. The Isolation Transformer completely isolates the boat from the shore ground. By connecting all metal parts to the neutral output on the secondary side of the transformer, a GFCI will trip or a fuse will blow in case of a short circuit. Soft start is a standard feature of a Victron Energy isolation transformer. It will prevent the shore power fuse from blowing due to the inrush current of the transformer, which would otherwise occur. It is also recommended, for optimal safety, to connect the secondary neutral of the transformer to ground when the boat is out of the water. Brand Victron Energy Manufacturer Part Number ITR040362041 Input 115 or 230 V Output 115 or 230 V Frequency 50/60 Hz Rating 32 / 16 A Soft Start Yes Transformer Type Toroidal (low noise, low weight) Input Circuit Breaker Yes Protection Category IP21 Dimensions H362 x W258 x D218mm Weight (kg) 23 Warranty 5 Years

Read more less

Models: 3000VA, 5000VA, 8000VA, 10000VA, 15000VA Two AC Inputs & two AC Outputs The Quattro can be connected to two independent AC sources, for example shore-side power and a generator, or two generators. The Quattro will automatically connect to the active source. The main output has no-break functionality. In the event of a grid failure, or shore or generator power being disconnected, the Quattro takes over the supply to the connected loads. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption. The second output is live only when AC is available on one of the inputs of the Quattro. Loads that should not discharge the battery, such as air-conditioning or a water heater can be connected to this output. Unique PowerAssist feature The Quattro will prevent overload of a limited AC source, such as a generator or shore power connection. First, battery charging will automatically be reduced when otherwise an overload would occur. The second level will boost the output of a generator or shore side supply with power taken from the battery. Virtually unlimited power thanks to parallel operation Up to 6 Quattros can operate in parallel to achieve higher power output. Three phase or split phase operation is also possible. Please check our datasheets to see which models have paralleling, three phase and split phase capabilities. Remote Monitoring and Control Monitor and control your Quattro and system or systems’ locally (LAN) or remotely via the internet from anywhere in the world, using the free VRM app and free VRM portal website. Access can be from a phone, tablet, laptop or PC for multiple operating systems. There is no end to the level of control, via the required Color Control GX or Venus GX, from adjusting your Quattro to setting a Geofence for hire vehicles and more… Two AC inputs with integrated transfer switch The Quattro can be connected to two independent AC sources, for example the public grid and a generator, or two generators. The Quattro will automatically connect to the active source. Two AC Outputs The main output has no-break functionality. The Quattro takes over the supply to the connected loads in the event of a grid failure or when shore/generator power is disconnected. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption.The second output is live only when AC is available on one of the inputs of the Quattro. Loads that should not discharge the battery, like a water heater for example, can be connected to this output. Virtually unlimited power thanks to parallel operation Up to 6 Quattro units can operate in parallel. Six units 48/10000/140, for example, will provide 48kW / 60kVA output power and 840 Amps charging capacity. Split phase options Two units can be stacked to provide 120-0-120V, and additional units can be paralleled up to a total of 6 units per phase, to supply up to 30kW / 36kVA of split phase power.Alternatively, a split phase AC source can be obtained by connecting our autotransformer (see data sheet on www.victronenergy.com) to a ‘European’ inverter programmed to supply 240V / 60Hz. Three phase capability Three units can be configured for three phase output. But that’s not all: up to 6 sets of three units can be parallel connected to provide 144kW / 180kVA inverter power and more than 2500A charging capacity. PowerControl – Dealing with limited generator, shore side or grid power The Quattro is a very powerful battery charger. It will therefore draw a lot of current from the generator or shore side supply (16A per 5kVA Quattro at 230VAC). A current limit can be set on each AC input. The Quattro will then take account of other AC loads and use whatever is spare for charging, thus preventing the generator or mains supply from being overloaded. PowerAssist – Boosting shore or generator power This feature takes the principle of PowerControl to a further dimension allowing the Quattro to supplement the capacity of the alternative source. Where peak power is so often required only for a limited period, the Quattro will make sure that insufficient mains or generator power is immediately compensated for by power from the battery. When the load reduces, the spare power is used to recharge the battery. Solar energy: AC power available even during a grid failure The Quattro can be used in off grid as well as grid connected PV and other alternative energy systems.Loss of mains detection software is available. System configuring In case of a stand-alone application, if settings have to be changed, this can be done in a matter of minutes with a DIP switch setting procedure. Parallel and three phase applications can be configured with VE.Bus Quick Configure and VE.Bus System Configurator software. Off grid, grid interactive and self-consumption applications, involving grid-tie inverters and/or MPPT Solar Chargers can be configured with Assistants (dedicated software for specific applications). On-site Monitoring and control Several options are available: Battery Monitor, Multi Control Panel, Color Control GX or other GX devices, smartphone or tablet (Bluetooth Smart), laptop or computer (USB or RS232). Remote Monitoring and control Color Control GX or other GX devices.Data can be stored and displayed on our VRM (Victron Remote Management) website, free of charge. Remote configuring When connected to the Ethernet, systems with a Color Control GX or other GX device can be accessed and settings can be changed remotely.   Weight 34 kg Dimensions 280 × 350 × 470 mm Brand Victron Energy Input Voltage 12V Output Voltage 110V Current (Amps) 200A Wattage (W) 4000W Region North America Inverter Type Pure Sine Wave Warranty 5 Years

Read more less

Features of the Phoenix 48/3000 Smart Bluetooth built-in: fully configurable with a tablet or smartphone Low battery voltage alarm Low battery voltage cut-off and restart levels Dynamic cut-off: load dependent cut-off level Output voltage: 210 – 245V Frequency: 50 Hz or 60 Hz ECO mode on/off and ECO mode sense level Alarm relay Monitoring: In- and output voltage, load and alarms VE.Direct communication port The VE.Direct port can be connected to a computer (VE.Direct to USB interface cable needed) to configure and monitor the same parameters. Proven reliability The full bridge plus toroidal transformer topology has proven its reliability over many years. The inverters are short circuit proof and protected against overheating, whether due to overload or high ambient temperature. High start-up power Needed to start loads such as power converters for LED lamps, halogen lamps or electric tools. ECO mode When in ECO mode, the inverter will switch to standby when the load decreases below a preset value. Once in standby the inverter will switch on for a short period every 2,5 seconds (adjustable). If the load exceeds the preset level, the inverter will remain on. Remote on/off A remote on/off switch or relay contact can be connected to a two pole connector. Alternatively, the H terminal (left) of the two pole connector can be switched to battery plus, or the L terminal (right) of the two pole connector can be switched to battery minus (or the chassis of a vehicle, for example). To transfer the load to another AC source: the automatic transfer switch For our low power inverters we recommend our Filax Automatic Transfer Switch. The Filax features a very short switchover time (less than 20 milliseconds) so that computers and other electronic equipment will continue to operate without disruption. Alternatively use a MultiPlus with built-in transfer switch Brand Victron Energy Manufacturer Part Number PIN482300000 gtin 8719076047384 Voltage 48V Cont. Output Power at 25°C 3000VA Peak Power 6000W Output AC Voltage 230V Efficiency 95% Protection Category IP21 Dimensions H485 x W285 x D150mm Weight 19Kg Warranty 5 Years Bluetooth Enabled Yes Country of Manufacture China

Read more less

Features Perfect chargers for any type of battery Charge voltage can be precisely adjusted to suit any sealed or unsealed battery system. In particular, sealed maintenance free batteries must be charged correctly in order to ensure a long service life. Overvoltage will result in excessive gassing and venting of a sealed battery. The battery will dry out and fail. Suitable for AC and DC supply (AC-DC and DC-DC operation) Except for the 3-phase input models, the chargers also accept a DC supply. Controlled charging Every TG Charger has a microprocessor, which accurately controls the charging in three steps. The charging process takes place in accordance with the IUoUo characteristic and charges more rapidly than other processes. Use of TG Chargers as a power supply As a result of the perfectly stabilized output voltage, a TG Charger can be used as a power supply if batteries or large buffer capacitors are not available. Two outputs to charge 2 battery banks (24V models only) The TG Chargers feature 2 isolated outputs. The second output, limited to approximately 4A and with a slightly lower output voltage, is intended to top up a starter battery. To increase battery life: temperature compensation Every Skylla TG Charger comes with a battery temperature sensor. When connected, charge voltage will automatically decrease with increasing battery temperature. This feature is especially recommended for sealed batteries which otherwise might be overcharged and dry out due to venting. Battery voltage sense In order to compensate for voltage loss due to cable resistance, TG Chargers are provided with a voltage sense facility so that the battery always receives the correct charge voltage. Brand Victron Energy Manufacturer Part Number SDTG4800501 Voltage 48 Charger Current House Battery 50A Charger Current Starter Battery N.A. Recommended Battery Capacity 250 – 500Ah Battery Connection M8 Studs Outputs 1 Temperature Sensor Yes Can Be Used As Power Supply Yes IP Rating IP21 Dimensions H365 x W250 x D257mm Weight (kg) 10 Warranty 5 Years

Read more less

Features Ultra-fast Maximum Power Point Tracking (MPPT) Especially in case of a clouded sky, when light intensity is changing continuously, an ultra-fast MPPT controller will improve energy harvest by up to 30% compared to PWM charge controllers and by up to 10% compared to slower MPPT controllers. Advanced Maximum Power Point Detection in case of partial shading conditions If partial shading occurs, two or more maximum power points (MPP) may be present on the powervoltage curve. Conventional MPPTs tend to lock to a local MPP, which may not be the optimum MPP. The innovative SmartSolar algorithm will always maximize energy harvest by locking to the optimum MPP. Outstanding conversion efficiency No cooling fan. Maximum efficiency exceeds 98%. Flexible charge algorithm Fully programmable charge algorithm, and eight pre-programmed algorithms, selectable with a rotary switch (see manual for details). Extensive electronic protection Over-temperature protection and power derating when temperature is high. PV short circuit and PV reverse polarity protection. PV reverse current protection. Bluetooth Smart built-in The wireless solution to set-up, monitor, update and synchronise SmartSolar Charge Controllers. Internal temperature sensor and optional external battery voltage, temperature and current sensing via Bluetooth A Smart Battery Sense, a BMV-712 Smart Battery Monitor or a SmartShunt can be used to communicate battery voltage and temperature (and current, in case of a BMV 712 or a SmartShunt) to one or more SmartSolar Charge Controllers. VE.Direct or VE.Can For a wired data connection to a Color Control GX, other GX products, PC or other devices Fully discharged battery recovery function Will initiate charging even if the battery has been discharged to zero volts. Will reconnect to a fully discharged Li-ion battery with integrated disconnect function. VE.Can: the multiple controller solution Up to 25 units can be synchronised with VE.Can, and up to 10 units with Bluetooth Remote on-off To connect for example to a VE.BUS BMS. Programmable relay Can be programmed to trip on an alarm, or other events. Optional: SmartSolar pluggable LCD display Simply remove the rubber seal that protects the plug on the front of the controller, and plug-in the display Brand Victron Energy Manufacturer Part Number SCC115110411 GTIN 8719076050353 Voltage 12/24/48V Rated Charge Current 100A Nominal PV Power, 12V 1450W Max. PV Short Circuit Current 70A Max. PV Open Circuit Voltage 150V absolute maximum coldest conditions 145V start-up and operating maximum Protection Category IP43 (electronic components), IP22 (connection area) Efficiency 98% Bluetooth Enabled Yes Dimensions H216 x W295 x D103mm Weight 4.5Kg Warranty 5 Years

Read more less

Features Two AC Outputs The main output has no break functionality. The MultiPlus takes over the supply to the connected loads in the event of a grid failure or when shore/generator power is disconnected. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption. The second output is live only when AC is available on the input of the MultiPlus. Loads that should not discharge the battery, like a water heater for example can be connected to this output (second output available on models rated at 3 kVA and more). Virtually unlimited power thanks to parallel operation Up to 6 Multis can operate in parallel to achieve higher power output. Six 24/5000/120 units, for example, will provide 25 kW / 30 kVA output power with 720 Amps charging capacity. Three phase capability In addition to parallel connection, three units of the same model can be configured for three phase output. But that’s not all: up to 6 sets of three units can be parallel connected for a huge 75 kW / 90 kVA inverter and more than 2000 Amps charging capacity. PowerControl – Dealing with limited generator, shore side or grid power The MultiPlus is a very powerful battery charger. It will therefore draw a lot of current from the generator or shore side supply (nearly 10 A per 5 kVA Multi at 230 VAC). With the Multi Control Panel a maximum generator or shore current can be set. The MultiPlus will then take account of other AC loads and use whatever is extra for charging, thus preventing the generator or shore supply from being overloaded. PowerAssist – Boosting the capacity of shore or generator power This feature takes the principle of PowerControl to a further dimension. It allows the MultiPlus to supplement the capacity of the alternative source. Where peak power is so often required only for a limited period, the MultiPlus will make sure that insufficient shore or generator power is immediately compensated for by power from the battery. When the load reduces, the spare power is used to recharge the battery. Solar energy: AC power available even during a grid failure The MultiPlus can be used in off grid as well as grid connected PV and other alternative energy systems. Loss of mains detection software is available. System configuring In case of a stand-alone application, if settings have to be changed, this can be done in a matter of minutes with a DIP switch setting procedure. Parallel and three phase applications can be configured with VE.Bus Quick Configure and VE.Bus System Configurator software. Brand Victron Energy Manufacturer Part Number CMP248010000 Voltage 24 Transfer Switch (A) 16 Cont. Output Power at 25°C (VA) 800 Peak Power (W) 1600 Max Efficiency 94% Zero Load Power (W) 10 Charge Current House Battery (A) 16 Charge Current Starter Battery (A) 4 (12 V and 24 V models only) Battery Temperature Sensor Yes Programmable Relay Yes Remote on-off Yes Protection Category IP21 Dimensions H375 x W214 x D110mm Weight (kg) 10 Warranty 5 Years Country of Manufacture China

Read more less

The Lynx Power In (M10) is a modular DC busbar, used to connect batteries to the Victron Energy Lynx DC distribution system. The Lynx DC distribution system is a modular busbar system that incorporates DC connections, power distribution, fusing and battery monitoring. The Lynx Power In (M10) can be used on its own as a standalone battery connection system, or it can be combined with the other Lynx (M10) modules in the range to form a modular system to suit your specific needs. Inside the Lynx Power In (M10) there is a positive and negative busbar with 4 connections for batteries, loads or chargers, and a ground connection. Multiple Power In modules can be connected together to form a longer busbar providing more connection points. Note that the Power In does not contain any fuses so if used on its own, cable connections to all batteries, charging sources and loads must be fused externally (download the user manual from the Manuals & Guides tab for system examples). This unit has a nominal current rating of 1000A for 12V, 24V or 48V systems, and M10 module connection bars and studs. Specifications Manuals & Guides Customer Reviews (0) Victron Energy is at the cutting edge of power management technology, offering a range of innovative and highly reliable products for every leisure application. This highly respected brand has a wealth of experience in the automotive, industrial, off-grid, marine, energy-storage and telecoms sectors.

Read more less

  Brand Victron Energy Manufacturer Part Number SCC010020060 GTIN 8719076046219 Battery Voltage 12/24 V with automatic system voltage detection [for LiFePO4 no automatic system voltage detection] Rated Charge Current 20A Second battery output Yes Load Output 2 USB ports 5V/2A Grounding Common negative Battery Temperature Sensor Yes, remote sensor [included] Protection Category IP20 Dimensions H101.5 x W184.0 x D47.1mm Weight 0.3Kg Warranty 5 Years

Read more less

ESS Kit – Victron Energy 4kW Kit with 2.8kW Solar Array, 5000VA EasySolar-II and 10.2kWh TN Power Li-PO4 Battery Do you want to be more independent and not worry about utility prices then our Energy Storage Solution kits are perfect for you. Using a combination of Victron equipment and lithium battery storage these kits are flexible and professional grade to allow you to be less reliant on the grid. All our kits are professionally mounted on a fireproof board and supplied with industry leading lithium batteries all you need to do is connect to the mains and mount and connect the supplied solar panels. Kit contains the below products and we have included links to each product too so you can see the individual specifications: 8x Victron Energy Solar Panel 360W Mono with Mounting Kit 2x TN Power 48V 100Ah Heated Lithium Battery 1x Victron Energy EasySolar Inverter Charger 48/5000 MPPT 250/100 1x Victron Energy Lynx Distributor 1x Victron Energy RJ45 5m Cable 4m 50mm2 Cable Red 4m 50mm2 Cable Black 8x T50-8 Copper Tube Lug 1x Victron Energy Interface MK3-USB 1x Victron Energy VE.Direct Cable 1.8m 1x Victron Energy VE.Can to CAN-Bus Type B Cable 5m 1x IMO DC PV Isolator Switch 1x Victron Energy SolarCable 6mm2 20m 2x Victron Energy Solar Splitter Pair MC4 (1M-2F / 2M-1F) 1x Victron Energy 58V 125A MEGA-Fuse 1x Victron Energy 58V 200A MEGA-Fuse

Read more less

The Victron Orion-Tr Smart 48/24-16A (380W) Isolated DC-DC Charger is a rugged and reliable power supply solution, allowing efficient voltage conversion from 48V to 24V for various applications. It provides a stable and adjustable output voltage, ensuring compatibility with a wide range of DC-powered devices and systems. With its remote on/off functionality, the unit can be controlled via a low-power switch or integrated into an engine run/stop circuit. Its robust protection mechanisms, including short circuit and high-temperature protection, ensure safe and reliable operation in demanding environments. The Orion-Tr Smart 48/24-16A is not intended for battery charging but excels in applications requiring a steady 24V power source. It is ideal for industrial, automotive, marine, and off-grid installations where precise voltage regulation and high efficiency are critical. With its compact design, efficient power conversion, and safety features, the Victron Orion-Tr Smart 48/24-16A is a high-performance solution for reliable 24V power in 48V systems. Remote On-Off Control – Can be operated with a low-power switch or engine run/stop switch, eliminating the need for a high-current switch in the input wiring. Short Circuit Protection – Fully short circuit proof, preventing damage from electrical faults. Parallel Operation – Unlimited units can be connected in parallel to increase output power. High-Temperature Protection – Automatically reduces output current in high ambient temperatures. IP43 Protection – Dust and water-resistant when installed with screw terminals oriented downward. Screw Terminals – Allows tool-free installation with secure connections. Adjustable Output Voltage – 20V to 30V (not intended for battery charging). Galvanic Isolation – 200V DC isolation between input, output, and casing for enhanced safety. Brand Victron Energy DC Connection Screw Terminals Input Voltage Range 32-70 V Manufacturer Part Number ORI482438120

Read more less

Features Bluetooth Smart enabled Any Bluetooth enabled smart phone, tablet or other device can be used to monitor, to change settings and to update the charger when new software features become available.   Phoenix Smart (1+1): two outputs to charge 2 battery banks The second output, limited to approximately 3A and with a slightly lower output voltage, is intended to top up a starter battery.   Automatic voltage compensation The charger compensates for voltage drop over the DC cabling by slightly increasing output voltage when the DC current increases. Please see the manual for details.   Adaptive 5-stage charge algorithm: bulk – absorption – recondition – float – storage The Phoenix Smart Charger features our well-known ‘adaptive’ battery management system that can be preset to suit different types of batteries. The ‘adaptive’ feature will automatically optimise the charge process relative to the way the battery is being used.   The right amount of charge: variable absorption time When only shallow discharges occur (a yacht connected to shore power for example) the absorption time is kept short in order to prevent overcharging of the battery. After a deep discharge the absorption time is automatically increased to make sure that the battery will be fully charged.   Also charges Li-ion (LiFePO4) batteries Charger on-off control can be implemented by connecting a relay or open collector optocoupler output from a Li-ion BMS to the remote on-off port. Alternatively full control of voltage and current can be achieved with Bluetooth.   Fully programmable charge algorithm The charge algorithm can be programmed with help of Bluetooth or the VE.Direct interface. Three preprogrammed algorithms can be selected with the mode button (see specifications).   Remote on-off The remote on/off consists of two terminals: Remote H and Remote L. A remote on/off switch or relay contact can be connected between H and L. Alternatively, terminal H can be pulled high, or terminal L can be pulled low.   VE.Direct interface For a wired data connection to a Color Control panel, PC or other devices. Please see the VictronConnect app under Downloads / Software on our website.   Programmable relay Can be programmed using the VE.Direct interface or a Bluetooth enabled device to trip on an alarm or other events. Brand Victron Energy Manufacturer Part Number PSC125051085 Voltage 12V Charger Current House Battery 50A Low Current Mode 25A Efficiency 92% Outputs 1+1 IP Rating IP43 (electronic components), IP22 (connection area) Dimensions H180 x W249 x D100mm Weight 3.5Kg Warranty 5 Years

Read more less

The isolator is installed directly behind your boat’s 230V connection. The forward voltage from the galvanic isolator is higher than the potential difference between metals. As a result, this voltage will not allow conduction and as such, the galvanic isolator will prevent any electrolytic current. However, if there is a (higher) error voltage in the AC circuit, the diodes will allow current through and the residual-current device will break the circuit. Brand Victron Energy Manufacturer Part Number GDI000032000 Peak Current (20 ms) 3200 A Maximum Current 32 A Connection M6 IP Rating IP67 Dimensions H63 x W164 x D200mm Weight (kg) 2 Warranty 5 Years

Read more less

When they are connected in this way, the diodes allow current in both directions but only above a certain threshold voltage. The voltage at which diodes conduct is about 1.4 Vdc. The isolator is installed directly behind your boat’s 230V connection. The forward voltage from the galvanic isolator is higher than the potential difference between metals. As a result, this voltage will not allow conduction and as such, the galvanic isolator will prevent any electrolytic current. However, if there is a (higher) error voltage in the AC circuit, the diodes will allow current through and the residual-current device will break the circuit. Brand Victron Energy Manufacturer Part Number GDI000064000 Peak Current (20 ms) 6000 A Maximum Current 64 A Connection M6 IP Rating IP67 Dimensions H63 x W164 x D335mm Weight (kg) 3.2 Warranty 5 Years

Read more less

Features of the Phoenix Smart IP43 Charger 12/50(3)  Bluetooth Smart enabled Any Bluetooth enabled smart phone, tablet or other device can be used to monitor, to change settings and to update the charger when new software features become available. Adaptive 5-stage charge algorithm: bulk – absorption – recondition – float – storage The Phoenix Smart IP43 charger features our well-known ‘adaptive’ battery management system that can be pre-set to suit different types of batteries. The ‘adaptive’ feature will automatically optimise the charge process relative to the way the battery is being used.   The right amount of charge: variable absorption time When only shallow discharges occur (a yacht connected to shore power for example) the absorption time is kept short in order to prevent overcharging of the battery. After a deep discharge the absorption time is automatically increased to make sure that the battery will be fully charged.   Preventing damage due to excessive gassing: the BatterySafe mode If, in order to quickly charge a battery, a high charge current in combination with a high absorption voltage has been chosen, the charger will prevent damage due to excessive gassing by automatically limiting the rate of voltage increase once the gassing voltage has been reached   Less maintenance and aging when the battery is not in use: the Storage Mode The Storage Mode kicks in whenever the battery has not been subjected to discharge during 24 hours. In the Storage Mode float voltage is reduced to 2,2 V/cell (13,2 V for a 12 V battery) to minimise gassing and corrosion of the positive plates. Once a week the voltage is raised back to the absorption level to ‘equalize’ the battery. This feature prevents stratification of the electrolyte and sulphation, a major cause of early battery failure.   Brand Victron Energy Manufacturer Part Number PSC125053095 gtin 8719076053514 Voltage 12V Charge Current 50A Input Voltage 85-265VAC Number of Outputs 3 Protection Category Electronic components: IP43, Connection area: IP22 Efficiency 94% Bluetooth Enabled Yes Dimensions H180 x W249 x D116mm Weight 2.7Kg Warranty 5 Years Country of Manufacture Malaysia

Read more less

FeaturesUltrafast Maximum Power Point Tracking (MPPT)Especially in case of a clouded sky, when light intensity is changing continuously, an ultra-fast MPPT controller will improve energy harvest by up to 30% compared to PWM charge controllers and by up to 10% compared to slower MPPT controllers.Advanced Maximum Power Point Detection in case of partial shading conditionsIf partial shading occurs, two or more maximum power points may be present on the power-voltage curve. Conventional MPPTs tend to lock to a local MPP, which may not be the optimum MPP. The innovative BlueSolar algorithm will always maximize energy harvest by locking to the optimum MPP.Outstanding conversion efficiencyNo cooling fan. Maximum efficiency exceeds 98%. The full output current up to 40°C (104°F).Flexible charge algorithmFully programmable charge algorithm (see the software page on our website), and eight pre-programmed algorithms, selectable with a rotary switch (see manual for details).Extensive electronic protectionOver-temperature protection and power derating when temperature is high. PV short circuit and PV reverse polarity protection. PV reverse current protection.Internal temperature sensorCompensates absorption and float charge voltage for temperature.Real-time data display options- ColorControl GX or other GX devices: see the Venus documents on our website.- A smartphone or other Bluetooth-enabled device: VE.Direct Bluetooth Smart dongle needed.

Read more less

Liquid crystal display For status monitoring and set-up Day/night timing of the load output This option allows for a pre-set ON-time after dusk. Programmable battery charge algorithm Preprogrammed algorithms for AGM, GEL, Flooded or LiFePO4 batteries (with internal BMS only) Two 5 Volt USB outputs Maximum current (both outputs combined): 2A Brand Victron Energy Manufacturer Part Number SCC040010050 GTIN 8719076046233 Battery Voltage 48V Rated Charge Current 10A Maximum Solar Voltage 100V Load Output Manual control + low voltage disconnect + timer Grounding Common positive IP Rating IP20 Dimensions H101 x W184 x D47mm Weight 0.3Kg Warranty 5 Years

Read more less

The supply could be the grid, a generator or two stacked inverters. Some of the loads connected are 240V, others are 120V. On each 120V leg the load should not exceed 30A. The problem is that as soon as 120V loads are connected, the two legs will show a different current. This is because the 120V loads on the two legs will never be balanced. A 120V 1200W hairdryer, for example, will draw 10A from one leg. A 120V washing machine could even draw in excess of 20A from one leg. Between the two legs the difference in current, or current unbalance, will therefore often be 20A or more. This means that the 30A supply will not be used up to its full potential. By the time one leg draws 30A, the other leg may be drawing no more than 10A, and increasing the 240V load, for example, will result in an overload of one leg while the other leg still has spare capacity. Theoretically, the total power that can be drawn from a 30A 120/240V supply is 30 x 240 = 7,2 kVA. In case of 20A unbalance, the practical maximum will be 30 x 120 + 10 x120 = 4,8kVA, or 67% of the theoretical maximum. The solution is an Autotransformer. By leaving the neutral of the split phase supply unused, and connecting an Autotransformer to create a new neutral, as shown in figure 1, any load unbalance is ‘absorbed’ by the Autotransformer. In case of a 30A supply, the load can be increased to 7,2kVA, and a 20A load unbalance will result in one leg supplying 40A, and the other leg 20A. The 20A difference will flow through the neutral and the windings of the Autotransformer. The current through both 120V wires of the split phase supply will be 30A. Brand Victron Energy Manufacturer Part Number ITR000100101 Input/Output Voltage 120/240V Input Circuit Breaker 100A, two pole Frequency (Hz) 50/60 Maximum 240V feed through current 100A Ingress Protection IP21 Dimensions (Including Terminals) H425 x W214 x D110 mm Weight (kg) 13.5 Warranty 5 Years

Read more less