Quick Order

Brand Victron Energy Manufacturer Part Number ASS030510120 Warranty 5 Years

Read more less

Features VRLA technology VRLA stands for Valve Regulated Lead Acid, which means that the batteries are sealed. Gas will escape through the safety valves only in case of overcharging or cell failure. VRLA batteries are maintenance free for life.   Sealed (VRLA) GEL Batteries Here the electrolyte is immobilized as gel. Gel batteries in general have a longer service life and better cycle capacity than AGM batteries.   Low Self-Discharge Because of the use of lead calcium grids and high purity materials, Victron VRLA batteries can be stored during long periods of time without recharge. The rate of self-discharge is less than 2% per month at 20°C. The self-discharge doubles for every increase in temperature by 10°C. Victron VRLA batteries can therefore be stored for up to a year without recharging, if kept under cool conditions.   Exceptional Deep Discharge Recovery Victron VRLA batteries have exceptional discharge recovery, even after deep or prolonged discharge. Nevertheless repeatedly deep and prolonged discharge has a very negative effect on the service life of all lead acid batteries, Victron batteries are no exception.   Battery Discharging Characteristics The rated capacity of Victron AGM and Gel Deep Cycle batteries refers to 20 hour discharge, in other words: a discharge current of 0,05 C. The rated capacity of Victron Tubular Plate Long Life batteries refers to 10 hours discharge. The effective capacity decreases with increasing discharge current (see table 1). Please note that the capacity reduction will be even faster in case of a constant power load, such as an inverter.   Brand Victron Energy Manufacturer Part Number BAT412800104 Voltage 12 Capacity (C20) 90 Cold Cranking (EN) 360 Terminal Type M8 Terminal Layout LH+ Dimensions (Including Terminals) L350 x W167 x H183mm Weight (kg) 26 Warranty 2 Years Battery Technology Gel Battery Application Deep Cycle

Read more less

Brand Victron Energy Manufacturer Part Number BPC900520014 GTIN 8719076051343 Warranty 5 Years

Read more less

    Brand Victron Energy Manufacturer Part Number BPC900120114 Voltage 6-15 Maximum Current 30 A Cable Length 0.3m Protection Category IP65 Dimensions L22 x W18 x H55mm Weight (kg) 0.17 Warranty 5 Years

Read more less

Features Bluetooth Smart The Blue Smart IP22 Charger is the wireless solution to monitor voltage and current, to change settings and to update the charger when new features become available. High efficiency With up to 94% efficiency, these chargers generate up to four times less heat when compared to the industry standard. And once the battery is fully charged, power consumption reduces to 0,5 Watt, some five to ten times better than the industry standard. Adaptive 6-stage charge algorithm: test – bulk – absorption – recondition – float – storage The Blue Smart Charger features a microprocessor controlled ‘adaptive’ battery management. The adaptive feature will automatically optimize the charging process relative to the way the battery is being used. Storage Mode: less maintenance and aging when the battery is not in use The storage mode kicks in whenever the battery has not been subjected to discharge during 24 hours. In the storage mode float voltage is reduced to 2,2V/cell (13,2V for a 12V battery) to minimize gassing and corrosion of the positive plates. Once a week the voltage is raised back to the absorption level to ‘equalize’ the battery. This feature prevents stratification of the electrolyte and sulfation, a major cause of early battery failure. Also charges Li-ion (LiFePO4) batteries LiFePO4 batteries are charged with a simple bulk – absorption – float algorithm. NIGHT and LOW setting When in NIGHT or LOW mode, the output current is reduced to max. 50% of the nominal output and the charger will be totally noiseless. The NIGHT mode automatically ends after 8 hours. The LOW mode can be ended manually. Protected against overheating Output current will reduce as temperature increases up to 50°C, but the Blue Smart Charger will not fail. Eleven LEDs for status indication Charge algorithm: TEST / BULK / ABSORPTION / RECONDITION / FLOAT / STORAGE / READY. MODE button to set: NORMAL (14,4V) / HIGH (14,7V) / RECONDITION / LI-ION. Brand Victron Energy Manufacturer Part Number BPC123047022 Voltage 12 Charger Amps 30A Outputs 1 Efficiency 93% Plug Type UK IP Rating IP22 Dimensions H235 x W108 x D65mm Weight 1.3Kg Warranty 5 Years

Read more less

Features Bluetooth Smart The Blue Smart IP22 Charger is the wireless solution to monitor voltage and current, to change settings and to update the charger when new features become available. High efficiency With up to 94% efficiency, these chargers generate up to four times less heat when compared to the industry standard. And once the battery is fully charged, power consumption reduces to 0,5 Watt, some five to ten times better than the industry standard. Adaptive 6-stage charge algorithm: test – bulk – absorption – recondition – float – storage The Blue Smart Charger features a microprocessor controlled ‘adaptive’ battery management. The adaptive feature will automatically optimize the charging process relative to the way the battery is being used. Storage Mode: less maintenance and aging when the battery is not in use The storage mode kicks in whenever the battery has not been subjected to discharge during 24 hours. In the storage mode float voltage is reduced to 2,2V/cell (13,2V for a 12V battery) to minimize gassing and corrosion of the positive plates. Once a week the voltage is raised back to the absorption level to ‘equalize’ the battery. This feature prevents stratification of the electrolyte and sulfation, a major cause of early battery failure. Also charges Li-ion (LiFePO4) batteries LiFePO4 batteries are charged with a simple bulk – absorption – float algorithm. NIGHT and LOW setting When in NIGHT or LOW mode, the output current is reduced to max. 50% of the nominal output and the charger will be totally noiseless. The NIGHT mode automatically ends after 8 hours. The LOW mode can be ended manually. Protected against overheating Output current will reduce as temperature increases up to 50°C, but the Blue Smart Charger will not fail. Eleven LEDs for status indication Charge algorithm: TEST / BULK / ABSORPTION / RECONDITION / FLOAT / STORAGE / READY. MODE button to set: NORMAL (14,4V) / HIGH (14,7V) / RECONDITION / LI-ION. Brand Victron Energy Manufacturer Part Number BPC241242022 Voltage 24 Charger Amps 12 Efficiency 94% Outputs 1 Plug Type UK IP Rating IP22 Dimensions H235 x W108 x D65mm Weight (kg) 1.3 Warranty 5 Years

Read more less

Features   Bluetooth Smart The Blue Smart IP22 Charger is the wireless solution to monitor voltage and current, to change settings and to update the charger when new features become available.   High efficiency With up to 94% efficiency, these chargers generate up to four times less heat when compared to the industry standard. And once the battery is fully charged, power consumption reduces to 0,5 Watt, some five to ten times better than the industry standard.   Adaptive 6-stage charge algorithm: test – bulk – absorption – recondition – float – storage The Blue Smart Charger features a microprocessor controlled ‘adaptive’ battery management. The adaptive feature will automatically optimize the charging process relative to the way the battery is being used.   Storage Mode: less maintenance and aging when the battery is not in use The storage mode kicks in whenever the battery has not been subjected to discharge during 24 hours. In the storage mode float voltage is reduced to 2,2V/cell (13,2V for a 12V battery) to minimize gassing and corrosion of the positive plates. Once a week the voltage is raised back to the absorption level to ‘equalize’ the battery. This feature prevents stratification of the electrolyte and sulfation, a major cause of early battery failure.   Also charges Li-ion (LiFePO4) batteries LiFePO4 batteries are charged with a simple bulk – absorption – float algorithm.   NIGHT and LOW setting When in NIGHT or LOW mode, the output current is reduced to max. 50% of the nominal output and the charger will be totally noiseless. The NIGHT mode automatically ends after 8 hours. The LOW mode can be ended manually.   Protected against overheating Output current will reduce as temperature increases up to 50°C, but the Blue Smart Charger will not fail.   Eleven LEDs for status indication Charge algorithm: TEST / BULK / ABSORPTION / RECONDITION / FLOAT / STORAGE / READY. MODE button to set: NORMAL (14,4V) / HIGH (14,7V) / RECONDITION / LI-ION. Brand Victron Energy Manufacturer Part Number BPC241648022 GTIN 8719076052531 Voltage 24 Charger Amps 16A Outputs 3 Efficiency 94% Plug Type UK IP Rating IP22 Dimensions H235 x W108 x D65mm Weight 1.3Kg Warranty 5 Years

Read more less

Features Quality without compromise Aluminium epoxy powder coated cases with drip shield and stainless steel fixings withstand the rigors of an adverse environment: heat, humidity and salt air. Circuit boards are protected with an acrylic coating for maximum corrosion resistance. Temperature sensors ensure that power components will always operate within specified limits, if needed by automatic reduction of output current under extreme environmental conditions.   Universal 90-265V AC input voltage range and also suitable for DC supply (AC-DC and DC-DC operation) All models will operate without any adjustment needed over a 90 to 265 Volt input voltage range, whether 50 Hz or 60 Hz. The chargers also accept a 90-400 V DC supply.   Three outputs that each can supply the full output current Three isolated outputs to simultaneously charge 3 battery banks. Each output is capable to supply the full rated current.   Three-stage charging, with temperature compensation The Centaur charges at bulk rate until the output has reduced to 70% of the rated Amps, at which a 4 hour timer begins. After the timed period the charger switches to float rate. An internal temperature sensor is used to compensate the charge voltage with – 2 mV/ºC (– 1 mV/ºF) per cell. A DIP switch is available to select the optimum charge/float voltages for Flooded Lead-acid, Gel or AGM batteries. Brand Victron Energy Manufacturer Part Number CCH012020000 Voltage 12 Charger Amps 20 Outputs 3 Recommended Battery Capacity 80 – 200Ah Battery Connection M6 Studs IP Rating IP20 Dimensions H355 x W215 x D110mm Weight (kg) 3.8 Warranty 5 Years

Read more less

Features Quality without compromise Aluminium epoxy powder coated cases with drip shield and stainless steel fixings withstand the rigors of an adverse environment: heat, humidity and salt air. Circuit boards are protected with an acrylic coating for maximum corrosion resistance. Temperature sensors ensure that power components will always operate within specified limits, if needed by automatic reduction of output current under extreme environmental conditions. Universal 90-265V AC input voltage range and also suitable for DC supply (AC-DC and DC-DC operation) All models will operate without any adjustment needed over a 90 to 265 Volt input voltage range, whether 50 Hz or 60 Hz. The chargers also accept a 90-400 V DC supply. Three outputs that each can supply the full output current Three isolated outputs to simultaneously charge 3 battery banks. Each output is capable to supply the full rated current. Three-stage charging, with temperature compensation The Centaur charges at bulk rate until the output has reduced to 70% of the rated Amps, at which a 4 hour timer begins. After the timed period the charger switches to float rate. An internal temperature sensor is used to compensate the charge voltage with – 2 mV/ºC (– 1 mV/ºF) per cell. A DIP switch is available to select the optimum charge/float voltages for Flooded Lead-acid, Gel or AGM batteries Brand Victron Energy Manufacturer Part Number CCH012030000 Voltage 12 Charger Amps 30 Outputs 3 Recommended Battery Capacity 120 – 300Ah Battery Connection M6 Studs IP Rating IP20 Dimensions H355 x W215 x D110mm Weight (kg) 3.8 Warranty 5 Years

Read more less

Features Quality without compromise Aluminium epoxy powder coated cases with drip shield and stainless steel fixings withstand the rigors of an adverse environment: heat, humidity and salt air. Circuit boards are protected with an acrylic coating for maximum corrosion resistance. Temperature sensors ensure that power components will always operate within specified limits, if needed by automatic reduction of output current under extreme environmental conditions.   Universal 90-265V AC input voltage range and also suitable for DC supply (AC-DC and DC-DC operation) All models will operate without any adjustment needed over a 90 to 265 Volt input voltage range, whether 50 Hz or 60 Hz. The chargers also accept a 90-400 V DC supply.   Three outputs that each can supply the full output current Three isolated outputs to simultaneously charge 3 battery banks. Each output is capable to supply the full rated current.   Three-stage charging, with temperature compensation The Centaur charges at bulk rate until the output has reduced to 70% of the rated Amps, at which a 4 hour timer begins. After the timed period the charger switches to float rate. An internal temperature sensor is used to compensate the charge voltage with – 2 mV/ºC (– 1 mV/ºF) per cell. A DIP switch is available to select the optimum charge/float voltages for Flooded Lead-acid, Gel or AGM batteries. Brand Victron Energy Manufacturer Part Number CCH012060000 Voltage 12 Charger Amps 60 Outputs 3 Recommended Battery Capacity 240 – 600Ah Battery Connection M8 Studs IP Rating IP20 Dimensions H426 x W239 x H135mm Weight (kg) 5 Warranty 5 Years

Read more less

Features Quality without compromise Aluminium epoxy powder coated cases with drip shield and stainless steel fixings withstand the rigors of an adverse environment: heat, humidity and salt air. Circuit boards are protected with an acrylic coating for maximum corrosion resistance. Temperature sensors ensure that power components will always operate within specified limits, if needed by automatic reduction of output current under extreme environmental conditions.   Universal 90-265V AC input voltage range and also suitable for DC supply (AC-DC and DC-DC operation) All models will operate without any adjustment needed over a 90 to 265 Volt input voltage range, whether 50 Hz or 60 Hz. The chargers also accept a 90-400 V DC supply.   Three outputs that each can supply the full output current Three isolated outputs to simultaneously charge 3 battery banks. Each output is capable to supply the full rated current.   Three-stage charging, with temperature compensation The Centaur charges at bulk rate until the output has reduced to 70% of the rated Amps, at which a 4 hour timer begins. After the timed period the charger switches to float rate. An internal temperature sensor is used to compensate the charge voltage with – 2 mV/ºC (– 1 mV/ºF) per cell. A DIP switch is available to select the optimum charge/float voltages for Flooded Lead-acid, Gel or AGM batteries. Brand Victron Energy Manufacturer Part Number CCH024040000 Voltage 24 Charger Amps 40 Outputs 3 Recommended Battery Capacity 160 – 400Ah Battery Connection M8 Studs IP Rating IP20 Dimensions H505 x W255 x x H130mm Weight (kg) 12 Warranty 5 Years

Read more less

The IP65 rating makes this charger especially suitable for marine, mobile, and industrial applications and it can withstand the rigors of an adverse environment: heat, humidity and salt air. Features Skylla-IP65 (1+1): two outputs to charge 2 battery banks The Skylla-IP65 (1+1) features 2 isolated outputs. The second output, limited to approximately 3 A and with a slightly lower output voltage, is intended to top up a starter battery IP65 protection Steel epoxy powder coated case. Withstands the rigors of an adverse environment: heat, humidity and salt air. Circuit boards are protected with an acrylic coating for maximum corrosion resistance. Temperature sensors ensure that power components will always operate within specified limits, if needed by automatic reduction of output current under extreme environmental conditions. LCD display For status monitoring and to easily adapt the charge algorithm to a particular battery and its conditions of use. CAN-bus interface (NMEA2000) To connect to a CAN-bus network, to a Skylla-i Control panel or to the Color Control digital display. Synchronised parallel operation Several chargers can be connected in parallel and synchronised with help of the CAN-bus interface. This is achieved by simply interconnecting the chargers with RJ45 UTP-cables. The right amount of charge for a lead-acid battery: variable absorption time When only shallow discharges occur the absorption time is kept short in order to prevent overcharging of the battery. After a deep discharge the absorption time is automatically increased to make sure that the battery is completely recharged. Preventing damage due to excessive gassing: the BatterySafe mode If, in order to quickly charge a battery, a high charge current in combination with a high absorption voltage has been chosen, the Skylla-IP65 will prevent damage due to excessive gassing by automatically limiting the rate of voltage increase once the gassing voltage has been reached. Less maintenance and aging when the battery is not in use: the Storage mode The Storage mode kicks in whenever the battery has not been subjected to discharge during 24 hours. In the storage mode float voltage is reduced to 2,2 V/cell (26,4 V for 24 V battery) to minimise gassing and corrosion of the positive plates. Once a week the voltage is raised back to the absorption level to ‘refresh’ the battery. This feature prevents stratification of the electrolyte and sulphation, a major cause of early battery failure. To increase battery life: temperature compensation Every Skylla-IP65 comes with a battery temperature sensor. When connected, charge voltage will automatically decrease with increasing battery temperature. This feature is especially recommended for sealed lead-acid batteries and/or when important fluctuations of battery temperature are expected. Battery voltage sense In order to compensate for voltage loss due to cable resistance, the Skylla-IP65 is provided with a voltage sense facility so that the battery always receives the correct charge voltage. Use as a power supply As a result of the excellent control circuit, the Skylla-IP65 can be used as a power supply with perfectly stabilized output voltage if batteries or large buffer capacitors are not available. Li-Ion (LiFePO4) ready Simple charger on-off control can be implemented by connecting a relay or open collector opto coupler output from a Li-Ion BMS to the remote control port of the charger. Alternatively complete control of voltage and current can be achieved by connecting to the CAN-bus port. Brand Victron Energy Manufacturer Part Number SKY012070000 GTIN 8719076051961 Input Voltage 120/230V Input Voltage Range 90-265V Maximum AC input current @ 100 VAC 12A Charge current 70A Charge Algorithm 7 stage adaptive Battery Capacity 350-700Ah Temperature Sensor Yes Can Be Used As Power Supply Yes Remote on-off port Yes (can be connected to a Li-Ion BMS) Battery-Connection M6 bolts 230 VAC-connection Screw-clamp 6mm² (AWG 10) Protection Category IP65 Dimensions H401 x W265 x D151mm Weight 6Kg Warranty 5 Years

Read more less

The Energy Meter can be used to: Grid meter, and used as control input for an ESS System (1). Measure the output of a PV Inverter Measure the output of a AC Genset The meter is connected to the Color Control GX. There are two options in its wiring: Direct connection, either using the RS485 to USB interface with 1.8m cable length, or the 5.0m cable. Wireless connection via Zigbee Brand Victron Energy Manufacturer Part Number REL300300000 Warranty 5 Years

Read more less

Brand Victron Energy Manufacturer Part Number ASS300400200 Power USB Port 5V Dimensions H70 x W50 x D24mm Warranty 5 Years

Read more less

Brand Victron Energy Manufacturer Part Number CTR110000500 Weight (kg) 0.06 Warranty 5 Years

Read more less

To easily mount the MPPT Control on a wall, instead of flush mounted in a panel, use one of our wall mount enclosures. See the related products slider below.  Features  View live status information, including solar watts, battery voltage, charge current, load current and more.  View historical information    A. All-time values    B. 30-day historical values MPPT setup Brand Victron Energy Manufacturer Part Number SCC900500000 Power Supply Voltage Range 6.5-95 V DC Warranty 5 Years

Read more less

Brand Victron Energy Manufacturer Part Number SDRPCSV Frequency (Hz) 50/60 Dimensions L65 x W60 x D40mm Warranty 5 Years

Read more less

  Brand ASS030066003 Manufacturer Part Number ASS030066003 Cable Length 0.3m Warranty 5 Years

Read more less

  Brand Victron Energy Manufacturer Part Number ASS030066150 Cable Length 15m Warranty 5 Years

Read more less

Brand Victron Energy Manufacturer Part Number ASS030531209 Cable Length 0.9m Warranty 5 Years

Read more less

Brand Victron Energy Manufacturer Part Number ASS030531250 Cable Length 5m Warranty 5 Years

Read more less

The Argo Battery Isolators feature a low voltage drop thanks to the use of Schottky diodes: at low current the voltage drop is approximately 0,3 V and at the rated output approximately 0,45 V. All models are fitted with a compensation diode that can be used to slightly increase the output voltage of the alternator. This compensates for the voltage drop over the diodes in the isolator.   Please see Victron Energy’s ‘Energy Unlimited’ or ask for specialist advice when installing a diode isolator. Simply inserting the isolator in the cabling between the alternator and the batteries will slightly reduce charge voltage. The result can be that batteries are not charged to the full 100% and age prematurely.   Alternator energize input Some alternators need DC voltage on the B+ output to start charging. Obviously, DC will be present when the alternator is directly connected to a battery. Inserting a Diode or FET splitter will however prevent any return voltage/current from the batteries to the B+, and the alternator will not start. The new ‘AC’ diode isolators feature a special current limited energize input that will power the B+ when the engine run/stop switch is closed. Brand Victron Energy Manufacturer Part Number ARG120201020R Maximum Charge Current (A) 120 Maximum Alternator Current (A) 120 Number Of Batteries 2 Alternator Energize Input Yes Connection M8 Studs Compensation diode & Energize connection 6.3mm Faston Dimensions H60 x W120 x D115mm Weight (kg) 0.8 Warranty 5 Years

Read more less

The Argo Battery Isolators feature a low voltage drop thanks to the use of Schottky diodes: at low current the voltage drop is approximately 0,3 V and at the rated output approximately 0,45 V. All models are fitted with a compensation diode that can be used to slightly increase the output voltage of the alternator. This compensates for the voltage drop over the diodes in the isolator. Please see Victron Energy’s ‘Energy Unlimited’ or ask for specialist advice when installing a diode isolator. Simply inserting the isolator in the cabling between the alternator and the batteries will slightly reduce charge voltage. The result can be that batteries are not charged to the full 100% and age prematurely. Alternator energize input Some alternators need DC voltage on the B+ output to start charging. Obviously, DC will be present when the alternator is directly connected to a battery. Inserting a Diode or FET splitter will however prevent any return voltage/current from the batteries to the B+, and the alternator will not start. The new ‘AC’ diode isolators feature a special current limited energize input that will power the B+ when the engine run/stop switch is closed. Brand Victron Energy Manufacturer Part Number ARG140301020R GTIN 8719076019107 Maximum Charge Current 140A Maximum Alternator Current 140A Number of Batteries 3 Alternator Energize Input Yes Connection M8 Studs Compensation Diode & Energize Connection 6.3mm Faston Dimensions H60 x W120 x D150mm Weight 1.1Kg Warranty 5 Years    

Read more less

The Argo Battery Isolators feature a low voltage drop thanks to the use of Schottky diodes: at low current the voltage drop is approximately 0,3 V and at the rated output approximately 0,45 V. All models are fitted with a compensation diode that can be used to slightly increase the output voltage of the alternator. This compensates for the voltage drop over the diodes in the isolator.   Please see Victron Energy’s ‘Energy Unlimited’ or ask for specialist advice when installing a diode isolator. Simply inserting the isolator in the cabling between the alternator and the batteries will slightly reduce charge voltage. The result can be that batteries are not charged to the full 100% and age prematurely.   Alternator energize input Some alternators need DC voltage on the B+ output to start charging. Obviously, DC will be present when the alternator is directly connected to a battery. Inserting a Diode or FET splitter will however prevent any return voltage/current from the batteries to the B+, and the alternator will not start. The new ‘AC’ diode isolators feature a special current limited energize input that will power the B+ when the engine run/stop switch is closed. Brand Victron Energy Manufacturer Part Number ARG160201020 Maximum Charge Current (A) 160 Maximum Alternator Current (A) 160 Number Of Batteries 2 Alternator Energize Input Yes Connection M8 Studs Compression didode & Energize connection 6.3mm Faston Dimensions H60 x W120 x D150mm Weight (kg) 1.1 Warranty 5 Years  

Read more less

Benefits The battery is charged, smartly… to perfect condition The seven-step charging algorithm gets the best out of your battery. The charger gives the battery the power it needs, maintains its health, ensures better performance… and a longer life. Recovery of deeply-discharged ‘dead’ batteries Unlike other brands, the Blue Smart IP65 Charger will attempt to recharge a deeply-discharged battery by force-feeding it with a low current. Normal charging will then be resumed as soon as there is sufficient voltage across the battery terminals. Connect the battery with ease The charger comes with both crocodile clips and M8 eyelets – making it easy to connect to the battery. If you wish, you can leave it permanently connected. Check the status of your battery remotely The Blue Smart IP65 is equipped with built-in Bluetooth, so the status of the charger and the battery can be checked on a smartphone, tablet or laptop. All settings of the charger can be configured with the VictronConnect app.   Features Water, dust and chemical resistant Seven step smart charge algorithm Recovery of fully discharged ‘dead’ batteries Automatic power supply function Severe cold performance: down to -30°C Several other battery life enhancing features Low power mode to charge smaller batteries Li-ion battery mode Setup and configure, readout of voltage and current by Bluetooth Smart Brand Victron Energy Manufacturer Part Number BPC240831024R GTIN 8719076040699 Voltage 24V Charge Current 8A Input Voltage 230V Number of Outputs 1 Protection Category IP65 (splash and dust proof) Efficiency 95% Bluetooth Enabled Yes Plug Type UK Dimensions H60 x W105 x D190mm Weight 0.9Kg Warranty 5 Years

Read more less

Features Multifunctional, with intelligent power management The MultiPlus is a powerful true sine wave inverter, a sophisticated battery charger that features adaptive charge technology, and a high-speed AC transfer switch in a single compact enclosure. Next to these primary functions, the MultiPlus has several advanced features, as outlined below. Parallel operation and three phase capability Up to six Multis can operate in parallel to achieve higher power output. In addition to parallel connection, three units can be configured for three-phase output. PowerControl – Dealing with limited generator, shore side or grid power With the Multi Control Panel a maximum generator or shore current can be set. The MultiPlus will then take account of other AC loads and use whatever is extra for charging, thus preventing the generator or shore supply from being overloaded. PowerAssist – Boosting the capacity of shore or generator power This feature takes the principle of PowerControl to a further dimension. It allows the MultiPlus to supplement the capacity of the alternative source. Where peak power is so often required only for a limited period, the MultiPlus will make sure that insufficient shore or generator power is immediately compensated for by power from the battery. When the load reduces, the spare power is used to recharge the battery. Four stage adaptive charger and dual bank battery charging The main output provides a powerful charge to the battery system by means of advanced ‘adaptive charge’ software. The software fine-tunes the three-stage automatic process to suit the condition of the battery, and adds a fourth stage for long periods of float charging. The adaptive charge process is described in more detail on the Phoenix Charger datasheet and on our website, under Technical Information. In addition to this, the MultiPlus will charge a second battery using an independent trickle charge output intended for a main engine or generator starter battery. High start-up power Needed to start high inrush loads such as power converters for LED lamps, halogen lamps or electric tools. Search Mode When Search Mode is ‘on’, the power consumption of the inverter in no-load operation is decreased by approx. 70%. In this mode the Multi, when operating in inverter mode, is switched off in case of no load or very low load, and switches on every two seconds for a short period. If the output current exceeds a set level, the inverter will continue to operate. If not, the inverter will shut down again. Programmable relay By default, the programmable relay is set as an alarm relay, i.e. the relay will de-energise in the event of an alarm or a pre-alarm (inverter almost too hot, ripple on the input almost too high, battery voltage almost too low). Remote on / off / charger on Three pole connector. On-site system configuring, monitoring and control After installation, the MultiPlus is ready to go. Some settings can be changed with DIP switches. 500/800/1200VA models: remote switch / battery charge voltage / inverter frequency /search mode. 1600/2000VA models: battery charge voltage /search mode. For more settings use VE-Config or the VE.Bus Smart dongle. Remote configuring and monitoring Install a Cerbo GX or other GX product to connect to the internet. Operational data can be stored and displayed on our VRM (Victron Remote Management) website, free of charge. When connected to the internet, systems can be accessed remotely, and settings can be changed. Brand Victron Energy Manufacturer Part Number PMP482200000 GTIN 8719076049470 Voltage 48V Cont. output power at 25ºC 2000VA Peak Power 3500W Output AC Voltage 230V Transfer Switch 35A Charge Current House Battery 25A Protection Category IP22 Efficiency 95% Bluetooth Compatible No Dimensions H506 x W236 x D147mm Weight 15.5Kg Warranty 5 Years

Read more less

Please contact us for more information.

Read more less

 Currently we do not have a solution in stock to attach this to Fastensol rails.

Read more less

Part No: FE-T-17.0 Inverters - Main Units Rating: 17,000W Phases: 3 FOX ESS - PV Inverter - T Series - 17.0kW T17-G3 Don't forget: You must register your install with Fox online to activate the 10 year product warranty, otherwise it's 5 years as standard. Supplier Part No: T17 Weight: 20 kg Rated Power: 17,000 W Min PPT Voltage: 140 V Max PPT Voltage: 1,100 V DC Startup Voltage: 140 V DC Shutdown Voltage: 1,100 V Max Input Voltage: 1,100 V Max DC Power: 25,500 W Max AC Power (5 Minutes): 17,000 W Surge AC Power (1 Second): 18,700 W Max DC Current: 28 A Max DC Inputs: 4 Has DC Fuses: 4 Connector: MC4   Included Connectors: 4 Euro Efficiency: 97.8 % Transformer: N/A MPPT Quantity : 2 Has Integrated DC Switch:Yes Warranty: 5 years

Read more less

Part No: FE-T-6.0 Inverters - Main Units Rating: 6,000W Phases: 3 FOX ESS - PV Inverter - T Series - 6.0kW T6-G3 Don't forget: You must register your install with Fox online to activate the 10 year product warranty, otherwise it's 5 years as standard. Supplier Part No: T6 Weight: 17 kg Rated Power: 6,000 W Min PPT Voltage: 140 V Max PPT Voltage: 1,100 V DC Startup Voltage: 140 V DC Shutdown Voltage: 1,100 V Max Input Voltage: 1,100 V Max DC Power: 9,000 W Max AC Power (5 Minutes): 6,000 W Surge AC Power (1 Second): 6,600 W Max DC Current: 14 A Max DC Inputs: 2 Has DC Fuses: 2 Connector: MC4   Included Connectors: 2 Euro Efficiency: 97.8 % Transformer: N/A MPPT Quantity : 2 Has Integrated DC Switch: Yes Warranty: 5 years

Read more less

Part No: FE-F6000 Inverters - Main Units Rating: 6,000W Phases: 1 FOX ESS - PV Inverter - F Series - 6kW F6000 Our Dual-MPPT F Series range includes 3.0 - 6.0kW models. The F Series is IP65 rated and battery ready for easy upgrade when paired with a Fox ESS charge controller. High Performance: Low start-up voltage, wide voltage range, 97.4% maximum efficiency. Easy Installation: Flexible configuration, plug and play set-up. IP65 Rated: Engineered to last with maximum flexibility. Suitable for outdoor installation. Remote Monitoring: Monitor your system remotely via smartphone app or web portal. Don't forget: You must register your install with Fox online to activate the 10 year product warranty, otherwise it's 5 years as standard. Supplier Part No: F6000 Weight: 15.5 kg Rated Power: 6,000 W Min PPT Voltage: 120 V Max PPT Voltage: 600 V DC Startup Voltage: 120 V DC Shutdown Voltage: 601 V Max Input Voltage: 600 V Max DC Power: 9,000 W Max AC Power (5 Minutes): 6,000 W Surge AC Power (1 Second): 0 W Max DC Current: 25 A Max DC Inputs: 2 Has DC Fuses: 0 Connector: MC4   Included Connectors: 0 Euro Efficiency: 96.8 % Transformer: HF MPPT Quantity : 2 Has Integrated DC Switch: Yes Warranty: 5 years

Read more less

Part No: FE-S1000 Inverters - Main Units Rating: 1,000W Phases: 1 FOX ESS - PV Inverter - S Series - 1.0kW S1000-G2 Don't forget: You must register your install with Fox online to activate the 10 year product warranty, otherwise it's 5 years as standard. Supplier Part No: S1000 Weight: 5.4 kg Rated Power: 1,000 W Min PPT Voltage: 60 V Max PPT Voltage: 500 V DC Startup Voltage: 60 V DC Shutdown Voltage: 500 V Max Input Voltage: 500 V Max DC Power: 1,500 W Max AC Power (5 Minutes): 1,000 W Surge AC Power (1 Second): 1,100 W Max DC Current: 14 A Max DC Inputs: 1 Has DC Fuses: 1 Connector: MC4   Included Connectors: 1 Euro Efficiency: 96.5 % Transformer: N/A MPPT Quantity : 1 Has Integrated DC Switch: Yes Warranty: 5 years

Read more less

Pre built and pre programmed by our Tech Team, this board will help you get Off Grid in no time at all.All you need to do it put it up where you want it, plug in your batteries and solar panels and you’re ready to go Off Grid. Let us know what your goal is and we can tell you how best to achieve it. Drop us a message at: info@powerland.co.uk * The boards are built to order. Please allow 2-6 weeks for them to be completed prior to dispatch. We will contact you to confirm lead time once the order has been placed *Image for display purposes only Kit includes: Victron Energy MultiPlus-II 48/5000/70-50 230V – PMP482505010 – this is the “muscle” of your system that changes the DC from the batteries to AC to power your home. Victron Energy Lynx Distributor – LYN060102000 – this is a combined fuse holder and power distribution for your system Victron Energy SmartSolar MPPT 150/45 – SCC115045212 – this takes the electricity that your panels generate and regulates it to your batteries. Victron Energy Cerbo GX – BPP900450100 – this is the “brain” of your system ensuring that all components talk to each other Victron Energy GX Touch 50 – BPP900455050 – a sleek touch screen that gives you a pictorial overview of your system Victron Energy GX Touch 50 Wall Mount – BPP900465050 IMO Enclosed DC Switch 2P 25A – SI25-PEL64R-2 – ensures a safe way to isolate your solar panels if you ever need to. Blue Sea e-Series On-Off Battery Switch – 9004E-BSS Consumer Unit – provides protection for the 230VAC output from the Multiplus. Victron Energy MEGA-fuse 200A/58V for 48V products (CIP137200010) and MEGA-fuse 125A/58V for 48V products (CIP137125010) – hidden away in the Lynx Distributor these protect the Multiplus and wiring. Victron Energy VE.Direct Cable 3m – ASS030530230 – provides data communication between your solar controller and GX devices Victron Energy RJ45 UTP Cable 3m – ASS030064980 – provides data communication between your multiplus and GX device All additional cabling, lugs and trunking to make the set up just right. * * Please note the names of the kits are for reference only, not all households are the same. Please feel free to get in touch to confirm which kit is perfect for you. * *  

Read more less

This kit is adaptable to your current set up or can be added to to help you achieve the perfect Off Grid set up. By not including an MPPT you can customize this kit to your needs using the handy Victron MPPT sizing calculator: https://www.victronenergy.com/mppt-calculator Alternatively, let us know what your goal is and we can tell you how best to achieve it. Drop us a message at: info@powerland.co.uk * The boards are built to order. Please allow 2-6 weeks for them to be completed prior to dispatch. We will contact you to confirm lead time once the order has been placed *Image for display purposes only Kit includes: Victron Energy MultiPlus-II 48/5000/70-50 230V – PMP482505010 Victron Energy Lynx Distributor – LYN060102000 Victron Energy Cerbo GX – BPP900450100 Victron Energy GX Touch 50 – BPP900455050  Victron Energy GX Touch 50 Wall Mount – BPP900465050 IMO Enclosed DC Switch 2P 25A – SI25-PEL64R-2 Blue Sea e-Series On-Off Battery Switch – 9004E-BSS Consumer Unit Victron Energy MEGA-fuse 200A/58V for 48V products (1 pc) – CIP137200010 Victron Energy MEGA-fuse 125A/58V for 48V products (1 pc) – CIP137125010 Victron Energy VE.Direct Cable 3m – ASS030530230 Victron Energy RJ45 UTP Cable 3m – ASS030064980 All additional cabling, lugs and trunking to make the set up just right

Read more less

Pre built and pre programmed by our Tech Team, this board will help you get your ESS set up working in no time at all.All you need to do it put it up where you want it, plug in your batteries and solar panels and you’re ready to go Off Grid. Let us know what your goal is and we can tell you how best to achieve it. Drop us a message at: info@powerland.co.uk * The boards are built to order. Please allow 2-6 weeks for them to be completed prior to dispatch. We will contact you to confirm lead time once the order has been placed *Image for display purposes only Kit includes: Victron Energy MultiPlus-II 48/10000/140-100 230V – PMP483105000 Victron Energy Lynx Distributor – LYN060102000 Victron Energy SmartSolar MPPT 150/45 – SCC115045212 Victron Energy Cerbo GX – BPP900450100 Victron Energy GX Touch 50 – BPP900455050  Victron Energy GX Touch 50 Wall Mount – BPP900465050 IMO Enclosed DC Switch 2P 25A – SI25-PEL64R-2 Consumer Unit Victron Energy MEGA-fuse 200A/58V for 48V products (1 pc) – CIP137200010 Victron Energy MEGA-fuse 125A/58V for 48V products (1 pc) – CIP137125010 Victron Energy VE.Direct Cable 3m – ASS030530230 Victron Energy RJ45 UTP Cable 3m – ASS030064980 All additional cabling, lugs and trunking to make the set up just right.

Read more less

Pre built and pre programmed by our Tech Team, this board will help you get your ESS set up working in no time at all.All you need to do it put it up where you want it, plug in your batteries and solar panels and you’re ready to go Off Grid. Let us know what your goal is and we can tell you how best to achieve it. Drop us a message at: info@powerland.co.uk * The boards are built to order. Please allow 2-6 weeks for them to be completed prior to dispatch. We will contact you to confirm lead time once the order has been placed* *Image for display purposes only* Kit includes: Victron Energy MultiPlus-II 48/3000/35-32 230V – PMP482305012 Victron Energy Lynx Distributor – LYN060102000 Victron Energy SmartSolar MPPT 150/45 – SCC115045212 Victron Energy Cerbo GX – BPP900450100 Victron Energy GX Touch 50 – BPP900455050  Victron Energy GX Touch 50 Wall Mount – BPP900465050 IMO Enclosed DC Switch 2P 25A – SI25-PEL64R-2 Consumer Unit Victron Energy MEGA-fuse 125A/58V for 48V products (1 pc) – CIP137125010 Victron Energy VE.Direct Cable 3m – ASS030530230 Victron Energy RJ45 UTP Cable 3m – ASS030064980 All additional cabling, lugs and trunking to make the set up just right.

Read more less

CODE R-B12300A MPN (MANUFACTURER PART NUMBER) R-B12300A BRAND Topband Topband battery makes our products available through the best knowledge-based distribution and service organizations for the people and businesses who rely on batteries to work, live, or get away. Topband battery provides advanced LiFePO4 batteries for lead acid drop-in battery solution, light and compact drop-in replacement Features Standard lead acid cases, customized case Bluetooth app monitoring Heating function optional 4000+cycles，80%DOD UN38.3/CE certified Support series or parallel connection Nominal Voltage 12.8V Battery Capacity 300Ah Terminal Type M8 Dimensions L520 x W269x H220mm Weight 37.7Kg Warranty 5 Years Battery Technology Lithium Battery Application Deep Cycle Max. Charge Current 200Ah

Read more less

CODE R-B12200A MPN (MANUFACTURER PART NUMBER) R-B12200A BRAND Topband Topband battery makes our products available through the best knowledge-based distribution and service organizations for the people and businesses who rely on batteries to work, live, or get away. Topband battery provides advanced LiFePO4 batteries for lead acid drop-in battery solution, light and compact drop-in replacement Features Standard lead acid cases, customized case Bluetooth app monitoring Heating function optional 4000+cycles，80%DOD UN38.3/CE certified Support series or parallel connection Nominal Voltage 12.8V Battery Capacity 200Ah Terminal Type M8 Dimensions L484 x W170 x H241mm Weight 25Kg Warranty 5 Years Battery Technology Lithium Battery Application Deep Cycle Max. Charge Current 200A

Read more less

Part No: MYEN-PEDESTAL EV Charging - Mounting   Supplier Part No: Zappi Pedestal Weight: 10 kg

Read more less

CODE LVS CONNECTOR 70mm2 MPN (MANUFACTURER PART NUMBER) LVS CONNECTOR 70mm2 BRAND BYD Weight 0.2

Read more less

CODE LVS CONNECTOR 50mm2 MPN (MANUFACTURER PART NUMBER) LVS CONNECTOR 50mm2 BRAND BYD Weight 0.2

Read more less

CODE LVS CONNECTOR 35mm2 MPN (MANUFACTURER PART NUMBER) LVS CONNECTOR 35mm2 BRAND BYD Weight 0.2

Read more less

CODE HVM13.8 MPN (MANUFACTURER PART NUMBER) HVM13.8 BRAND BYD Battery-Box Premium HVM One Battery-Box Premium HVM is composed of 3 to 8 B-Plus HVM 2.71 battery modules that are serially connected to achieve a usable capacity of 8.1 to 21.7 kWh. Additionally, direct parallel connection of up to 3 identical Battery-Box Premium HVM allows a maximum capacity of 65.0 kWh. Ability to scale by adding HVM modules or parallel HVM stacks at anytime.

Read more less

CODE TN-LFP12.8V60AH MPN (MANUFACTURER PART NUMBER) TN60 Features Using the technology of lithium iron phosphate cell, superior safety, thousands of cycles, 100%DOD, under normal conditions Built-in automatic protection for over-charge, over discharge, over current and over temperature Free of maintenance Internal cell balancing Lighter weight: About 40% -50% of the weight of a comparable lead acid battery Can be charged using most standard lead-acid charges (set) Wider temperature range:-20°C-60°C Support for Series application expansion (up to 51.2V) and two in parallel Applications UPS Solar &Wind Power System Golf Cart Electric Vehicle , E-bike, E-rickshaw etc. Lighting   Voltage 12V Battery Capacity (C20) 60Ah Terminal Type M6 Terminal Layout Left Hand Positive Dimensions (Including Terminals) L229 x W138 x H217mm Weight 7.2Kg Country of Manufacture China Battery Technology Lithium Battery Application Deep Cycle

Read more less

Part No: EN-EFM-35MM Inverters - Micro Inverter Mounting Makes Enphase Microinverters Compatible with Railless and Ballasted Systems   Bolts microinverters directly to the module frame, eliminating design challenges with both residential and commercial systems Comes in two sizes that fit the majority of modules    Faster Installations   Bolt microinverters to module frames on the ground, then carry the complete module up to the roof for rapid, drop-in installation Simple, two-piece bracket attaches in three easy steps   More Affordable   Installing with the Enphase Frame Mount requires fewer parts than other frame mount solutions, saving you material costs Reduce labour costs with faster, more efficient installations   Reliable   The Enphase Frame Mount is made of anodized aluminium for a strong, rust-free bracket Engineered specifically for use with Enphase Microinverters   Supplier Part No:EFM-35MM Weight:0.115 kg

Read more less

The Full Throttle TPPL High Cranking Batteries are purpose-built to meet the ever-increasing demands of today's vehicles. With pure-lead cells and thin-plate technology, Full Throttle Batteries ensure a consistent and dependable power supply, even under the most demanding conditions.Full Throttle Batteries are incredibly versatile, catering to a wide range of vehicle applications, including cars, trucks, motorcycles, marine vessels, power sports vehicles, and emergency service vehicles. With their reputation for endurance, reliability, and longevity, Full Throttle batteries are built to withstand the test of time and the rigors of any environment Brand Fullriver Product Code FT610-47 Voltage 12 Volts Technology AGM Capacity (C20) 50 Ah MCA 745 A CCA (EN) 610 A PHCA (5 sec) 1280 A Length 241 mm Width 175 mm Height inc. terms 190 mm Guarantee 2 Years   Warranty 5 Years 

Read more less

S6-275AGM Rolls 6V AGM-S Series Battery Based in Nova Scotia, Canada. Since 1959, the company has produced a wide range of Rolls-branded premium deep cycle batteries for use in Renewable Energy, Marine, Motive Power and Railroad applications. Rolls flooded and sealed AGM & GEL VRLA products are internationally recognised for their dependability, cycle life and outstanding quality. The Rolls AGM-S Series Rolls high quality AGM-S VRLA batteries offer true deep cycle performance, increased capacity and extended cycle life in a rugged, sealed, shock and vibration-resistant ABS case design for added durability, ideal for a variety of remote and confined off-grid, grid-tied and backup applications. AGM-S FEATURES • Sealed construction • New high-density active paste • Heavy duty thick plates • ABS case and cover • Superior corrosion resistance • Maintenance free, spill-proof/leak-proof • Self regulating pressure release valves • Low self discharge rate, only 3%/month • Faster recharging time   All Prices Include VAT   Brand Rolls Voltage 6 Volts Technology AGM Capacity (C20) 250 Ah Weight 35 Kg Length 262 mm Width 181 mm Height inc. terms 273 mm Guarantee 1 Year    

Read more less

R12-260AGM Rolls 12V AGM-R Series Battery Based in Nova Scotia, Canada. Since 1959, the company has produced a wide range of Rolls-branded premium deep cycle batteries for use in Renewable Energy, Marine, Motive Power and Railroad applications. Rolls flooded and sealed AGM & GEL VRLA products are internationally recognised for their dependability, cycle life and outstanding quality. The Rolls AGM-R Series This range of dual purpose sealed maintenance-free 12-volt AGM-R batteries offering outstanding value and performance. The AGM-R line offers a lower self-discharge and an increased acceptance to charge current than conventional flooded wet batteries, allowing faster recharge. Incorporating all of the leading design features associated with Absorbed Glass Mat technology, the AGM-R line provides the perfect solution when looking to replace wet batteries or upgrade existing sealed batteries. AGM-R FEATURES • Maintenance-free sealed construction • Low internal resistance allowing faster recharge • Shock and vibration-resistance ABS case • 850 cycles at 50% DOD* • Standard dimensions for easy retro-fit   All Prices Include VAT Brand Rolls Voltage 12 Volts Technology AGM Capacity (C20) 260 Ah Weight 73 Kg Length 522 mm Width 268 mm Height inc. terms 240 mm Guarantee 1 Year    

Read more less