Quick Order
Victron Victron Energy Temperature sensor type C – ASS000020000
Brand Victron Energy Manufacturer Part Number ASS000020000 GTIN 8719076048039 Products Supported Inverter RS Smart Solar Temperature on VRM No VE.Smart Networking No Warranty 5 Years
£14.00 Exc. VAT
£16.80 Inc. VAT
In stock
Victron Victron Energy VE.Net GMDSS Panel – VPN000200000
Brand Victron Energy Manufacturer Part Number VPN000200000 Dimensions L65 x W120 x H40mm Weight (kg) 0.1 Warranty 5 Years
£137.47 Exc. VAT
£164.96 Inc. VAT
In stock
Victron Victron Energy VE.Can resistive tank sender adapter – BPP900600100
When you use a Skylla-i or a MPPT with CAN bus in the system, the power to the CAN bus will be supplied by either one of them. When the CAN bus is not powered by a Skylla-I or a MPPT, you will need the new VE.Can Power Cable to supply the power. Brand Victron Energy Manufacturer Part Number BPP900600100 Warranty 5 Years
£244.98 Exc. VAT
£293.98 Inc. VAT
In stock
Victron Victron Energy GX GSM 850/1900 – GSM100200100
It includes a built-in GPS receiver. When the optional GPS antenna is installed, the system can be tracked as well as Geo-fenced on the VRM Portal. Note that many telecom operators are in the process of shutting down their 3G networks. Make sure to consider the replacement product, the GX LTE 4G, as well. Brand Victron Energy Manufacturer Part Number GSM100200100 GTIN 8719076051534 Input Voltage Range 8-70VDC Antenna Connector Type SMA Female Dimensions L106 × W42.5 × H22mm Warranty 5 Years
£152.68 Exc. VAT
£183.22 Inc. VAT
In stock
Victron Victron Energy Outdoor 2G and 3G GSM Antenna – GSM900100100
Brand Victron Energy Manufacturer Part Number GSM900100100 Warranty 5 Years
£27.13 Exc. VAT
£32.56 Inc. VAT
In stock
Victron Victron Energy Outdoor 4G GSM Antenna – GSM900100400
Brand Victron Energy Manufacturer Part Number GSM900100400 GTIN 8719076052951 Weight 0.01Kg Warranty 5 Years
£20.30 Exc. VAT
£24.36 Inc. VAT
In stock
Victron Victron Energy GlobalLink 520 – ASS030543020
Features Global connectivity with 4G LTE-M LTE-M is the abbreviation for LTE Cat-M1 or Long Term Evolution (4G), category M1. This cellular technology is designed to connect Internet of Things devices to existing 4G towers while using low energy. LTE-M does support handovers and roaming so it is possible to use this device in a moving vehicle like a campervan. Check https://1nce.com/en/coverage/ to see if LTE-M is officially confirmed to be available in your area. Coverage is increasing every week as local providers roll out support. Your purchase includes 5 years of connectivity, so there is no need to worry about purchasing a separate data bundle and SIM-card. Easy system monitoring & control Your GlobalLink 520 comes with two VE.Direct ports which allows you to connect up to two VE.Direct devices such as a BMV Battery Monitor and/or a MPPT Solar Charge Controller directly to VRM. With two digital inputs that also act as pulse counters and a remote controllable relay, it’s a perfect solution to monitor and control your installation. Antenna built in The GlobalLink 520 comes with a built-in antenna that is designed to work all around the globe. However if you require better reception or want to install your module in a utility van for example, it is also possible to mount an external antenna. Victron Remote Management The online Victron Remote Management (VRM) portal provides you with access to your installation, from anywhere, at any time. In VRM you can check the status of your connected products, view detailed history graphs of your energy, generate detailed analytical reports, and even configure automatic alarms in case something goes wrong. Brand Victron Energy Manufacturer Part Number ASS030543020 GTIN 8719076053644 Warranty 5 Years
£136.66 Exc. VAT
£163.99 Inc. VAT
In stock
Victron Victron Energy Anti-islanding relay UFR1001E – REL100100000
Brand Victron Energy Manufacturer Part Number REL100100000 Dimensions H90 x W105 x D69mm Weight (kg) 0.25 Warranty 5 Years
£520.00 Exc. VAT
£624.00 Inc. VAT
In stock
Victron Victron Energy Battery Alarm GX – BPA000100010R
Brand Victron Energy Manufacturer Part Number BPA000100010R Dimensions L120 x W65 x D3mm Weight (kg) 0.2 Warranty 5 Years
£43.00 Exc. VAT
£51.60 Inc. VAT
In stock
Victron Victron Energy Phoenix Inverter Control – REC030001210
Brand Victron Energy Manufacturer Part Number REC030001210 Warranty 5 Years
£55.67 Exc. VAT
£66.80 Inc. VAT
In stock
Victron Victron Energy Phoenix Charger Control – REC0100011100
Brand Victron Energy Manufacturer Part Number REC010001110 Dimensions L120 x W65 x D4mm Weight (kg) 0.1 Warranty 5 Years
£70.00 Exc. VAT
£84.00 Inc. VAT
In stock
Victron Victron Energy Wall mount enclosure for 65 x 120 mm GX-panels – ASS050300010
Brand Victron Energy Manufacturer Part Number ASS050300010 Dimensions H88 x W130 x D40mm Warranty 5 Years
£18.43 Exc. VAT
£22.12 Inc. VAT
In stock
Victron Victron Energy Wall Mount Enclosure for BMV or MPPT Control – ASS050500000
Brand Victron Energy Manufacturer Part Number ASS050500000 Dimensions H88 x W130 x D47mm Warranty 5 Years
£16.89 Exc. VAT
£20.27 Inc. VAT
In stock
Victron Victron Energy Wall mounted enclosure for Color Control GX and BMV or MPPT – ASS050600000
Brand Victron Energy Manufacturer Part Number ASS050600000 Dimensions H244 x W135 x D75mm Warranty 5 Years
£26.11 Exc. VAT
£31.33 Inc. VAT
In stock
Victron Victron Energy USB extension cable 0.3m one side right angle – ASS060000100
Brand Victron Energy Manufacturer Part Number ASS060000100 Cable Length 0.3m Warranty 5 Years
£5.38 Exc. VAT
£6.46 Inc. VAT
In stock
Victron Victron Energy RJ12 UTP Cable 0.3m – ASS030066003
Brand ASS030066003 Manufacturer Part Number ASS030066003 Cable Length 0.3m Warranty 5 Years
£6.14 Exc. VAT
£7.37 Inc. VAT
In stock
Victron Victron Energy RJ12 UTP Cable 0.9m – ASS030066009
Brand Victron Energy Manufacturer Part Number ASS030066009 Cable Length 0.9m Warranty 5 Years
£6.14 Exc. VAT
£7.37 Inc. VAT
In stock
Victron Victron Energy RJ12 UTP Cable 1.8m – ASS030066018
Brand Victron Energy Manufacturer Part Number ASS030066018 Cable Length 1.8m Warranty 5 Years
£6.14 Exc. VAT
£7.37 Inc. VAT
In stock
Victron Victron Energy RJ12 UTP Cable 3m – ASS030066030
Brand Victron Energy Manufacturer Part Number ASS030066030 Cable Length 3m Warranty 5 Years
£7.68 Exc. VAT
£9.22 Inc. VAT
In stock
Victron Victron Energy RJ12 UTP Cable 10m – ASS030066100
Brand Victron Energy Manufacturer Part Number ASS030066100 Cable Length 10m Warranty 5 Years
£19.19 Exc. VAT
£23.03 Inc. VAT
In stock
Victron Victron Energy RJ45 UTP Cable 0.3m – ASS030064900
Brand Victron Energy Manufacturer Part Number ASS030064900 Cable Length 0.3m Warranty 5 Years
£6.14 Exc. VAT
£7.37 Inc. VAT
In stock
Victron Victron Energy RJ45 UTP Cable 15m – ASS030065020
Brand Victron Energy Manufacturer Part Number ASS030065020 Cable Length 15m Warranty 5 Years
£19.19 Exc. VAT
£23.03 Inc. VAT
In stock
Victron Victron Energy RJ45 UTP Cable 20m – ASS030065030
Brand Victron Energy Manufacturer Part Number ASS030065030 Cable Length 20m Warranty 5 Years
£23.04 Exc. VAT
£27.65 Inc. VAT
In stock
Victron Victron Energy VE.Direct Cable 0.3m (one side Right Angle) – ASS030531203
Brand Victron Energy Manufacturer Part Number ASS030531203 Cable Length 0.3m Warranty 5 Years
£9.98 Exc. VAT
£11.98 Inc. VAT
In stock
Victron Victron Energy VE.Direct Cable 10m (one side Right Angle) – ASS030531320
Brand Victron Energy Manufacturer Part Number ASS030531320 Cable Length 10m Warranty 5 Years
£14.60 Exc. VAT
£17.52 Inc. VAT
In stock
Victron Victron Energy VE.Direct to BMV60xS Cable 1.5m – ASS030532215
Brand Victron Energy Manufacturer Part Number ASS030532215 GTIN 8719076019763 Cable Length 1.5m Warranty 5 Years
£25.45 Exc. VAT
£30.54 Inc. VAT
In stock
Victron Victron Energy VE.Direct to BMV60xS Cable 3m – ASS030532230
Brand Victron Energy Manufacturer Part Number ASS030532230 GTIN 8719076019763 Cable Length 3m Warranty 5 Years
£17.50 Exc. VAT
£21.00 Inc. VAT
In stock
Victron Victron Energy Interface MK2-USB (for Phoenix Charger only) – ASS030130010
Brand Victron Energy Manufacturer Part Number ASS030130010 GTIN 8719076019428 Weight 0.06Kg Warranty 5 Years
£57.60 Exc. VAT
£69.12 Inc. VAT
In stock
Victron Victron Energy CANUSB Interface – ASS030532010
Brand Victron Energy Manufacturer Part Number ASS030532010 Warranty 5 Years
£378.58 Exc. VAT
£454.30 Inc. VAT
In stock
Victron Victron Energy VE.Bus to NMEA2000 interface –
Brand Victron Energy Manufacturer Part Number ASS030520110 Warranty 5 Years
£168.35 Exc. VAT
£202.02 Inc. VAT
In stock
Victron Victron Energy VE.Direct to NMEA2000 interface – ASS030520310
Limitations: The cable does not work with other VE.Direct products, such as Solar Chargers, Inverters and also not with the BMV-712 Smart. When used in combination with a BMV-702 there is limited functionality with regards to the AUX function in the BMV: When used to measure starter battery voltage, that voltage will be transmitted to the NMEA2000 network. But when used to measure temperature and or mid-voltage, that data will not be transmitted on the NMEA2000 network. Brand Victron Energy Manufacturer Part Number ASS030520310 Warranty 5 Years
£168.35 Exc. VAT
£202.02 Inc. VAT
In stock
Victron Victron Energy Interface MK2.2b (VE.Bus to RS232) – ASS030120210
Brand Victron Energy Manufacturer Part Number ASS030120210 GTIN 8719076019404 Warranty 5 Years
£39.93 Exc. VAT
£47.92 Inc. VAT
In stock
Victron Victron Energy RS232 to USB Converter – ASS030200000
Brand Victron Energy Manufacturer Part Number ASS030200000 Warranty 5 Years
£21.50 Exc. VAT
£25.80 Inc. VAT
In stock
Victron Victron Energy VE.Direct to RS232 interface – ASS030520500
Brand Victron Energy Manufacturer Part Number ASS030520500 Warranty 5 Years
£19.97 Exc. VAT
£23.96 Inc. VAT
In stock
Victron Victron Energy VE.Direct to VE.Can interface – ASS030520410
Limitations: The interface cable does not work with other VE.Direct products, such as Solar Chargers, Inverters and also not with the BMV-712 Smart. When used in combination with a BMV-702 there is limited functionality with regards to the AUX function in the BMV: When used to measure starter battery voltage, that voltage will be transmitted to VE.Can. But when used to measure temperature and or mid-voltage, that data will not be transmitted on the VE.Can network. Brand Victron Energy Manufacturer Part Number ASS030520410 Warranty 5 Years
£270.58 Exc. VAT
£324.70 Inc. VAT
In stock
Victron Victron Energy VE.Can Power Cable – ASS030690000
Brand Victron Energy Manufacturer Part Number ASS030690000 Warranty 5 Years
£23.04 Exc. VAT
£27.65 Inc. VAT
In stock
Victron Victron Energy VE.Can RJ45 terminator (2 pack) – ASS030700000
Brand Victron Energy Manufacturer Part Number ASS030700000 Warranty 5 Years
£6.90 Exc. VAT
£8.28 Inc. VAT
2 in stock
Victron Victron Energy Orion 110/24-15A (360W) Isolated DC-DC Converter – ORI110243610
Remote on-off connector on the high power models The remote on-off eliminates the need for a high current switch in the input wiring. The remote on-off can be operated with a low power switch or by the engine run/stop switch. All models with adjustable output can also be used as a battery charger For example to charge a 12 Volt starter or accessory battery in an otherwise 24 Volt system. All models with adjustable output can be paralleled to increase output current Up to five units can be connected in parallel. Brand Victron Energy Manufacturer Part Number ORI110243610 Input Voltage Range 60-140V Output Voltage 24V Galvanic Isolation No Dimensions H82 x W132 x D190mm Weight (kg) 1.4 Warranty 5 Years
£230.00 Exc. VAT
£276.00 Inc. VAT
In stock
Victron Victron Energy Argodiode 80-2AC Two Batteries 80A – ARG080201000R
The Argo Battery Isolators feature a low voltage drop thanks to the use of Schottky diodes: at low current the voltage drop is approximately 0,3 V and at the rated output approximately 0,45 V. All models are fitted with a compensation diode that can be used to slightly increase the output voltage of the alternator. This compensates for the voltage drop over the diodes in the isolator. Please see Victron Energy’s ‘Energy Unlimited’ or ask for specialist advice when installing a diode isolator. Simply inserting the isolator in the cabling between the alternator and the batteries will slightly reduce charge voltage. The result can be that batteries are not charged to the full 100% and age prematurely. Alternator energize input Some alternators need DC voltage on the B+ output to start charging. Obviously, DC will be present when the alternator is directly connected to a battery. Inserting a Diode or FET splitter will however prevent any return voltage/current from the batteries to the B+, and the alternator will not start. The new ‘AC’ diode isolators feature a special current limited energize input that will power the B+ when the engine run/stop switch is closed. Brand Victron Energy Manufacturer Part Number ARG080201000R Maximum Charge Current (A) 80 Maximum Alternator Current (A) 80 Number Of Batteries 2 Alternator Energize Input Yes Connection M6 Studs Compensation diode & Energize Connection 6.3mm Faston Dimensions H60 x W120 x D90mm Weight (kg) 0.6 Warranty 5 Years
£36.86 Exc. VAT
£44.23 Inc. VAT
In stock
Victron Victron Energy Argodiode 80-2SC Two Batteries 80A – ARG080202000R
The Argo Battery Isolators feature a low voltage drop thanks to the use of Schottky diodes: at low current the voltage drop is approximately 0,3 V and at the rated output approximately 0,45 V. All models are fitted with a compensation diode that can be used to slightly increase the output voltage of the alternator. This compensates for the voltage drop over the diodes in the isolator. Please see Victron Energy’s ‘Energy Unlimited’ or ask for specialist advice when installing a diode isolator. Simply inserting the isolator in the cabling between the alternator and the batteries will slightly reduce charge voltage. The result can be that batteries are not charged to the full 100% and age prematurely. Alternator energize input Some alternators need DC voltage on the B+ output to start charging. Obviously, DC will be present when the alternator is directly connected to a battery. Inserting a Diode or FET splitter will however prevent any return voltage/current from the batteries to the B+, and the alternator will not start. The new ‘AC’ diode isolators feature a special current limited energize input that will power the B+ when the engine run/stop switch is closed. Brand Victron Energy Manufacturer Part Number ARG080202000R Maximum Charge Current (A) 80 Maximum Alternator Current (A) 80 Number Of Batteries 2 Alternator Energize Input No Connection M6 Studs Compensation diode & Energize connection 6.3mm Faston Dimensions H60 x W120 x D75mm Weight (kg) 0.5 Warranty 5 Years
£23.94 Exc. VAT
£28.73 Inc. VAT
In stock
Victron Victron Energy Argodiode 180-3AC Three Batteries 180A – ARG180301020
The Argo Battery Isolators feature a low voltage drop thanks to the use of Schottky diodes: at low current the voltage drop is approximately 0,3 V and at the rated output approximately 0,45 V. All models are fitted with a compensation diode that can be used to slightly increase the output voltage of the alternator. This compensates for the voltage drop over the diodes in the isolator. Please see Victron Energy’s ‘Energy Unlimited’ or ask for specialist advice when installing a diode isolator. Simply inserting the isolator in the cabling between the alternator and the batteries will slightly reduce charge voltage. The result can be that batteries are not charged to the full 100% and age prematurely. Alternator energize input Some alternators need DC voltage on the B+ output to start charging. Obviously, DC will be present when the alternator is directly connected to a battery. Inserting a Diode or FET splitter will however prevent any return voltage/current from the batteries to the B+, and the alternator will not start. The new ‘AC’ diode isolators feature a special current limited energize input that will power the B+ when the engine run/stop switch is closed Brand Victron Energy Manufacturer Part Number ARG180301020 GTIN 8719076019121 Maximum charge current 180A Maximum alternator current 180A Number Of Batteries 0003 Alternator Energize Input Yes Connection M8 Studs Compensation diode & Energize Connection 6.3mm Faston Dimensions H60 x W120 x D200mm Weight 1.5Kg Warranty 5 Years
£66.78 Exc. VAT
£80.14 Inc. VAT
In stock
Victron Victron Energy Argofet 100-2 Two Batteries 100A – ARG100201020R
In contrast with diode battery isolators, FET isolators have virtually no voltage loss. Voltage drop is less than 0,02 Volt at low current and averages 0,1 Volt at higher currents. When using ARGO FET Battery Isolators, there is no need to also increase the output voltage of the alternator. Care should taken however to keep cable lengths short and of sufficient cross section. Example: When a current of 100 A flows through a cable of 50 mm2 cross section (AWG 0) and 10 m length (30 ft), the voltage drop over the cable will be 0,26 Volt. Similarly a current of 50 A through a cable of 10 mm2 cross section (AWG 7) and 5 m length (15 ft) will result in a voltage drop of 0,35 Volt! Alternator energize input Some alternators need DC voltage on the B+ output to start charging. Obviously, DC will be present when the alternator is directly connected to a battery. Inserting a Diode or FET splitter will however prevent any return voltage/current from the batteries to the B+, and the alternator will not start. The new Argofet isolators have a special current limited energize input that will power the B+ when the engine run/stop switch is closed. Brand Victron Energy Manufacturer Part Number ARG100201020R GTIN 8719076019022 Maximum charge current 100A Maximum alternator current 100A Number Of Batteries 2 Connection M8 Bolts Dimensions H65 x W120 x D200mm Weight 1.4Kg Warranty 5 Years
£60.48 Exc. VAT
£72.58 Inc. VAT
In stock
Victron Victron Energy Blue Smart IP65 Charger 12V 25A 1 Output UK – BPC122531024
Benefits The battery is charged, smartly… to perfect condition The seven-step charging algorithm gets the best out of your battery. The charger gives the battery the power it needs, maintains its health, ensures better performance… and a longer life. Recovery of deeply-discharged ‘dead’ batteries Unlike other brands, the Blue Smart IP65 Charger will attempt to recharge a deeply-discharged battery by force-feeding it with a low current. Normal charging will then be resumed as soon as there is sufficient voltage across the battery terminals. Connect the battery with ease The charger comes with both crocodile clips and M8 eyelets – making it easy to connect to the battery. If you wish, you can leave it permanently connected. Check the status of your battery remotely The Blue Smart IP65 is equipped with built-in Bluetooth, so the status of the charger and the battery can be checked on a smartphone, tablet or laptop. All settings of the charger can be configured with the VictronConnect app. Features Water, dust and chemical resistant Seven step smart charge algorithm Recovery of fully discharged ‘dead’ batteries Automatic power supply function Severe cold performance: down to -30°C Several other battery life enhancing features Low power mode to charge smaller batteries Li-ion battery mode Setup and configure, readout of voltage and current by Bluetooth Smart Brand Victron Energy Manufacturer Part Number BPC122531024 GTIN 8719076051565 Voltage 12V Charge Current 25A Input Voltage 230V Number of Outputs 1 Protection Category IP65 (splash and dust proof) Efficiency 94% Bluetooth Enabled Yes Plug Type UK Dimensions H75 x W140 x D240mm Weight 1.9Kg Warranty 5 Years
£178.98 Exc. VAT
£214.78 Inc. VAT
In stock
Victron Victron Energy Blue Smart IP67 Charger 24V 5A 1 Output – BPC240513006
The Blue Smart IP67 Waterproof Charger is the new professional battery charger with built-in bluetooth. The Blue Smart IP67 Waterproof Charger can be used on devices in your workshop and on motor vehicles, such as (classic) cars; motorbikes; boats and camper-vans. Features Bluetooth Smart enabled The Blue Smart IP67 Charger is the wireless solution to monitor voltage and current, to change settings and to update the charger when new features become available. With Bluetooth, the functionality of the IP67 charger is enhanced and is similar to that of our IP22 and IP65 chargers. Completely encapsulated: waterproof, shockproof and ignition protected Water, oil or dirt will not damage the Blue Smart IP67 Charger. The casing is made of cast aluminium and the electronics are moulded in resin. The highest efficiency ever! Setting a new industry standard: with 92% efficiency or better, these chargers waste three to four times less heat. And once the battery is fully charged, power consumption reduces to less than a Watt, some five to ten times better than the industry standard. Adaptive 5-stage charge algorithm: bulk – absorption – recondition – float – storage The Blue Smart Charger features a microprocessor controlled ‘adaptive’ battery management. The ‘adaptive’ feature will automatically optimise the charging process relative to the way the battery is being used. Storage Mode: Less maintenance and aging when the battery is not in use The storage mode kicks in whenever the battery has not been subjected to discharge during 24 hours. In the storage mode float voltage is reduced to 2,2 V/cell (13,2 V for a 12 V battery) to minimise gassing and corrosion of the positive plates. Once a week the voltage is raised back to the absorption level to ‘equalize’ the battery. This feature prevents stratification of the electrolyte and sulphation, a major cause of early battery failure. Also charges Li-ion (LiFePO4) batteries LiFePO4 batteries are charged with a simple bulk – absorption – float algorithm. Protected against overheating Can be used in a hot environment such as a machine room. Output current will reduce as temperature increases up to 60°C, but the charger will not fail. Two LEDs for status indication Yellow LED: bulk charge (blinking fast), absorption (blinking slow), float (solid), storage (off) Green LED: power on. CLICK HERE FOR SPEC SHEET Brand Victron Energy Manufacturer Part Number BPC240513006 GTIN 8719076035947 Voltage 24V Charge Current 5A Input Voltage 230V Number of Outputs 1 Can Be Used As Power Supply Yes Protection Category IP67 Efficiency 94% Bluetooth Enabled Yes Plug Type CEE 7/7 Dimensions H85 x W211 x D60mm Weight 1.8Kg Warranty 5 Years
£86.54 Exc. VAT
£103.85 Inc. VAT
In stock
Victron Victron Energy Phoenix Inverter 12V 375VA VE.Direct UK – PIN123750400
Features VE.Direct communication port The VE.Direct port can be connected to: A computer (VE.Direct to USB interface cable needed) Apple and Android smartphones, tablets, MacBook’s and other devices (VE.Direct Bluetooth Smart dongle needed) Fully configurable: Low battery voltage alarm trip and reset levels Low battery voltage cut-off and restart levels Dynamic cut-off: load dependent cut-off level Output voltage 210 – 245V Frequency 50 Hz or 60 Hz ECO mode on/off and ECO mode sense level Monitoring: In- and output voltage, % load and alarms Proven reliability The full bridge plus toroidal transformer topology has proven its reliability over many years. The inverters are short circuit proof and protected against overheating, whether due to overload or high ambient temperature. High start-up power Needed to start loads such as power converters for LED lamps, halogen lamps or electric tools. ECO mode When in ECO mode, the inverter will switch to standby when the load decreases below a preset value (min load: 15W). Once in standby the inverter will switch on for a short period (adjustable, default: every 2,5 seconds). If the load exceeds a preset level, the inverter will remain on. Remote on/off A remote on/off switch can be connected to a two pole connector, or between battery plus and the left hand contact of the two pole connector. DC connection with screw terminals No special tools needed for installation. Brand Victron Energy Manufacturer Part Number PIN123750400 GTIN 8719076034001 Voltage 12V Cont. Output Power at 25°C 375VA Peak Power 700W Output AC Voltage 230V Protection Category IP21 Efficiency 89% Bluetooth Enabled No Plug Type UK Dimensions H86 x W165 x D260mm Weight 3Kg Warranty 5 Years
£115.86 Exc. VAT
£139.03 Inc. VAT
In stock
Victron Victron Energy Inverter RS 48V 6000VA Smart – PIN482600000
The inverter is equipped with a display to read out battery and inverter details. These parameters can also be read out via Bluetooth by the VictronConnect app. In addition to this, the inverter has a VE.Can Port, for connection to a GX device for system monitoring. Features Light weight, efficient and quiet Thanks to high frequency technology and a new design this powerful inverter weighs only 11kg. In addition to this it has an excellent efficiency, low standby power, and a very quiet operation. Display and Bluetooth The display reads battery and inverter parameters. The same parameters can be accessed with a smartphone or other Bluetooth enabled device. In addition, Bluetooth can be used to set up the system and to change settings with VictronConnect. VE.Can and VE.Direct port For connection to a GX device for system monitoring, data logging, and remote firmware updates. I/O Connections Programmable Relay, temperature sensor and voltage sensor connections. The remote input can also be configured to accept the Victron smallBMS. Brand Victron Energy Manufacturer Part Number PIN482600000 GTIN 8719076046059 Voltage 48V Cont. Output Power at 25°C 6000VA Peak Power 9kW for 3 seconds Output AC Voltage 230V Protection Category IP21 Bluetooth Enabled Yes Dimensions H425 x W440 x D125mm Weight 11Kg Warranty 5 Years
£799.00 Exc. VAT
£958.80 Inc. VAT
1 in stock
Victron Victron Energy MultiPlus 48V 2000VA 25-32A VE.Bus – PMP482200000
Features Multifunctional, with intelligent power management The MultiPlus is a powerful true sine wave inverter, a sophisticated battery charger that features adaptive charge technology, and a high-speed AC transfer switch in a single compact enclosure. Next to these primary functions, the MultiPlus has several advanced features, as outlined below. Parallel operation and three phase capability Up to six Multis can operate in parallel to achieve higher power output. In addition to parallel connection, three units can be configured for three-phase output. PowerControl – Dealing with limited generator, shore side or grid power With the Multi Control Panel a maximum generator or shore current can be set. The MultiPlus will then take account of other AC loads and use whatever is extra for charging, thus preventing the generator or shore supply from being overloaded. PowerAssist – Boosting the capacity of shore or generator power This feature takes the principle of PowerControl to a further dimension. It allows the MultiPlus to supplement the capacity of the alternative source. Where peak power is so often required only for a limited period, the MultiPlus will make sure that insufficient shore or generator power is immediately compensated for by power from the battery. When the load reduces, the spare power is used to recharge the battery. Four stage adaptive charger and dual bank battery charging The main output provides a powerful charge to the battery system by means of advanced ‘adaptive charge’ software. The software fine-tunes the three-stage automatic process to suit the condition of the battery, and adds a fourth stage for long periods of float charging. The adaptive charge process is described in more detail on the Phoenix Charger datasheet and on our website, under Technical Information. In addition to this, the MultiPlus will charge a second battery using an independent trickle charge output intended for a main engine or generator starter battery. High start-up power Needed to start high inrush loads such as power converters for LED lamps, halogen lamps or electric tools. Search Mode When Search Mode is ‘on’, the power consumption of the inverter in no-load operation is decreased by approx. 70%. In this mode the Multi, when operating in inverter mode, is switched off in case of no load or very low load, and switches on every two seconds for a short period. If the output current exceeds a set level, the inverter will continue to operate. If not, the inverter will shut down again. Programmable relay By default, the programmable relay is set as an alarm relay, i.e. the relay will de-energise in the event of an alarm or a pre-alarm (inverter almost too hot, ripple on the input almost too high, battery voltage almost too low). Remote on / off / charger on Three pole connector. On-site system configuring, monitoring and control After installation, the MultiPlus is ready to go. Some settings can be changed with DIP switches. 500/800/1200VA models: remote switch / battery charge voltage / inverter frequency /search mode. 1600/2000VA models: battery charge voltage /search mode. For more settings use VE-Config or the VE.Bus Smart dongle. Remote configuring and monitoring Install a Cerbo GX or other GX product to connect to the internet. Operational data can be stored and displayed on our VRM (Victron Remote Management) website, free of charge. When connected to the internet, systems can be accessed remotely, and settings can be changed. Brand Victron Energy Manufacturer Part Number PMP482200000 GTIN 8719076049470 Voltage 48V Cont. output power at 25ºC 2000VA Peak Power 3500W Output AC Voltage 230V Transfer Switch 35A Charge Current House Battery 25A Protection Category IP22 Efficiency 95% Bluetooth Compatible No Dimensions H506 x W236 x D147mm Weight 15.5Kg Warranty 5 Years
£322.20 Exc. VAT
£386.64 Inc. VAT
In stock
Victron Victron Energy MultiPlus 24V 2000VA 50A 32A VE.Bus – PMP242200000
Features Two AC Outputs The main output has no break functionality. The MultiPlus takes over the supply to the connected loads in the event of a grid failure or when shore/generator power is disconnected. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption. The second output is live only when AC is available on the input of the MultiPlus. Loads that should not discharge the battery, like a water heater for example can be connected to this output (second output available on models rated at 3 kVA and more). Virtually unlimited power thanks to parallel operation Up to 6 Multis can operate in parallel to achieve higher power output. Six 24/5000/120 units, for example, will provide 25 kW / 30 kVA output power with 720 Amps charging capacity. Three phase capability In addition to parallel connection, three units of the same model can be configured for three phase output. But that’s not all: up to 6 sets of three units can be parallel connected for a huge 75 kW / 90 kVA inverter and more than 2000 Amps charging capacity. PowerControl – Dealing with limited generator, shore side or grid power The MultiPlus is a very powerful battery charger. It will therefore draw a lot of current from the generator or shore side supply (nearly 10 A per 5 kVA Multi at 230 VAC). With the Multi Control Panel a maximum generator or shore current can be set. The MultiPlus will then take account of other AC loads and use whatever is extra for charging, thus preventing the generator or shore supply from being overloaded. PowerAssist – Boosting the capacity of shore or generator power This feature takes the principle of PowerControl to a further dimension. It allows the MultiPlus to supplement the capacity of the alternative source. Where peak power is so often required only for a limited period, the MultiPlus will make sure that insufficient shore or generator power is immediately compensated for by power from the battery. When the load reduces, the spare power is used to recharge the battery. Solar energy: AC power available even during a grid failure The MultiPlus can be used in off grid as well as grid connected PV and other alternative energy systems. Loss of mains detection software is available. System configuring In case of a stand-alone application, if settings have to be changed, this can be done in a matter of minutes with a DIP switch setting procedure. Parallel and three phase applications can be configured with VE.Bus Quick Configure and VE.Bus System Configurator software. CLICK HERE FOR SPEC SHEETS Brand Victron Energy Manufacturer Part Number PMP242200000 GTIN 8719076052173 Voltage 24V Cont. Output Power at 25°C 2000VA Peak Power 3500W Output AC Voltage 230V Transfer Switch 35A Charge Current House Battery 50A Charge Current Starter Battery 1A Protection Category IP21 Efficiency 94% Bluetooth Compatible No Dimensions H500 x W225 x D135mm Weight 13.5Kg Warranty 5 Years
£516.66 Exc. VAT
£619.99 Inc. VAT
In stock
