Quick Order

Adjustable output voltage: can also be used as a battery chargerFor example to charge a 12 Volt starter or accessory battery in an otherwise 24V system.  All models are short circuit proof and can be paralleled to increase output currentAn unlimited number of units can be connected in parallel.  IP43 protectionWhen installed with the screw terminals oriented downwards.  Screw terminalsNo special tools needed for installation. Input fuseOn 12V and 24V input models only. Brand Victron Energy Manufacturer Part Number ORI482441110 Input Voltage Range 40-70V Under Voltage Shutdown 28V Under Voltage Restart 30V Nominal Output Voltage 24.2V Output Voltage Adjust Range 20-30V Short Circuit Output Current 40A Cont. Output Power at 25°C 430W DC Connection Screw Terminals Protection Category IP43 Dimensions H130 x W186 x D70mm Weight (kg) 1.6 Warranty 5 Years

Read more less

For use in dual battery systems in vehicles or on boats where the (smart) alternator and the start battery are used to charge the service battery. The unit can be monitored and programmed via Bluetooth and can be remotely controlled via a remote on/off switch and has an engine running detection mechanism. The Orion Tr-Smart charger can be used in 12V or 24V systems and is suitable for both lead acid and lithium batteries. Models are available up to 400W and unlimited multiple units can be connected in parallel to increase output power. Suitable for high temperatures up to 55°C with a full rated output up to 40°C. Features Bluetooth Smart enabled Any Bluetooth enabled smart phone, tablet or other device can be used to monitor, to change settings and to update the charger when new software features become available. Fully programmable Battery charge algorithm (configurable) or fixed output. Smart alternator compatibility: engine running detection mechanism. Adaptive 3-stage charge algorithm: bulk – absorption – float For lead acid batteries it is important that during shallow discharges the absorption time is kept short in order to prevent overcharging of the battery. After a deep discharge the absorption time is automatically increased to make sure that the battery is completely recharged.  For lithium batteries absorption time is fixed, default 2 hours. Alternatively, a fixed output voltage can be chosen. Remote on-off A remote on/off switch or relay contact can be connected to a two-pole connector. Alternatively, the H terminal (right) of the two-pole connector can be switched to battery plus, or the L terminal (left) of the two pole connector can be switched to battery minus (or the chassis of a vehicle, for example). All models are short circuit proof and can be paralleled to increase output current An unlimited number of units can be connected in parallel. High temperature protected The output current will reduce at high ambient temperature. IP43 protection When installed with the screw terminals oriented downwards. Screw terminals No special tools needed for installation. Input fuse (not replaceable) Brand Victron Energy Manufacturer Part Number ORI122424120 Warranty 5 Years Weight (kg) 1.3 Efficiency 88% Dimensions H130 x W186 x D70mm Input Voltage Range 8-17 V Protection Category IP43 Nominal Output Voltage 24.2 V Output Voltage Adjust Range 20-30 V Under Voltage Shutdown 7 V Under Voltage Restart 7.5 V DC Connection Screw Terminals Cont. Output Power at 25°C (W) 280 Cont. Output Power at 40°C (W) 240

Read more less

  Brand Victron Energy Manufacturer Part Number SHP302502500 Current Rating (A) 16 Connector Type Moulded IEC 60309 3-Pole Cable Type H07BQ-F 3x 2,50mm² Plug Type Moulded IEC 60309 2p+E Cable Length 25m Weight (kg) 4.3 Warranty 5 Years Country of Manufacture Netherlands

Read more less

The supply could be the grid, a generator or two stacked inverters. Some of the loads connected are 240V, others are 120V. On each 120V leg the load should not exceed 30A. The problem is that as soon as 120V loads are connected, the two legs will show a different current. This is because the 120V loads on the two legs will never be balanced. A 120V 1200W hairdryer, for example, will draw 10A from one leg. A 120V washing machine could even draw in excess of 20A from one leg. Between the two legs the difference in current, or current unbalance, will therefore often be 20A or more. This means that the 30A supply will not be used up to its full potential. By the time one leg draws 30A, the other leg may be drawing no more than 10A, and increasing the 240V load, for example, will result in an overload of one leg while the other leg still has spare capacity. Theoretically, the total power that can be drawn from a 30A 120/240V supply is 30 x 240 = 7,2 kVA. In case of 20A unbalance, the practical maximum will be 30 x 120 + 10 x120 = 4,8kVA, or 67% of the theoretical maximum. The solution is an Autotransformer. By leaving the neutral of the split phase supply unused, and connecting an Autotransformer to create a new neutral, as shown in figure 1, any load unbalance is ‘absorbed’ by the Autotransformer. In case of a 30A supply, the load can be increased to 7,2kVA, and a 20A load unbalance will result in one leg supplying 40A, and the other leg 20A. The 20A difference will flow through the neutral and the windings of the Autotransformer. The current through both 120V wires of the split phase supply will be 30A. Brand Victron Energy Manufacturer Part Number ITR000100101 Input/Output Voltage 120/240V Input Circuit Breaker 100A, two pole Frequency (Hz) 50/60 Maximum 240V feed through current 100A Ingress Protection IP21 Dimensions (Including Terminals) H425 x W214 x D110 mm Weight (kg) 13.5 Warranty 5 Years

Read more less

Brand Victron Energy Manufacturer Part Number SCC010020020 GTIN 8719076025351 Battery Voltage 12/24V with automatic system voltage detection Rated Charge Current 20A Maximum Solar Voltage 28V / 55V Grounding Common positive IP Rating IP20 Dimensions H70 x W133 x D33.5mm Weight 0.15Kg Warranty 5 Years

Read more less

  Brand Victron Energy Manufacturer Part Number SCC010020060 GTIN 8719076046219 Battery Voltage 12/24 V with automatic system voltage detection [for LiFePO4 no automatic system voltage detection] Rated Charge Current 20A Second battery output Yes Load Output 2 USB ports 5V/2A Grounding Common negative Battery Temperature Sensor Yes, remote sensor [included] Protection Category IP20 Dimensions H101.5 x W184.0 x D47.1mm Weight 0.3Kg Warranty 5 Years

Read more less

Features Ultra-fast Maximum Power Point Tracking (MPPT) Especially in case of a clouded sky, when light intensity is changing continuously, an ultra-fast MPPT controller will improve energy harvest by up to 30% compared to PWM charge controllers and by up to 10% compared to slower MPPT controllers.   Load output Over-discharge of the battery can be prevented by connecting all loads to the load output. The load output will disconnect the load when the battery has been discharged to a pre-set voltage. Alternatively, an intelligent battery management algorithm can be chosen: see Battery Life. The load output is short circuit proof. Some loads (especially inverters) can best be connected directly to the battery, and the inverter remote control connected to the load output. A special interface cable may be needed, please see the manual.   Battery Life: intelligent battery management When a solar charge controller is not able to recharge the battery to its full capacity within one day, the result is often that the battery will continually be cycled between a ‘partially charged’ state and the ‘end of discharge’ state. This mode of operation (no regular full recharge) will destroy a lead-acid battery within weeks or months. The Battery Life algorithm will monitor the state of charge of the battery and, if needed, day by day slightly increase the load disconnect level (i.e. disconnect the load earlier) until the harvested solar energy is sufficient to recharge the battery to nearly the full 100%. From that point onwards the load disconnect level will be modulated so that a nearly 100% recharge is achieved about once every week.   Programming, real-time data and history display options Color Control GX or other GX devices: see the Venus documents on our website. A smartphone or other Bluetooth-enabled device: VE.Direct Bluetooth Smart dongle needed. Brand Victron Energy Manufacturer Part Number SCC010010050R GTIN 8719076025306 Battery Voltage 12/24V Auto Select Rated Charge Current 10A Nominal PV Power, 12V 145W Nominal PV Power, 24V 290W Max. PV Short Circuit Current 10A Maximum PV Open Circuit Voltage 75V Efficiency 98% Charge Algorithm Multi-stage adaptive Data Communication Port VE.Direct IP Rating IP43 (electronic components), IP22 (connection area) Dimensions H100 x W113 x D40mm Weight 0.5Kg Warranty 5 Years

Read more less

Features Ultra-fast Maximum Power Point Tracking (MPPT) Especially in case of a clouded sky, when light intensity is changing continuously, an ultra-fast MPPT controller will improve energy harvest by up to 30% compared to PWM charge controllers and by up to 10% compared to slower MPPT controllers. Advanced Maximum Power Point Detection in case of partial shading conditions If partial shading occurs, two or more maximum power points (MPP) may be present on the power-voltage curve. Conventional MPPTs tend to lock to a local MPP, which may not be the optimum MPP. The innovative BlueSolar algorithm will always maximize energy harvest by locking to the optimum MPP. Outstanding conversion efficiency No cooling fan. Maximum efficiency exceeds 99%. Flexible charge algorithm Fully programmable charge algorithm, and eight preprogrammed algorithms, selectable with a rotary switch (see manual for details). Extensive electronic protection Over-temperature protection and power derating when temperature is high. PV short circuit and PV reverse polarity protection. PV reverse current protection. Internal temperature sensor Compensates absorption and float charge voltage for temperature. Optional external battery voltage, temperature and current sensing via Bluetooth A Smart Battery Sense or a BMV-712 Smart Battery Monitor can be used to communicate battery voltage and temperature (and current, in case of a BMV 712 or a SmartShunt) to one or more BlueSolar Charge Controllers. (VE.Direct Bluetooth Smart dongle needed) VE.Can: the multiple controller solution Up to 25 units can be synchronised with VE.Can VE.Direct or VE.Can For a wired data connection to a Color Control GX, other GX products, PC or other devices Remote on-off To connect for example to a VE.BUS BMS. Programmable relay Can be programmed to trip on an alarm, or other events. Optional: SmartSolar pluggable LCD display Simply remove the rubber seal that protects the plug on the front of the controller, and plug-in the display. Brand Victron Energy Manufacturer Part Number SCC115110420 GTIN 8719076049852 Battery Voltage 12 / 24 / 48V Auto Select (software tool needed to select 36V) Rated Charge Current 100A Nominal PV Power, 12V 1450W Nominal PV Power, 24V 4350W Max. PV Short Circuit Current 70A Maximum PV Open Circuit Voltage 150V absolute maximum coldest conditions | 145V start-up and operating maximum Efficiency 98% Charge Algorithm Multi-stage adaptive Data Communication Port VE.Can Protection Category IP43 (electronic components), IP22 (connection area) Dimensions H216 x W295 x D103mm Weight 3Kg Warranty 5 Years

Read more less

The Cyrix-Li-Charge will disengage immediately whenever its control input becomes free floating, signalling cell over voltage or cell over temperature. In general a cell over voltage alarm will reset shortly after charging has been stopped. The Cyrix will then reconnect the charger after a delay of 3 seconds. After two attempts to reengage with 3 seconds delay, the delay increases to 10 minutes. Whenever battery voltage is less than 13,5V (resp. 27V or 54V), the Cyrix will disengage with a delay of 1 hour. Note 1: In case of zero discharge current, or a small discharge current, the Cyrix will not disengage shortly after the charger has been switched off and/or disconnected, because battery voltage will remain higher than 13,5V. Note 2: If, after the Cyrix has disengaged, the output of the battery charger immediately increases to 13,7V or more, the Cyrix will re-engage, with 3 seconds delay Brand Victron Energy Manufacturer Part Number CYR020120430 Voltage 24/48 Continuous current & Breaking capacity at 12V or 24V 120A Breaking Capacity at 48V 40A Current Consumption When Open 4 mA Protection Category IP54 Dimensions H46 x W46 x D80mm Weight (kg) 0.11 Warranty 5 Years

Read more less

Features Battery ‘fuel gauge’, time-to-go indicator, and much more The remaining battery capacity depends on the ampere-hours consumed, discharge current, temperature and the age of the battery. Complex software algorithms are needed to take all these variables into account. Next to the basic display options, such as voltage, current and ampere-hours consumed, the BMV-700 series also displays state of charge, time to go, and power consumption in Watts. Easy to install All electrical connections are to the quick connect PCB on the current shunt. The shunt connects to the monitor with a standard RJ12 telephone cable. Included: RJ 12 cable (10 m) and battery cable with fuse (2 m); no other components needed. Also included are a separate front bezel for a square or round display appearance, a securing ring for the rear mounting and screws for the front mounting. BMV-702 additional features Additional input to measure voltage (of a second battery), temperature or midpoint voltage, and corresponding alarm and relay settings.   Standard features Battery voltage, current, power, ampere-hours consumed and state of charge Remaining time at the current rate of discharge Programmable visual and audible alarm Programmable relay, to turn off non critical loads or to run a generator when needed 500 Amp quick connect shunt and connection kit Shunt selection capability up to 10.000 Amps VE.Direct communication port Stores a wide range of historical events, which can be used to evaluate usage patterns and battery health Wide input voltage range: 6,5 – 95V High current measurement resolution: 10 mA (0,01A) Low current consumption: 2,9Ah per month (4mA) @12V and 2,2Ah per month (3mA) @ 24V Brand Victron Energy Manufacturer Part Number BAM010702000R Supply Voltage Range 6.5-95 VDC Battery Capacity (Ah) 1-9999 Temperature Sensor Optional VE.Direct Communication Port Yes Protection Category IP55 Front Bezel 69 x 69mm Body Diameter & Depth 52 x 31mm Warranty 5 Years

Read more less

Brand Victron Energy Manufacturer Part Number ASS000100000 Warranty 5 Years

Read more less

  Brand Victron Energy Manufacturer Part Number ASS030560100 Cable Length 1m Warranty 5 Years

Read more less

The batteries can be connected in parallel. Series connection is not allowed.  Features Integrated BMS and safety switch The SuperPack batteries are extremely easy to install, needing no additional components. The internal switch will disconnect the battery in case of over discharge, over charge or high temperature. Abuse proof A lead-acid battery will fail prematurely due to sulfation: If it operates in deficit mode during long periods of time (i.e. if the battery is rarely, or never at all, fully charged). If it is left partially charged or worse, fully discharged. A Lithium-Ion battery does not need to be fully charged. Service life even slightly improves in case of partial charge instead of a full charge. This is a major advantage of Li-ion compared to lead-acid. The SuperPack batteries will cut-off the charge or discharge current when the maximum ratings are exceeded. Efficient In several applications (especially off-grid solar), energy efficiency can be of crucial importance. The round-trip energy efficiency (discharge from 100% to 0% and back to 100% charged) of the average lead-acid battery is 80%. The round-trip energy efficiency of a Li-ion battery is 92%. The charge process of lead-acid batteries becomes particularly inefficient when the 80% state of charge has been reached, resulting in efficiencies of 50% or even less in solar systems where several days of reserve energy are required (battery operating in 70% to 100% charged state). In contrast, a Li-ion battery will still achieve 90% efficiency even under shallow discharge conditions. Can be connected in parallel The batteries can be connected in parallel. Series connection is not allowed. Use in upright position only. Brand Victron Energy Manufacturer Part Number BAT512060705 Voltage 12.8 Capacity (C20) 60 Terminal Type M6 Terminal Layout LH+ Dimensions (Including Terminals) L229 x W138 x D213mm Weight (kg) 9.5 Warranty 3 Years Battery Technology Lithium

Read more less

 The SuperPack batteries are extremely easy to install, not needing any additional components. The internal switch will disconnect the battery in case of over discharge, over charge or high temperature. The batteries can be connected in parallel. Series connection is not allowed.    Features Integrated BMS and safety switch The SuperPack batteries are extremely easy to install, needing no additional components. The internal switch will disconnect the battery in case of over discharge, over charge or high temperature. Abuse proof A lead-acid battery will fail prematurely due to sulfation: If it operates in deficit mode during long periods of time (i.e. if the battery is rarely, or never at all, fully charged). If it is left partially charged or worse, fully discharged. A Lithium-Ion battery does not need to be fully charged. Service life even slightly improves in case of partial charge instead of a full charge. This is a major advantage of Li-ion compared to lead-acid. The SuperPack batteries will cut-off the charge or discharge current when the maximum ratings are exceeded. Efficient In several applications (especially off-grid solar), energy efficiency can be of crucial importance. The round-trip energy efficiency (discharge from 100% to 0% and back to 100% charged) of the average lead-acid battery is 80%. The round-trip energy efficiency of a Li-ion battery is 92%. The charge process of lead-acid batteries becomes particularly inefficient when the 80% state of charge has been reached, resulting in efficiencies of 50% or even less in solar systems where several days of reserve energy are required (battery operating in 70% to 100% charged state). In contrast, a Li-ion battery will still achieve 90% efficiency even under shallow discharge conditions. Can be connected in parallel The batteries can be connected in parallel. Series connection is not allowed. Use in upright position only. Brand Victron Energy Manufacturer Part Number BAT524050705 Voltage 25.6 Capacity (C20) 50 Terminal Type M8 Terminal Layout LH+ Dimensions (Including Terminals) L330 x W171 x H220mm Weight (kg) 14 Warranty 3 Years Battery Technology Lithium

Read more less

 Features A truly innovative battery The AGM Super Cycle batteries are the result of recent battery electrochemistry developments. The paste of the positive plates is less sensitive to softening, even in case of repeated 100% discharge of the battery, and new additives to the electrolyte reduce sulfation in case of deep discharge. Exceptional 100% depth of discharge (DoD) performance Tests have shown that the Super Cycle battery does withstand at least three hundred 100% DoD cycles. The tests consist of a daily discharge to 10,8V with I = 0,2C20, followed by approximately two hours rest in discharged condition, and then a recharge with I = 0,2C20. The two hours rest period in discharged condition will damage most batteries within 100 cycles, but not the Super Cycle battery. We recommend the Super Cycle battery for applications where an occasional discharge to 100% DoD, or frequent discharge to 60- 80% DoD is expected. Smaller and lighter An additional advantage of the new chemistry is a slightly smaller size and less weight compared to our standard deep cycle AGM batteries. Low internal resistance The internal resistance is also slightly lower compared to our standard deep cycle AGM batteries Brand Victron Energy Manufacturer Part Number BAT412015080 Voltage 12 Capacity (C20) 15 Terminal Type Faston Terminal Layout Side Dimensions (Including Terminals) L151 x W100 x H103mm Weight (kg) 4.1 Warranty 2 Years Battery Technology AGM Battery Application Super Cycle

Read more less

  Brand Victron Energy Manufacturer Part Number BPC900300014 Warranty 5 Years

Read more less

Brand Victron Energy Manufacturer Part Number BPC900400014 Warranty 5 Years

Read more less

Brand Victron Energy Manufacturer Part Number BPC920100200 Dimensions H134 x W145 x D72mm Warranty 5 Years

Read more less

  (Charger and accessories not included) Brand Victron Energy Manufacturer Part Number BPC940100100 Dimensions H295 x W350 x D105 mm Warranty 5 Years

Read more less

Features   Bluetooth Smart The Blue Smart IP22 Charger is the wireless solution to monitor voltage and current, to change settings and to update the charger when new features become available.   High efficiency With up to 94% efficiency, these chargers generate up to four times less heat when compared to the industry standard. And once the battery is fully charged, power consumption reduces to 0,5 Watt, some five to ten times better than the industry standard.   Adaptive 6-stage charge algorithm: test – bulk – absorption – recondition – float – storage The Blue Smart Charger features a microprocessor controlled ‘adaptive’ battery management. The adaptive feature will automatically optimize the charging process relative to the way the battery is being used.   Storage Mode: less maintenance and aging when the battery is not in use The storage mode kicks in whenever the battery has not been subjected to discharge during 24 hours. In the storage mode float voltage is reduced to 2,2V/cell (13,2V for a 12V battery) to minimize gassing and corrosion of the positive plates. Once a week the voltage is raised back to the absorption level to ‘equalize’ the battery. This feature prevents stratification of the electrolyte and sulfation, a major cause of early battery failure.   Also charges Li-ion (LiFePO4) batteries LiFePO4 batteries are charged with a simple bulk – absorption – float algorithm.   NIGHT and LOW setting When in NIGHT or LOW mode, the output current is reduced to max. 50% of the nominal output and the charger will be totally noiseless. The NIGHT mode automatically ends after 8 hours. The LOW mode can be ended manually.   Protected against overheating Output current will reduce as temperature increases up to 50°C, but the Blue Smart Charger will not fail.   Eleven LEDs for status indication Charge algorithm: TEST / BULK / ABSORPTION / RECONDITION / FLOAT / STORAGE / READY. MODE button to set: NORMAL (14,4V) / HIGH (14,7V) / RECONDITION / LI-ION. Brand Victron Energy Manufacturer Part Number BPC123048022 GTIN 8719076052425 Voltage 12 Charger Amps 30A Outputs 3 Efficiency 93% Plug Type UK IP Rating IP22 Dimensions H235 x W108 x D65mm Weight 1.3Kg Warranty 5 Years

Read more less

Features   Bluetooth Smart The Blue Smart IP22 Charger is the wireless solution to monitor voltage and current, to change settings and to update the charger when new features become available.   High efficiency With up to 94% efficiency, these chargers generate up to four times less heat when compared to the industry standard. And once the battery is fully charged, power consumption reduces to 0,5 Watt, some five to ten times better than the industry standard.   Adaptive 6-stage charge algorithm: test – bulk – absorption – recondition – float – storage The Blue Smart Charger features a microprocessor controlled ‘adaptive’ battery management. The adaptive feature will automatically optimize the charging process relative to the way the battery is being used.   Storage Mode: less maintenance and aging when the battery is not in use The storage mode kicks in whenever the battery has not been subjected to discharge during 24 hours. In the storage mode float voltage is reduced to 2,2V/cell (13,2V for a 12V battery) to minimize gassing and corrosion of the positive plates. Once a week the voltage is raised back to the absorption level to ‘equalize’ the battery. This feature prevents stratification of the electrolyte and sulfation, a major cause of early battery failure.   Also charges Li-ion (LiFePO4) batteries LiFePO4 batteries are charged with a simple bulk – absorption – float algorithm.   NIGHT and LOW setting When in NIGHT or LOW mode, the output current is reduced to max. 50% of the nominal output and the charger will be totally noiseless. The NIGHT mode automatically ends after 8 hours. The LOW mode can be ended manually.   Protected against overheating Output current will reduce as temperature increases up to 50°C, but the Blue Smart Charger will not fail.   Eleven LEDs for status indication Charge algorithm: TEST / BULK / ABSORPTION / RECONDITION / FLOAT / STORAGE / READY. MODE button to set: NORMAL (14,4V) / HIGH (14,7V) / RECONDITION / LI-ION.   Brand Victron Energy Manufacturer Part Number BPC241647022 GTIN 8719076052494 Voltage Charger Amps 16A Outputs 1 Efficiency 94% Plug Type UK IP Rating IP22 Dimensions H235 x W108 x D65mm Weight 1.3Kg Warranty 5 Years

Read more less

Features Quality without compromise Aluminium epoxy powder coated cases with drip shield and stainless steel fixings withstand the rigors of an adverse environment: heat, humidity and salt air. Circuit boards are protected with an acrylic coating for maximum corrosion resistance. Temperature sensors ensure that power components will always operate within specified limits, if needed by automatic reduction of output current under extreme environmental conditions.   Universal 90-265V AC input voltage range and also suitable for DC supply (AC-DC and DC-DC operation) All models will operate without any adjustment needed over a 90 to 265 Volt input voltage range, whether 50 Hz or 60 Hz. The chargers also accept a 90-400 V DC supply.   Three outputs that each can supply the full output current Three isolated outputs to simultaneously charge 3 battery banks. Each output is capable to supply the full rated current.   Three-stage charging, with temperature compensation The Centaur charges at bulk rate until the output has reduced to 70% of the rated Amps, at which a 4 hour timer begins. After the timed period the charger switches to float rate. An internal temperature sensor is used to compensate the charge voltage with – 2 mV/ºC (– 1 mV/ºF) per cell. A DIP switch is available to select the optimum charge/float voltages for Flooded Lead-acid, Gel or AGM batteries. Brand Victron Energy Manufacturer Part Number CCH012040000 Voltage 12 Charger Amps 40 Recommended Battery Capacity 160 – 400Ah Battery Connection M8 Studs Outputs 3 IP Rating IP20 Dimensions H426 x W239 x D135mm Weight (kg) 5 Warranty 5 Years

Read more less

Crucially, and unlike many other products that state universal input, the Centaur range will maintain full output power within the entire specified range. Other features include fully automatic three stage charge characteristic that ensures batteries are fully charged every time and three isolated charge outputs for multi battery configurations to suit the majority of typical installations. The range spans 12V and 24V models from 16A through to 100A.   Features Quality without compromise Aluminium epoxy powder coated cases with drip shield and stainless steel fixings withstand the rigors of an adverse environment: heat, humidity and salt air. Circuit boards are protected with an acrylic coating for maximum corrosion resistance. Temperature sensors ensure that power components will always operate within specified limits, if needed by automatic reduction of output current under extreme environmental conditions.   Universal 90-265V AC input voltage range and also suitable for DC supply (AC-DC and DC-DC operation) All models will operate without any adjustment needed over a 90 to 265 Volt input voltage range, whether 50 Hz or 60 Hz. The chargers also accept a 90-400 V DC supply.   Three outputs that each can supply the full output current Three isolated outputs to simultaneously charge 3 battery banks. Each output is capable to supply the full rated current.   Three-stage charging, with temperature compensation The Centaur charges at bulk rate until the output has reduced to 70% of the rated Amps, at which a 4 hour timer begins. After the timed period the charger switches to float rate. An internal temperature sensor is used to compensate the charge voltage with – 2 mV/ºC (– 1 mV/ºF) per cell. A DIP switch is available to select the optimum charge/float voltages for Flooded Lead-acid, Gel or AGM batteries.   Brand Victron Energy Manufacturer Part Number CCH024060000 Voltage 24 Charger Amps 60 Outputs 3 Recommended Battery Capacity 240 – 600Ah Battery Connection M8 Studs IP Rating IP20 Dimensions H505 x W255 x x H130mm Weight (kg) 12 Warranty 5 Years

Read more less

  Brand Victron Energy Manufacturer Part Number ADA500100100 GTIN 8719076048640 Warranty 5 Years Country of Manufacture India

Read more less

Brand Victron Energy Manufacturer Part Number BPP900100200 Warranty 5 Years

Read more less

The EM24 is for 3 phase monitoring only. To measure the power and energy of the whole application at the distribution box. Or to measure the output of a PV Inverter, to display the data on the Color Control GX. The Energy Meter can be used as a: Grid meter, and used as control input for an ESS System. Measure the output of a PV Inverter Measure the output of a AC Genset The meter is connected to the Color Control GX. There are two options in its wiring: Direct connection, either using the RS485 to USB interface with 1.8m cable length, or the 5.0m cable. Wireless connection via Zigbee Brand Victron Energy Manufacturer Part Number REL200200100 GTIN 8719076051268 Warranty 5 Years

Read more less

Brand Victron Energy Manufacturer Part Number REC020005010 Dimensions L120 x W65 x D3mm Weight (kg) 0.2 Warranty 5 Years

Read more less

  Brand Victron Energy Manufacturer Part Number SDRPSKC Dimensions L120 x W65mm Weight (kg) 0.2 Warranty 5 Years

Read more less

  Brand Victron Energy Manufacturer Part Number ASS030066300 Cable Length 30m Warranty 5 Years

Read more less

Brand Victron Energy Manufacturer Part Number ASS030064980 Cable Length 3m Warranty 5 Years

Read more less

Brand Victron Energy Manufacturer Part Number ASS030530230 Cable Length 3m Warranty 5 Years

Read more less

Brand Victron Energy Manufacturer Part Number ASS030530250 Cable Length 5m Warranty 5 Years

Read more less

Brand Victron Energy Manufacturer Part Number ASS030720018 Warranty 5 Years Cable Length 1.8m

Read more less

The Argo Battery Isolators feature a low voltage drop thanks to the use of Schottky diodes: at low current the voltage drop is approximately 0,3 V and at the rated output approximately 0,45 V. All models are fitted with a compensation diode that can be used to slightly increase the output voltage of the alternator. This compensates for the voltage drop over the diodes in the isolator.   Please see Victron Energy’s ‘Energy Unlimited’ or ask for specialist advice when installing a diode isolator. Simply inserting the isolator in the cabling between the alternator and the batteries will slightly reduce charge voltage. The result can be that batteries are not charged to the full 100% and age prematurely.   Alternator energize input Some alternators need DC voltage on the B+ output to start charging. Obviously, DC will be present when the alternator is directly connected to a battery. Inserting a Diode or FET splitter will however prevent any return voltage/current from the batteries to the B+, and the alternator will not start. The new ‘AC’ diode isolators feature a special current limited energize input that will power the B+ when the engine run/stop switch is closed. Brand Victron Energy Manufacturer Part Number ARG100301000R Maximum Charge Current (A) 100 Maximum Alternator Current (A) 100 Number Of Batteries 3 Alternator Energize Input Yes Connection M6 Studs Compensation diode & Energize Connection 6.3mm Faston Dimensions H60 x W120 x D115mm Weight (kg) 0.8 Warranty 5 Years

Read more less

In contrast with diode battery isolators, FET isolators have virtually no voltage loss. Voltage drop is less than 0,02 Volt at low current and averages 0,1 Volt at higher currents.   When using ARGO FET Battery Isolators, there is no need to also increase the output voltage of the alternator. Care should taken however to keep cable lengths short and of sufficient cross section.   Example: When a current of 100 A flows through a cable of 50 mm2 cross section (AWG 0) and 10 m length (30 ft), the voltage drop over the cable will be 0,26 Volt. Similarly a current of 50 A through a cable of 10 mm2 cross section (AWG 7) and 5 m length (15 ft) will result in a voltage drop of 0,35 Volt!   Alternator energize input  Some alternators need DC voltage on the B+ output to start charging. Obviously, DC will be present when the alternator is directly connected to a battery. Inserting a Diode or FET splitter will however prevent any return voltage/current from the batteries to the B+, and the alternator will not start. The new Argofet isolators have a special current limited energize input that will power the B+ when the engine run/stop switch is closed. Brand Victron Energy Manufacturer Part Number ARG100201020R GTIN 8719076019022 Maximum charge current 100A Maximum alternator current 100A Number Of Batteries 2 Connection M8 Bolts Dimensions H65 x W120 x D200mm Weight 1.4Kg Warranty 5 Years

Read more less

In contrast with diode battery isolators, FET isolators have virtually no voltage loss. Voltage drop is less than 0,02 Volt at low current and averages 0,1 Volt at higher currents.   When using ARGO FET Battery Isolators, there is no need to also increase the output voltage of the alternator. Care should taken however to keep cable lengths short and of sufficient cross section.   Example: When a current of 100 A flows through a cable of 50 mm2 cross section (AWG 0) and 10 m length (30 ft), the voltage drop over the cable will be 0,26 Volt. Similarly a current of 50 A through a cable of 10 mm2 cross section (AWG 7) and 5 m length (15 ft) will result in a voltage drop of 0,35 Volt!   Alternator energize input Some alternators need DC voltage on the B+ output to start charging. Obviously, DC will be present when the alternator is directly connected to a battery. Inserting a Diode or FET splitter will however prevent any return voltage/current from the batteries to the B+, and the alternator will not start. The new Argofet isolators have a special current limited energize input that will power the B+ when the engine run/stop switch is closed. Brand Victron Energy Manufacturer Part Number ARG200201020R Maximum Charge Current (A) 200 Maximum Alternator Current (A) 200 Number Of Batteries 2 Connection M8 Bolts Dimensions H65 x W120 x D200mm Weight (kg) 1.4 Warranty 5 Years

Read more less

  Brand Victron Energy Manufacturer Part Number BPC900100014 Warranty 5 Years

Read more less

Features Two AC Outputs The main output has no break functionality. The MultiPlus takes over the supply to the connected loads in the event of a grid failure or when shore/generator power is disconnected. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption. The second output is live only when AC is available on the input of the MultiPlus. Loads that should not discharge the battery, like a water heater for example can be connected to this output (second output available on models rated at 3 kVA and more).   Virtually unlimited power thanks to parallel operation Up to 6 Multis can operate in parallel to achieve higher power output. Six 24/5000/120 units, for example, will provide 25 kW / 30 kVA output power with 720 Amps charging capacity. Three phase capability In addition to parallel connection, three units of the same model can be configured for three phase output. But that’s not all: up to 6 sets of three units can be parallel connected for a huge 75 kW / 90 kVA inverter and more than 2000 Amps charging capacity.   PowerControl – Dealing with limited generator, shore side or grid power The MultiPlus is a very powerful battery charger. It will therefore draw a lot of current from the generator or shore side supply (nearly 10 A per 5 kVA Multi at 230 VAC). With the Multi Control Panel a maximum generator or shore current can be set. The MultiPlus will then take account of other AC loads and use whatever is extra for charging, thus preventing the generator or shore supply from being overloaded.   PowerAssist – Boosting the capacity of shore or generator power This feature takes the principle of PowerControl to a further dimension. It allows the MultiPlus to supplement the capacity of the alternative source. Where peak power is so often required only for a limited period, the MultiPlus will make sure that insufficient shore or generator power is immediately compensated for by power from the battery. When the load reduces, the spare power is used to recharge the battery.   Solar energy: AC power available even during a grid failure The MultiPlus can be used in off grid as well as grid connected PV and other alternative energy systems. Loss of mains detection software is available.   System configuring In case of a stand-alone application, if settings have to be changed, this can be done in a matter of minutes with a DIP switch setting procedure. Parallel and three phase applications can be configured with VE.Bus Quick Configure and VE.Bus System Configurator software.   Brand Victron Energy Manufacturer Part Number PMP122200000 GTIN 8719076052135 Voltage 12V Cont. Output Power at 25°C 2000VA Peak Power 3500W Output AC Voltage 230V Transfer Switch 35A Charge Current House Battery 80A Charge Current Starter Battery 1A Protection Category IP21 Efficiency 93% Bluetooth Compatible No Dimensions H506 x W236 x D147mm Weight 15.5Kg Warranty 5 Years

Read more less

Features A MultiPlus, plus ESS (Energy Storage System) functionality The MultiPlus-II is a multifunctional inverter/charger with all the features of the MultiPlus, plus an external current sensor option which extends the PowerControl and PowerAssist function to 50A resp. 100A. The MultiPlus-II is ideally suited for professional marine, yachting, vehicle and land based off-grid applications. It also has built-in anti-islanding functionality, and an increasingly long list of country approvals for ESS application. Several system configurations are possible. For more detailed information see the ESS Design and configuration manual.   PowerControl and PowerAssist – Boosting the capacity of the grid or a generator A maximum grid or generator current can be set. The MultiPlus-II will then take account of other AC loads and use whatever is extra for battery charging, thus preventing the generator or grid from being overloaded (PowerControl function). PowerAssist takes the principle of PowerControl to a further dimension. Where peak power is so often required only for a limited period, the MultiPlus-II will compensate insufficient generator, shore or grid power with power from the battery. When the load reduces, the spare power is used to recharge the battery.   Solar energy: AC power available even during a grid failure The MultiPlus-II can be used in off grid as well as grid connected PV and other alternative energy systems. It is compatible with both solar charger controllers and grid-tie inverters.   Two AC Outputs The main output has no break functionality. The MultiPlus-II takes over the supply to the connected loads in the event of a grid failure or when shore/generator power is disconnected. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption. The second output is live only when AC is available on the input of the MultiPlus-II. Loads that should not discharge the battery, like a water heater for example, can be connected to this output.   Virtually unlimited power thanks to parallel and three phase operation (not available for the 8k and 10k models) Up to 6 Multis can operate in parallel to achieve higher power output. Six 48/5000/70 units, for example, will provide 25 kW / 30 kVA output power with 420 Amps charging capacity. In addition to parallel connection, three units of the same model can be configured for three phase output. But that’s not all: up to 6 sets of three units can be parallel connected for a 75 kW / 90 kVA inverter and more than 1200 Amps charging capacity.   On-site system configuring, monitoring and control Settings can be changed in a matter of minutes with VEConfigure software (computer or laptop and MK3-USB interface needed). Several monitoring and control options are available: Cerbo GX, Color Control GX, Venus GX, Octo GX, CANvu GX, laptop, computer, Bluetooth (with the optional VE.Bus Smart dongle), Battery Monitor, Digital Multi Control Panel.   Remote configuring and monitoring Install a Cerbo GX or other GX product to connect to the internet. Operational data can be stored and displayed on our VRM (Victron Remote Management) website, free of charge. When connected to the internet, systems can be accessed remotely, and settings can be changed. Brand Victron Energy Manufacturer Part Number PMP122305010 GTIN 8719076048916 Voltage 12V Cont. Output Power at 25°C 3000VA Peak Power 5500W Output AC Voltage 230V Transfer Switch 32A Max. AC Input Current 32A Max. Battery Charge Current 120A Protection Category IP22 Efficiency 93% Bluetooth Compatible Yes Dimensions H546 x W275 x D147mm Weight 19Kg Warranty 5 Years  

Read more less

The sturdy 6mm stainless bracket is fixed through one slate to the rafter beneath. The slate above is replaced above the fixings, so that the roof remains weathertight. Where the bracket is close to the edge of the covering slate, we suggest using a lead soaker over the bracket to ensure the roof remains watertight. System features and specifications: Suitable for pitched and flat roofs Cladding type: slate (other roof mounts also available) Maximum slope: 60 degrees Wind load: up to 60m/s Snow load: 2.0kn/m2 Maximum building height: 20m Material: stainless steel Color: silver MCS 012 certification Warranty: 12 years durability on material, 5 years on finish Manufacturer: Xiamen Fasten Solar Technology Co., Ltd

Read more less

Part No: RR-W2-12-G Storage Systems - Battery Cabinet Battery Cabinet 12U Part Code RR-W2-12-G   This cabinet is suitable for housing of up to: 5 x Pylontech US2000B Plus Lithium-Ion batteries or 3x Pylontech US3000  Lithium-Ion batteries or 3x Fox ESS HV2600 Lithium-Ion batteries Dimensions assembled - W 550mm X D 550 mm X H 615mm. Each cabinet comprises a welded steel frame and adjustable front and rear mounting profiles. The cabinets feature ventilation slots in the top, have a lockable glass front door, and removable sides. The cabinet is finished in a high quality attractive black.   Batteries need to be attached using front battery mounting holes only. Ready assembled Supplier Part No: RR-W2-12-G Weight: 22.5 kg    

Read more less

This part is a special offer made up of the following items: Part   1 x FE-HV-ECM-4100 Fox ECS 4.03kWh HV Battery (Master)   1 x FE-HV-ECS-4100 Fox ECS 4.03kWh HV Battery (Slave)   1 x FE-H1-3.7-G2 Fox H1 3.7kW Hybrid Inverter 1PH G2 Weight: 95.05 kg

Read more less

Part No: FE-T-10.0 Inverters - Main Units Rating: 10,000W Phases: 3 FOX ESS - PV Inverter - T Series - 10.0kW T10-G3   Don't forget: You must register your install with Fox online to activate the 10 year product warranty, otherwise it's 5 years as standard. Supplier Part No: T10 Weight: 17 kg Rated Power: 10,000 W Min PPT Voltage: 140 V Max PPT Voltage: 1,100 V DC Startup Voltage: 140 V DC Shutdown Voltage: 1,100 V Max Input Voltage: 1,100 V Max DC Power: 15,000 W Max AC Power (5 Minutes): 10,000 W Surge AC Power (1 Second): 11,000 W Max DC Current: 14 A Max DC Inputs: 2 Has DC Fuses: 2 Connector: MC4   Included Connectors: 2 Euro Efficiency: 97.8 % Transformer: N/A MPPT Quantity : 2 Has Integrated DC Switch: Yes Warranty: 5 years

Read more less

Part No: FE-S2000 Inverters - Main Units Rating: 2,000W Phases: 1 FOX ESS - PV Inverter - S Series - 2.0kW S2000-G2 Don't forget: You must register your install with Fox online to activate the 10 year product warranty, otherwise it's 5 years as standard. Supplier Part No: S2000 Weight: 5.4 kg Rated Power: 2,000 W Min PPT Voltage: 60 V Max PPT Voltage: 500 V DC Startup Voltage: 60 V DC Shutdown Voltage: 500 V Max Input Voltage: 500 V Max DC Power: 3,000 W Max AC Power (5 Minutes): 2,000 W Surge AC Power (1 Second): 2,200 W Max DC Current: 14 A Max DC Inputs: 1 Has DC Fuses: 1 Connector: MC4   Included Connectors: 1 Euro Efficiency: 96.8 % Transformer: N/A MPPT Quantity : 1 Has Integrated DC Switch: Yes Warranty: 5 years

Read more less

Part No: FE-H3-12.0 Storage Systems - Hybrid Inverter Weight: 28 kg Rated Power: 12,000 W Min PPT Voltage: 160 V Max PPT Voltage: 950 V DC Startup Voltage: 160 V DC Shutdown Voltage: 160 V Max Input Voltage: 1,000 V Max DC Power: 15,000 W Max AC Power (5 Minutes): 12,000 W Surge AC Power (1 Second): 13,200 W Max DC Current: 26 A Max DC Inputs: 3 Has DC Fuses: 0 Connector: MC4   Included Connectors: 4 Euro Efficiency: 98 % Transformer: N/A MPPT Quantity : 2 Has Integrated DC Switch: Yes

Read more less

CODE R-B12100C MPN (MANUFACTURER PART NUMBER) R-B12100C BRAND Topband TOPBAND battery provides advanced Lead acid drop-in replacement battery solution, widely used in RV, fishing boats, cleaning machines, golf carts, solar energy storage systems and other fields. Topband battery makes our products available through the best knowledge-based distribution and service organizations for the people and businesses who rely on batteries to work, live, or get away. Topband battery provides advanced LiFePO4 batteries for lead acid drop-in battery solution, light and compact drop-in replacement Features Standard lead acid cases, customized case Bluetooth app monitoring Heating function optional 4000+cycles，80%DOD UN38.3/CE certified Support series or parallel connection Nominal Voltage 12.8V Battery Capacity 100Ah Terminal Type M8 Dimensions L354 x W175 x H190mm Weight 12.5Kg Warranty 5 Years Battery Technology Lithium Battery Application Deep Cycle Max. Charge Current 150Ah

Read more less

CODE TN-LFP12.8V24Ah MPN (MANUFACTURER PART NUMBER) TN24 Features Using the technology of lithium iron phosphate cell, superior safety, thousands of cycles, 100%DOD, under normal conditions Built-in automatic protection for over-charge, over discharge, over current and over temperature Free of maintenance Internal cell balancing Lighter weight: About 40% -50% of the weight of a comparable lead acid battery Can be charged using most standard lead-acid charges (set) Wider temperature range:-20°C-60°C Support for Series application expansion (up to 51.2V) and two in parallel Applications UPS Solar &Wind Power System Golf Cart Electric Vehicle , E-bike, E-rickshaw etc. Lighting   Voltage 12V Battery Capacity (C20) 24Ah Terminal Type M5 Terminal Layout Right Hand Positive Dimensions (Including Terminals) L181 x W77 x H167mm Weight 2.9Kg Country of Manufacture China Battery Technology Lithium Battery Application Deep Cycle

Read more less

Part No: EN-Q-SEAL Inverters - Inverter Accessories Q cable sealing caps (female)  One needed to cover each unused connector on the cabling.  Single item only.   Supplier Part No: Q-SEAL-10 Weight: 0.02 kg

Read more less