Quick Order

Cyrix Battery Combiners are an excellent replacement for diode isolators. The main feature is that there is virtually no voltage loss so that the output voltage of alternators or battery chargers does not need to be increased. Features Intelligent battery monitoring to prevent unwanted switching Some battery combiners (also called voltage controlled relay, or split charge relay) will disconnect a battery in case of a short but high amperage load. A battery combiner also may fail to connect a large but discharged battery bank because the DC voltage immediately drops below the disengage value once the batteries are connected. The software of the Cyrix-ct 12/24 does more than simply connect and disconnect based on battery voltage and with a fixed time delay. The Cyrix-ct 12/24 looks at the general trend (voltage increasing or decreasing) and reverses a previous action only if the trend has reversed during a certain period of time. The time delay depends on the voltage deviation from the trend. (for Battery Combiners with multiple engage/disengage profiles, please see the Cyrix-i 400) Protection against overheating (due to a long duration overload e.g.) The Cyrix will disengage in case of excessive contact temperature, and reengage again after it has cooled down. 12/24 V auto ranging The Cyrix-ct 12/24 automatically detects system voltage. No voltage loss Cyrix battery combiners are an excellent replacement for diode isolators. The main feature is that there is virtually no voltage loss so that the output voltage of alternators or battery chargers does not need to be increased. Prioritising the starter battery In a typical setup the alternator is directly connected to the starter battery. The accessory battery, and possibly also a bow thruster and other batteries are each connected to the starter battery with Cyrix battery combiners. When a Cyrix senses that the starter battery has reached the connect voltage it will engage, to allow for parallel charging of the other batteries. Bidirectional voltage sensing and power supply from both batteries The Cyrix senses the voltage of both connected batteries. It will therefore also engage if for example the accessory battery is being charged by a battery charger. The Cyrix-ct 12/24 has a dual power supply. It will therefore also close if the voltage on one battery is too low to operate the Cyrix. In order to prevent unexpected operation during installation or when one battery has been disconnected, the Cyrix-ct 12/24 will not close if the voltage on one of the two battery connections is lower than 2 V (12 V battery) or 4 V (24 V battery). Parallel connection in case of emergency (Start Assist) The Cyrix can also be engaged with a push button (Cyrix remains engaged during 30 seconds) or a switch to connect batteries in parallel manually. This is especially useful in case of emergency when the starter battery is discharged or damaged. Protection Category IP54 Country of Manufacture Malaysia Manufacturer Part Number CYR010120011R Weight (kg) 0.11 Dimensions H46 x W46 x D80mm Brand Victron Energy Control Cable Included (Length 1 m) No LED Status Indication No Start Assist Yes (Cyrix remains engaged during 30 seconds) Cranking Rating (5 seconds) 180A Voltage 12/24 Warranty 5 Years

Read more less

Requires one of these BMS-es: VE.Bus BMS – recommended for systems with our inverter/chargers. smallBMS – recommended for use in small systems. Battery Management System BMS 12/200 – recommended for use in Automotive and Marine systems having DC-loads and Alternators. Smart BMS 12/ 200– recommended for use in Automotive and Marine systems having DC-loads and Alternators. Smart BMS CL 12/100 – recommended for use in Automotive and Marine systems having DC-loads and Alternators. Lynx smart BMS – recommended for use in large systems.  Features of the 160Ah Smart Battery RuggedA lead-acid battery will fail prematurely due to sulfation:• If it operates in deficit mode during long periods of time (i.e. if the battery is rarely, or never at all, fully charged).• If it is left partially charged or worse, fully discharged (yacht or mobile home during wintertime).A LFP battery does not need to be fully charged. Service life even slightly improves in case of partial charge instead of a full charge. This is a major advantage of LFP compared to lead-acid.Other advantages are the wide operating temperature range, excellent cycling performance, low internal resistance and high efficiency (see below). LFP is therefore the chemistry of choice for demanding applications.   EfficientIn several applications (especially off-grid solar and/or wind), energy efficiency can be of crucial importance.The round-trip energy efficiency (discharge from 100% to 0% and back to 100% charged) of the average lead acid battery is 80%.The round-trip energy efficiency of a LFP battery is 92%.The charge process of lead-acid batteries becomes particularly inefficient when the 80% state of charge has been reached, resulting in efficiencies of 50% or even less in solar systems where several days of reserve energy is required (battery operating in 70% to 100% charged state).In contrast, a LFP battery will still achieve 90% efficiency under shallow discharge conditions.   Size and weightSaves up to 70% in spaceSaves up to 70% in weight   Expensive?LFP batteries are expensive when compared to lead-acid. But in demanding applications, the high initial cost will be more than compensated by longer service life, superior reliability and excellent efficiency.   BluetoothWith Bluetooth cell voltages, temperature and alarm status can be monitored.Very useful to localize a (potential) problem, such as cell imbalance.   The 160Ah Smart battery is equipped with Bluetooth and uses this to communicate with the VictronConnect app. The VictronConnect app can be used for:• Monitoring the battery status• Monitoring the battery voltage• Monitoring the battery temperature• To find out when the battery was last fully charged• Monitoring the cell balancing status• Monitoring the individual cell voltages• To view or change the battery settings• To update the battery firmware   Brand Victron Energy Manufacturer Part Number BAT512118610 gtin 8719076060260 Battery Capacity (C20) 180Ah Terminal Type M10 Terminal Layout Right Hand Positive Dimensions (Including Terminals) H237 x W321 x D152mm Weight 20.5Kg Warranty 3 Years Country of Manufacture China Battery Technology Lithium Battery Application Deep Cycle WooCategory1 Batteries By Application WooCategory2 Batteries By Application Leisure & Marine WooCategory3 Leisure & Marine WooCategory4 Batteries By Application Leisure & Marine Victron Energy WooCategory5 Batteries By Application Horsebox WooCategory13 Batteries WooCategory7 Victron Energy WooCategory18 Brands Victron Energy Batteries WooCategory17 Victron Energy WooCategory16 Brands Victron Energy WooCategory6 Batteries By Application Horsebox Hankook WooCategory14 Product Type Batteries Leisure WooCategory15 Brands WooCategory12 Product Type Batteries WooCategory11 Product Type WooCategory10 Lithium Smart WooCategory9 Lithium Smart Batteries WooCategory8 Victron Energy Batteries Voltage (V) 12.8V

Read more less

The SmartShunt is a good alternative for a BMV battery monitor, especially for systems where battery monitoring is needed but less wiring and clutter is wanted.The SmartShunt is equipped with Bluetooth, a VE.Direct port and a connection that can be used for: monitoring a second battery, midpoint monitoring or a temperature sensor. Differences compared to BMV-712 Battery Monitor– No programmable visual and audible alarm– No programmable relay Why should I monitor my battery with the SmartShunt IP65 1000A?Batteries are used in a wide variety of applications, mostly to store energy for later use. But how much energy is stored in the battery? No one can tell by just looking at it. The service life of batteries depends on many factors. Battery life may be shortened by under-charging, over-charging, excessively deep discharges, excessive charge or discharge currents, and by high ambient temperature. Monitoring the battery with a battery monitor will give important feedback to the user so that remedial measures can be taken when necessary. Doing this will extend battery life and the battery monitor will quickly pay for itself.   Brand Victron Energy Manufacturer Part Number SHU065210050 gtin 8719076057901 Protection Category IP65 Bluetooth Enabled Yes Dimensions H68 x W168 x D75mm Country of Manufacture India Warranty 5 Years

Read more less

The SmartShunt is a good alternative for a BMV battery monitor, especially for systems where battery monitoring is needed but less wiring and clutter is wanted.The SmartShunt is equipped with Bluetooth, a VE.Direct port and a connection that can be used for: monitoring a second battery, midpoint monitoring or a temperature sensor. Differences compared to BMV-712 Battery Monitor– No programmable visual and audible alarm– No programmable relay Why should I monitor my battery with the SmartShunt IP65 2000A?Batteries are used in a wide variety of applications, mostly to store energy for later use. But how much energy is stored in the battery? No one can tell by just looking at it. The service life of batteries depends on many factors. Battery life may be shortened by under-charging, over-charging, excessively deep discharges, excessive charge or discharge currents, and by high ambient temperature. Monitoring the battery with a battery monitor will give important feedback to the user so that remedial measures can be taken when necessary. Doing this will extend battery life and the battery monitor will quickly pay for itself.   Brand Victron Energy Manufacturer Part Number SHU065220050 gtin 8719076057918 Protection Category IP65 Bluetooth Enabled Yes Dimensions H68 x W168 x D100mm Warranty 5 Years Country of Manufacture India

Read more less

  Brand Victron Energy Manufacturer Part Number ADA500180100 gtin 8719076054511 Dimensions L105 x W12.5 x D11mm Weight 0.2Kg Warranty 5 Years Country of Manufacture India

Read more less

Modular solar home system The SHS 200 is compatible with different size of batteries (up to 12V/160Ah) and solar panels (up to 200Wp). End-users can progressively increase their power subscription according to their needs and budget. With eleven DC load outputs, the SHS 200 can be connected to a variety of household appliances such LED lighting, phone charging, fans, TVs and a fridge. This solution is also powerful enough for entrepreneurial customers to run a small business. PAYGo ready The SHS 200 is primarily designed for Pay-as-you-go (PAYGo) operations. It is compatible with various PAYGo software platforms and includes a keypad for offline activation. How does it work? PAYGo operators usually offer solar home systems to their customers through a rent-to-own plan on prepayments. Customers can get a SHS 200 against a deposit. Then they make regular payments by mobile money over few months or years to finally own the unit. A recharge code is sent to their cell phone by SMS after each payment. The SHS 200 becomes active only when the code is pressed on its keypad. PAYGo operators can achieve profitability while off-grid populations afford reliable and clean energy. MPPT charger and smart battery management By using Maximum Power Point Tracking (MPPT) technology, the SHS 200 ensures that every drop of available power is rinsed out of the panels and harvested for storage. Additionally smart multi-stage charging and load disconnect features maintain the health and extends the life of the battery. The SHS 200 is compatible with lead-acid and lithium battery technologies.   Brand Victron Energy Remote activation Unlock codes sent to end-user via SMS to activate the system Warranty 5 Years Weight 0.39Kg Dimensions H148 x W204 x D67mm Protection Category IP41 Compatible PAYGo platforms PaygOps, Angaza, Paygee Compatible battery technologies Sealed lead-acid, Victron SuperPack (lithium) Temperature compensation Yes (automatic) Manufacturer Part Number SHS121409230 Suitable battery capacity Up to 160Ah Peak efficiency 96% Maximum charge / discharge currents 14A/20A Nominal PV power 50 to 200Wp total (36 cells panels) gtin 8719076050827 Country of Manufacture China

Read more less

Solar Home System 200 MPPT not included   Brand Victron Energy Manufacturer Part Number SHS800300300 gtin 8719076055389 Dimensions L364 x W207 x H310mm Weight 0.4Kg Warranty 5 Years Country of Manufacture India

Read more less

  Brand Victron Energy Manufacturer Part Number VBB125020620 gtin 8719076056386 Max. Current Rating 250A Max. Voltage Rating 70VDC Dimensions H65 x W216 x D86mm Weight 0.25Kg Warranty 5 Years Country of Manufacture Taiwan

Read more less

Features of the Phoenix Smart IP43 Charger 12/30(1+1)  Bluetooth Smart enabled Any Bluetooth enabled smart phone, tablet or other device can be used to monitor, to change settings and to update the charger when new software features become available.   Adaptive 5-stage charge algorithm: bulk – absorption – recondition – float – storage The Phoenix Smart IP43 charger features our well-known ‘adaptive’ battery management system that can be pre-set to suit different types of batteries. The ‘adaptive’ feature will automatically optimise the charge process relative to the way the battery is being used.   The right amount of charge: variable absorption time When only shallow discharges occur (a yacht connected to shore power for example) the absorption time is kept short in order to prevent overcharging of the battery. After a deep discharge the absorption time is automatically increased to make sure that the battery will be fully charged.   Preventing damage due to excessive gassing: the BatterySafe mode If, in order to quickly charge a battery, a high charge current in combination with a high absorption voltage has been chosen, the charger will prevent damage due to excessive gassing by automatically limiting the rate of voltage increase once the gassing voltage has been reached   Less maintenance and aging when the battery is not in use: the Storage Mode The Storage Mode kicks in whenever the battery has not been subjected to discharge during 24 hours. In the Storage Mode float voltage is reduced to 2,2 V/cell (13,2 V for a 12 V battery) to minimise gassing and corrosion of the positive plates. Once a week the voltage is raised back to the absorption level to ‘equalize’ the battery. This feature prevents stratification of the electrolyte and sulphation, a major cause of early battery failure.   Brand Victron Energy Manufacturer Part Number PSC123051095 gtin 8719076053484 Voltage 12V Charge Current 30A Input Voltage 85-265VAC Number of Outputs 1+1 Protection Category Electronic components: IP43, Connection area: IP22 Efficiency 95% Bluetooth Enabled Yes Dimensions H180 x W249 x D116mm Weight 2.7Kg Warranty 5 Years Country of Manufacture Malaysia

Read more less

Part No: FE-HV-EC-6-4.1-24.6 Storage Systems - Li-ion Battery Pack Fox ECS 4.1kWh - Stack of 6 (24.18kWh Useable Storage) Incl. Master ECM4100  4.03kWh Capacity Scalable to 28.21kWh  90% Depth of Discharge Wide Temperature Tolerence Easy Installation CAN/RS485 Communication High Voltage The quick & easy install feature allows for more ECM4100 battery modules to be added post installation. Weight: 218.3kg Dimensions (Width, Hight, Depth): 570mm x 830mm x 380mm Don't forget: You must register your install with Fox online to activate the 10 year product warranty, otherwise it's 5 years as standard. Please click here for registration page. Please check the warranty document for more information. This battery requires a MINIMUM of 2 modules to work (Master + Slave), This battery can have a MAXIMUM of 7 modules in a stack (1x Master + 6x Slaves) Weight: 229.8 kg Battery Type: Lithium Ion Nominal Energy: 24180 Wh Depth of discharge: 90.00 % Voltage: 345 V Continuous Discharge Rate (Normal Use): 17280 W Maximum Discharge Rate (5 Minutes): 17280 W Surge Discharge Rate (15 Seconds): 22464 W Maximum Charge Rate (5 Minutes): 17280 W

Read more less

Part No: FE-HV-EC-5-4.1-20.5 Storage Systems - Li-ion Battery Pack Fox ECS 4.1kWh - Stack of 5 (20.15kWh Useable Storage) Incl. Master ECM4100  4.03kWh Capacity Scalable to 28.21kWh  90% Depth of Discharge Wide Temperature Tolerence Easy Installation CAN/RS485 Communication High Voltage The quick & easy install feature allows for more ECM4100 battery modules to be added post installation. Weight: 182.3kg Dimensions (Width, Hight, Depth): 570mm x 710mm x 380mm Don't forget: You must register your install with Fox online to activate the 10 year product warranty, otherwise it's 5 years as standard. Please click here for registration page. Please check the warranty document for more information. This battery requires a MINIMUM of 2 modules to work (Master + Slave), This battery can have a MAXIMUM of 7 modules in a stack (1x Master + 6x Slaves) Weight: 191.5 kg Battery Type: Lithium Ion Nominal Energy: 20150 Wh Depth of discharge: 90.00 % Voltage: 288 V Continuous Discharge Rate (Normal Use): 14400 W Maximum Discharge Rate (5 Minutes): 14400 W Surge Discharge Rate (15 Seconds): 18720 W Maximum Charge Rate (5 Minutes): 14400 W

Read more less

Soundproof canopy Bunded frame Cummins Engine Deep Sea Control Panel Varta Batteries Battery Charge Included

Read more less

Soundproof canopy Bunded frame Cummins Engine Deep Sea Control Panel Varta Batteries Battery Charge Included

Read more less

Soundproof canopy Bunded frame Cummins Engine Deep Sea Control Panel Varta Batteries Battery Charge Included

Read more less

Soundproof canopy Bunded frame Cummins Engine Deep Sea Control Panel Varta Batteries Battery Charge Included

Read more less

Soundproof canopy Bunded frame Cummins Engine Deep Sea Control Panel Varta Batteries Battery Charge Included

Read more less

Soundproof canopy Bunded frame Cummins Engine Deep Sea Control Panel Varta Batteries Battery Charge Included

Read more less

IP66 Built-in PID recovery for better module performance (optional) AFCI protection, proactively reduces fire risk Globally recognised branded componentry for longer life Power line communication (PLC) (optional) DC side supports "Y" connector Supports aluminium wire access to reduce cost 6 MPPTs, max. efficiency 98.7% > 150% DC/AC ratio Compatible with bifacial modules Night SVG function Intelligent string monitoring, smart I-V curve scan Remote firmware upgrade with simple operation Application        Commercial Promotion       Solis 5G-PRO Manufacturer       Solis Phases        3 Phase Power Rating         kW80 Inverter Type         String Inverter Built in DC        Yes No. of MPPT       6 Built in Communication         Optional Commodity Code         85044086 Dimensions (mm) (H x W x D)1183 x 585 x 363  

Read more less

IP66 Built-in PID recovery for better module performance (optional) AFCI protection, proactively reduces fire risk Globally recognised branded componentry for longer life Power line communication (PLC) (optional) DC side supports "Y" connector Supports aluminium wire access to reduce cost 6/8 MPPTs, max. efficiency 98.7% > 150% DC/AC ratio Compatible with bifacial modules Night SVG function Intelligent string monitoring, smart I-V curve scan Remote firmware upgrade with simple operation Application        Commercial PromotionSolis       5G-PRO Manufacturer         Solis Phases        3 Phase Power Rating          kW80 Inverter Type         String Inverter Built in DC           Yes No. of MPPT         8 Built in Communication           Optional Commodity Code            85044086 Dimensions (mm) (H x W x D)1183 x 585 x 363

Read more less

Part No: MYEN-TAMPERKIT-2.1 EV Charging - Access Control myenergi Retrofit Tamper Kit  For use with units built between May 2022 and November 2022 (Serial Numbers starting with a 2H, excluding those which end -G)   Supplier Part No: TAMPER KIT 2.1 Weight: 0.02 kg

Read more less

Part No: MATT-SP-EVCP-R-W EV Charging - Charge Point Connection Unit Single phase voltage monitoring and protection unit which allows for the connection of 1 x 32A single phase charge point to the existing PME earth facility. The unit incorpoates a unique monitoring device which disconnects all poles, inclusing CPC, in the event of a fault and has a built in double pole Type A RCBO. This device does not require earth rods or measuring electrodes to function BS:7671 18th edition compliant Suitable for 1 x 32A load Built in Type A RCBO Standard 3 year parts warranty Simple wire in wire out connection Standard mild steel IP2X enclosure   Supplier Part No: SP-EVCP-R(W) Weight: 2.5 kg

Read more less

1600 watt Suitcase Generator - The Latest in Suitcase Generator TechnologyThese Units are quickly becoming the market leaders in the leisure industry and when you get yours you will understand why. Main Features Rated power: 1600 Watts (1800 Watts Max) 120 / 230v. Inverter Technology that allows you to power sensitive electronic equipment such as a laptop or flat-screen TV. Noise Output Only 61Db at 7 Metres. Up to 7 Hours run time on full tank. Green, low-carbon power supply of new generation With the powerful loncin 148F engine. High efficiency, magneto, medium-frequency generator of intelligent control on speed. High reliability, frequency inverter technology. Gas cycle technology with two catheters, which is crucial to effect of the separation of oil and gas. PID closed loop speed control system, intelligent control on speed of motor, which can save at least 24% fuel. Specifications Engine model LC148F Engine type Single cylinder,4 stroke, forced cooling ,OHV Power output 2.2Kw/5000rpm Bore×Stroke 48.6mm×43mm (1.9″×1.7″) Displacement 79cc Compression ratio 9:1 Oil capacity 0.35L(0.01gal) Fuel tank capacity 4.2L(1.1gal) Fuel consumption 395g/Kw.h Run Time 7h Rated voltage 230v/120v Voltage regulator system Automatic Voltage Regulation Rated output 1.6Kw Max output 1.8Kw Power factor 1.0 Charging voltage 12V(DC) Charging current 8.3A(DC) Starting system Recoil start Ignition system Transistorized magneto ignition Noise (7m) 61dB(A) Dimensions 499×285×455(19.6″×11.2″×17.9″) Net weight 21Kg(46lb)   Delivered Free within mainland UK complete with 12 Month Warranty

Read more less

Weight: 286.5 kg Battery Type: Lithium Ion Nominal Energy: 23200 Wh Depth of discharge: 90.00 % Voltage: 460 V Continuous Discharge Rate (Normal Use): 1150 W Maximum Discharge Rate (5 Minutes): 3500 W Surge Discharge Rate (15 Seconds): 16000 W Maximum Charge Rate (5 Minutes): 3500 W

Read more less

LV5200 battery cable accessory kit for use with the LV5200 model. Each battery unit includes the interlink battery solar cables for parallel connection to another battery, whereas this pack is for connecting to the charger. You require one cable pack per system, with a maximum of 4 batteries when used with a 5kW or smaller system, one cable pack is required per battery when used on a larger than 5kW.   This cable pack includes the following solar cables: 1 x 2m long power cable set (positive and negative) with applicable connector 1 x 3m RJ45 Communication cable

Read more less

Part No: PYL-F-H2-BMU-BASE-H7.10 Storage Systems - Li-ion Battery Pack This part is made up of the following items: 2 x PYL-F-H2-BATT-96V Force-H2 Lithium 3.55kWh battery FH9637 module 96V 37AH   1 x PYL-F-H2-BMU-BASE Force H2 BMS with basement and cables (FC0500M)     Benefits Of The Force-H2 System Modular design enables quick and secure installation with no exposed wiring and connectors Stylish design suits both indoor and outdoor installation (with appropriate protection) Proven BMS with wide inverter compatibility Important MAX DISCHARGE RATE IS ONLY APPLICABLE FOR +- 60 SECONDS Weight:83.5 kg

Read more less

IP66 > 150% DC/AC ratio String current up to 16A Supports RS485, WiFi, GPRS Supports export power control Intelligent redundant fan-cooling Natural convection, Fan-less design Wide voltage range and low startup voltage Supports aluminium wire access to reduce cost AFCI protection, proactively reduces fire risk Intelligent string monitoring, smart I-V curve scan Natural convection, Fan-less design, longer lifespan Globally recognised branded componentry for longer life Supports high power modules for lower installation costs 3/4 MPPT design, supports multiple orientation system design Night time PID recovery function, increases overall system yield (optional) Scan to register on SolisCloud, supports remote upgrade and control Supports GPRS/WiFi communication with less wiring and reduced installation costs Application       Commercial Manufacturer       Solis Phases        3 Phase Power Rating          kW36 Inverter Type       String Inverter Built in DC         Yes No. of MPPT      3 Built in Communication           Optional Commodity Code             85044086 Dimensions (mm) (H x W x D)    629 x 647 x 252

Read more less

Part No: X3-MEGA-50K Inverters - Main Units Rating: 50,000W Phases: 3 X3-MEGA-50K Superior Efficiency Max efficiency 98.3%, European efficiency 98.0% 4 independent MPPTs ECO Invention patent technology High Reliability Top-ranking high quality components Integrated type II DC &AC surge arresters Intelligent Maintenance Intelligent monitoring via APP & Web Multiple-string monitoring for easy trouble shooting (Optional) Excellent Grid Compatibility Advanced grid impedance algorithm for large-scale power stations Active power/reactive power control option (Remotely) UK ONLY: Due to a slight change in the regulations relating to G98 and G99, some manufacturers have had to resubmit their type test certificates for reassessment with the ENA. This may lead to some delays in the processing of applications, but we have been reassured by manufacturers they do not anticipate this to delay applications beyond a few weeks. Segen have not been involved in this process and are unable to provide timescales or dates as to when this works will be completed. Due to our current high volume of calls we would kindly ask you to refrain contacting your AM regarding these timescales. Supplier Part No: X3 Mega 50kWWeight: 65 kgRated Power: 50,000 WMin PPT Voltage: 200 VMax PPT Voltage: 960 VDC Startup Voltage: 200 VDC Shutdown Voltage: 250 VMax Input Voltage: 1,000 VMax DC Power: 65,000 WMax AC Power (5 Minutes): 50,000 WSurge AC Power (1 Second): 55,000 WMax DC Current: 130 AMax DC Inputs: 3Has DC Fuses: 0Connector: MC4Included Connectors: 2Euro Efficiency: 98 %Transformer: NoneMPPT Quantity : 2Has Integrated DC Switch: NoWarranty: 5 years Click Here For Specs 

Read more less

Part No: SUN-CABLE-PACK Storage Systems - Accessory Inverter to Battery long cable pack for Sunsynk CATL battery only.  Does not work with Sunsynk BYD battery.  Supplier Part No: Battery Cable Pack Long for Sunsynk Weight: 1 kg

Read more less

SUN-CABLE-SHORT-BYD Storage Systems - AccessoryBattery to Battery short cable pack. Length: 30 cm. Only suitable for batteries next to each other vertically. For horizontal cables need to be sent to Sunsyk UK for them to extend the cables

Read more less

3 UNITS IN STOCK Part No: PYL-L2-BMU-BASE-L10.65 Storage Systems - Li-ion Battery Pack Pylon Force-L2 Low Voltage System 10.65kWh This product package consists of 3x Force-L2 battery modules with 3.55kWh capacity each plus 1x Force-L2 base with BMU. Pylontech's Force-L2 is a home energy storage system (HESS) using a modern, modular design combined with easy installation, simple connectors and outdoor compatibility. Benefits Of The Force-L2 System Modular design enables quick and secure installation with no exposed wiring and connectors LFP technology provides long cell life and high safety Stylish design suits both indoor and outdoor installation (with appropriate protection) Proven BMS with wide inverter compatibility Pylontech Force-L2 is a home energy storage system (HESS) using a modern, modular design combined with easy installation, simple connectors and outdoor compatibility.   Weight: 131.5 kg Battery Type: Lithium Ion Nominal Energy: 10650 Wh Depth of discharge: 90.00 % Voltage: 48 V Continuous Discharge Rate (Normal Use): 4800 W Maximum Discharge Rate (5 Minutes): 4800 W Surge Discharge Rate (15 Seconds): 5040 W Maximum Charge Rate (5 Minutes): 4800 W Data Sheet Force-L1 and Force L-2 data

Read more less

Part No: X1-EPS-UK Storage Systems - Accessory Solax X1-EPS-UK - Emergency Power Supply Box - Backup BOX 100A EPS Box integrates two contactors which provides simple connection for users. It is compatible with X-hybrid E Series inverter. Configured with EPS Box, customers just need to connect several wires between inverter and EPS Box.   Please check if that’s sufficient in the property where you are planning your install. Please only wire essential loads to the EPS circuits. Supplier Part No: EPS Kit Weight: 3 kg Data Sheet X1 BOX EPS

Read more less

This part is made up of the following items: 1 x Fox Energy Cube 4.03kWh HV Battery (Master)   1 x  Fox Energy Cube 4.03kWh HV Battery (Slave)     Fox Energy Cube 4.1kWh - Stack of 2 (8.06kWh) Incl. Master ECM4100  4.03kWh Capacity Scalable to 28.21kWh  90% Depth of Discharge Wide Temperature Tolerence Easy Installation CAN/RS485 Communication High Voltage The quick & easy install feature allows for more ECM4100 battery modules to be added post installation. Dimensions (Width, Hight, Depth): 570mm x 350mm x 380mm This battery stack allows for a MAXIUMUM OF 7 modules in a series and must include 1 Master    Weight: 76.6 kg Battery Type: Lithium Ion Nominal Energy: 8060 Wh Depth of discharge: 90.00 % Voltage 115 V Continuous Discharge Rate (Normal Use): 5760 W Maximum Discharge Rate (5 Minutes): 5760 W Surge Discharge Rate (15 Seconds): 7488 W Maximum Charge Rate (5 Minutes): 5760 W  

Read more less

Part No: X3-HYBRID-G4-10.0-V2 Storage Systems - Hybrid Inverter High-efficient 150% PV oversized and 110% overload output Maximum 150% overload output Higher efficiency on charging and discharging, up to 97.5% Built-in shadow tracking functio Economic Maximum 16A DC input current, support for high power solar panel Store the surplus energy from PV to battery Low start output voltage makes inverter longer working time Less energy loss on battery to inverter Intelligent Switchover time <10ms Quick configuration with U-disk Lithium & Lead-acid battery compatible CT compatible, loads respond within 0.3s Intelligent loads management(e.g., Heat pump) On & Off-grid parallel function, up to 150kW 5 work modes, 2 charging periods available VPP ready, ancillary service in power market Three-phase unbalanced output 50% nominal output power on single phase at most Wi-Fi is now included with Solax X3-Hybrid-G4 V2 product so no need to purchase additional Wi-Fi equipment Supplier Part No: X3-Hybrid G4 10.0 V2 with Wi-Fi & CT Weight: 34 kg Rated Power: 10,000 W Min PPT Voltage: 180 V Max PPT Voltage: 950 V DC Startup Voltage: 180 V DC Shutdown Voltage: 0 V Max Input Voltage: 950 V Max DC Power: 10,000 W Max AC Power (5 Minutes): 10,001 W Surge AC Power (1 Second): 10,002 W Max DC Current: 24 A Max DC Inputs: 2 Has DC Fuses: 0 Connector: SUNCLIX   Included Connectors: 0 Euro Efficiency: 97 % Transformer: HF MPPT Quantity : 0 Has Integrated DC Switch: No Data Sheet X3 G4

Read more less

 Part No: X1-FIT-G4-5.0 Storage Systems - Charger-Inverter X1 RetroFit AC Charger Upgrade a PV system with the X1 RetroFit AC Coupled Inverter Charger from SolaX. Compatible with any brand (single phase) inverter, the X1 retro-fit has a maximum efficiency of up to 97%, is rated for indoor or outdoor use and can be remotely monitored via the XCloud. Additional features: High voltage battery support means thinner cables are required 6kW Max charge/discharge Wifi or LAN stick available separately Suitable for grid trading applications with less than 0.5s response time Charging from grid possible Natural Cooling, quiet and low maintenance Please note the minimum number of Solax batteries per X1 AC inverter is 1 and maximum of 3. Please note batteries need to be the same capacity, its not possible to connect both 4.5kWh and 6.3kWh to one inverter. UK only: This inverter has been tested and certified according to G98 or G99, but only for units having most recent Firmware and Hardware version. All Segen stock meets that criteria. Supplier Part No: X1-FIT-5.0 Charger G4 Weight: 24.5 kg Rated Power: 5,000 W Data Sheet Solax X1 Fit EN

Read more less

Part No: EN-STORAGE-BRACKET Storage Systems - Wall Bracket Wall mounting bracket for the Enphase AC battery modules. One required per battery.  BWM-450MM-A: 450 mm (W) x 311 mm (H) Supplier Part No: BWM-450MM-A Weight: 3.86 kg Enphase Energy, founded in 2006 in California, is the world leader in micro inverter technology with more than 13 million units sold worldwide and over 500,000 installed systems representing over 3GW of clean energy.

Read more less

SUN-CABLE-PACK-BYD Storage Systems - Accessory Inverter to Battery long cable pack. 

Read more less

Battery to Battery short cable pack.  For Sunsynk CATL battery only.  Does not work with Sunsynk BYD battery. 

Read more less

Part No: X1-3000T Storage Systems - Hybrid Inverter X1-Hybrid HV Single Phase The third generation of the X1-Hybrid Storage Inverter is the latest to be released from SolaX and has a range of new features such as built-in EPS output that enables the end user to run off their batteries in the event of a power cut, Export Control making it possible to limit exported power and advanced connectivity making it suitable for grid-trading applications. Other features like easy remote access with monitoring using the SolaX app – Xcloud, makes it very user (and installer) friendly while the industry-leading 10-year warranty gives great peace of mind. Additional features: High voltage battery support means thinner cables are required 6kW Max charge/discharge Wifi or LAN stick available separately G100 Export Limitation compliant Suitable for grid trading applications with less than 0.5s response time Charging from grid possible Please note the minimum number of batteries per X1 Hybrid inverter is 1 and maximum of 3. Please note batteries need to be the same capacity, its not possible to connect both 4.5kWh and 6.3kWh to one inverter. UK only: This inverter has been tested and certified according to G98 or G99, but only for units having most recent Firmware and Hardware version. All Segen stock meets that criteria.   Supplier Part No: X1-Hybrid 3000E Weight: 26.9 kg Rated Power: 3,000 W Min PPT Voltage: 125 V Max PPT Voltage: 550 V DC Startup Voltage: 125 V DC Shutdown Voltage: 125 V Max Input Voltage: 600 V Max DC Power: 4,500 W Max AC Power (5 Minutes): 3,300 W Surge AC Power (1 Second): 6,000 W Max DC Current: 24 A Max DC Inputs: 2 Has DC Fuses: 0 Connector: SUNCLIX   Included Connectors: 2 Euro Efficiency: 97 % Transformer: None MPPT Quantity : 2 Has Integrated DC Switch: No Warranty: 10 years Data Sheet Solax X1 G3 Hybrid 2021

Read more less

The Fox system is easy to install and will save you time spent on installation. Remote monitoring is also avalible via your smartphone or web portal. Uses high voltage batteries  IP65 rated - suitable for outdoor installations Remote monitoring via web portal or smartphone Easy to expand battery capacity Dual MPPT - ensure optimal solar production High round-trip efficiency of 97% CT Clamps, meter and WiFi stick are included in the box Please Note: When installing batteries side-by-side and not stacked one on top of the other, we recommend using    Weight: 26.7 kg Rated Power: 3,000 W Min PPT Voltage: 80 V Max PPT Voltage: 550 V DC Startup Voltage: 75 V DC Shutdown Voltage: 75 V Max Input Voltage: 600 V Max DC Power: 4,680 W Max AC Power (5 Minutes): 5,000 W Surge AC Power (1 Second): 6,000 W Max DC Current: 27 A Max DC Inputs: 2 Has DC Fuses: 0 Connector: MC4   Included Connectors: 4 Euro Efficiency: 97 % Transformer: None MPPT Quantity : 2 Has Integrated DC Switch: Yes Warranty: 5 years

Read more less

Part No: X3-HYBRID-G4-15.0-V2 Storage Systems - Hybrid Inverter SolaX's X-Hybrid three-phase inverter is the most updated version of their hybrid inverters range. This adaptable and expandable device caters to residential and commercial purposes, with the possibility to incorporate several inverters in parallel allowing for scalable battery storage used in commercial settings. The inverter also comes with a feature called EPS (Emergency Power Supply), which utilizes extra changeover devices. Multiple communication options are available, and the device can be controlled remotely. Some of its significant features are maximum efficiency of 98%, dual MPTT, remote monitoring, an IP65 rating, and a 10-year warranty. Key features: In-built EPS changeover switch Supports up to 150% over-sizing 30A Charge/discharge capability On-grid and off-grid use Includes WiFi dongle Looking to expand your system capacity? See Solax EPS Parallel Box options  – Connect up 6 hybrid inverters with a maximum of 60kW – Connect up 10 hybrid inverters with a maximum of 150kW Wi-Fi is now included with Solax X3-Hybrid-G4 V2 product so no need to purchase additional Wi-Fi equipment Supplier Part No: X3-Hybrid 15.0-D G4 V2 with WiFi Weight: 30 kg Rated Power: 15,000 W Min PPT Voltage: 180 V Max PPT Voltage: 950 V DC Startup Voltage: 200 V DC Shutdown Voltage: 200 V Max Input Voltage: 950 V Max DC Power: 18,000 W Max AC Power (5 Minutes): 15,001 W Surge AC Power (1 Second): 15,002 W Max DC Current: 26 A Max DC Inputs: 2 Has DC Fuses: 0 Connector: SUNCLIX   Included Connectors: 2 Euro Efficiency: 97 % Transformer: None MPPT Quantity : 2 Has Integrated DC Switch: No Warranty: 5 years

Read more less

  HIGH STOCK AVAILABLE Included in kit: 1 x US5000 Battery 1 x Solis 3.6kw hybrid inverter 1 x Pylon cable pack 1 x Solis data stick 1 x Keto fuse holder with 2 x 80a fuses   The Pylontech US2000C has an incredible DoD of 95%  Supplier Part No:PYLON-US2000C Weight:24 kg Battery Type:Lithium Ion Nominal Energy:2400 Wh Depth of discharge:95.00 % Voltage:48 V Continuous Discharge Rate (Normal Use):1200 W Maximum Discharge Rate (5 Minutes):2400 W Surge Discharge Rate (15 Seconds):4320 W Maximum Charge Rate (5 Minutes):2400 W Data Sheet US2000C, US3000C and US5000      

Read more less

  STOCK AVAILABLE, PLEASE INQUIRE ON OUR LIVE CHAT FOR IMMEDIATE RESPONSE Included in kit: 2 x Pylontech US3000C 3.5kWh batteries 2 x US3000 battery brackets 1 x Solis 3.6kw hybrid inverter 1 x Pylon cable pack 1 x Solis data stick 1 x Keto fuse holder with 2 x 80a fuses   Pylon US3000C LiFePo4 Battery 3.5kWh for Solar   Supplier Part No: PYLON-US3000C Weight: 32 kg Battery Type: Lithium Ion Nominal Energy: 3552 Wh Depth of discharge: 95.00 % Voltage: 48 V Continuous Discharge Rate (Normal Use): 1776 W Maximum Discharge Rate (5 Minutes): 3552 W Surge Discharge Rate (15 Seconds): 4320 W Maximum Charge Rate (5 Minutes): 1776 W Data Sheet US2000C, US3000C and US5000      

Read more less

Download Spec Sheet HERE https://cdn.shopify.com/s/files/1/0619/6428/8220/files/GGW50G-2023-10-13-09-12-10.pdf?v=1697410189 PRAMAC Industrial gaseous engine-driven generator, model GGW50G, consisting of the following features and accessories: Stationary Emergency-Standby ESP rating (ISO-8528-1) 50 kVA / 40 kW Rating, wired for 231 / 400 VAC Three phase, 50 Hz. Prime Power rating (ISO-8528-1) 45 kVA / 36 kW Rating, wired for 231 / 400 VAC Three phase, 50 Hz. Mecc-Alte alternator Auxiliary Winding Excitation Generac engine model G4.5 Naturally Aspirated 4 cylinder. 4.5L Displacement Dual gas shutoff solenoid actuated valves Electronic Air/Fuel regulation Sound-Attenuated Acoustic Enclosure, Steel Self supporting inner structure Galvanized sheet metal robust construction Lifting points from the top Green PRAMAC Baked-On Powder Coat Finish Power Zone Pro Digital Control Panel for Single Generators Meets NFPA 99 and 110 requirements Temp Range -40 to 70 degrees C Humidity 2 – 95% (Non Condensing) UL6200 C-ETL-US CE FCC IEC801 (Radiated Emissions, Susceptibility, and Surge Immunity) 4.3” Resistive Color Touchscreen Built-in Wi-Fi, Bluetooth, and Webserver (via Power Zone Connectivity Server) IP65 (front) Auto/Manual/Off key switch, Alarm Indication, Not in Auto Indication, audible alarm, emergency stop switch Dual Core Digital Microprocessor RS485, Ethernet and CANbus ports All engine sensors are 4-20ma for minimal interference Sensors: Oil Pressure, optional Oil Temp, Coolant Temp and Level, Fuel Level/Pressure (where applicable), Engine Speed, DC Battery Voltage, Run-time Hours, Generator Voltages, Amps, Frequency, Power, Power Factor Alarm Status: Low or High AC Voltage, Low or High Battery Voltage, Low or High Frequency, Pre-low or Low Oil Pressure, Pre-high or High Oil Temp (optional), Low Water Level and Temp, Pre-high or High Engine Temp, High, Low, and Critical-low Fuel Level/Pressure (where applicable), Overcrank, Over and Under Speed, Unit Not in Automatic Programmable I/O Built-in PLC for special applications Engine function monitoring and control: Full range standby operation; programmable auto crank, Emergency Stop, Auto-Off-Manual switch Isochronous Governor 0.25% digital frequency regulation with: soft-start ramping - adjustable, gain - adjustable, overshoot limit - adjustable 3 Phase RMS Voltage Sensing +/-0.5% digital voltage regulation with: soft-start voltage ramping - adjustable, loss of sensing protection - adjustable, negative power limit - adjustable, Hi/Lo voltage limit - adjustable, V/F slope and gain - adjustable, fault protection Service reminders, trending, fault history (alarm log) I2T function for full generator protection Selectable low-speed exercise 2-wire start controls for any 2-wire transfer switch 3 Owner's Manuals 2 Years Standard Warranty or 1000 running hours whichever comes sooner. 4 pole circuit breakers. Coolant Heater, 1500W, 240VAC Exhaust system with 3-way catalyst optimized for ultra-low emissions (NOx < 250 mg /Nm3 @5%O2)  

Read more less

Part No: KG20-T204-GBA486 Switches - AC Isolators Kraus & Naimer AC Switch Suitable for three phase AC connection. Plastic Enclosures, Protection IP66, totally insulated, knock-outs Handle red, in the OFF-position lockable with padlocks, Plate Backing grey Dimensions (w x h x d): 100mm x 190mm X 93mm Switch interlocked with lid to prevent opening in ‘ON’ position Keywords: 17kW, KG20T204GBA486, Kraus & Naimer, Switches, AC Isolator Supplier Part No: KG20 T204/GBA486 KL51V Weight: 0.48 kg Rated Power: 17,320 W Poles: 4 Max Cable: 10 mm2 Max Voltage: 690 V Rated Current: 25 A Rated Voltage: 400 V Established in 1907 in Austria, Kraus & Naimer has grown to be one of world's highest quality and largest switch manufacturer in the world. For over 100 years Kraus & Naimer have been manufacturing top quality electrical switches and now offer the widest range of solar photovoltaic AC and DC isolators on the market. Every solar PV system requires at least one DC disconnector to isolate the PV array from the input to the inverter and at least one AC disconnector to isolate the inverter from the mains supply. Choosing a well proven and high quality product for these small but vital parts of any PV system is essential and there is no safer choice than Kraus & Naimer.

Read more less

Part No: KG20-T104GB Switches - DC Isolators Kraus & Naimer DC Switch Switch - Disconnectors, 4 pole - for 2 strings             IP66/67 Protection             Black/Grey Padlockable Handle – lockable in the OFF-position             Class II compliant, Grey Insulated Enclosure             Switch Interlocked with lid to prevent opening in “ON” position             Rated for use in ambient temperatures of 50°C UK Please note: We will have reduced availbility of K&N switch gear for the immediate future. We have sourced alternative options for this period of low stock, please contact your account manager for more information. Supplier Part No: KG20 T104/GB-P103 KL51V Weight: 0.43 kg Poles: 4 Max Cable: 6 mm2 Max Voltage: 460 V Rated Current: 25 A Rated Voltage: 220 V Rated Current: 21 A Rated Voltage: 280 V Rated Current: 20 A Rated Voltage: 340 V Rated Current: 18 A Rated Voltage: 400 V Rated Current: 11 A Rated Voltage: 460 V Established in 1907 in Austria, Kraus & Naimer has grown to be one of world's highest quality and largest switch manufacturer in the world. For over 100 years Kraus & Naimer have been manufacturing top quality electrical switches and now offer the widest range of solar photovoltaic AC and DC isolators on the market. Every solar PV system requires at least one DC disconnector to isolate the PV array from the input to the inverter and at least one AC disconnector to isolate the inverter from the mains supply. Choosing a well proven and high quality product for these small but vital parts of any PV system is essential and there is no safer choice than Kraus & Naimer.

Read more less

Part No: SUN-3.6-SUN-5.12 Storage Systems - Grid Backup Packages This part is a special offer made up of the following items: Part   1 x Sunsynk CATL Battery LFP 5.12kWh   1 x  Sunsynk 3.6kW AC 7kWp ECCO Hybrid Inverter   1 x  Battery Wall Mount Bracket Sunsynk   1 x  Battery to Inverter Cable Pack Long for Sunsynk CATL only   1 x  Jean Muller Fuse-switch-disconnector KETO size 00 body (battery isolator)   2 x  NH Fuse-link 125A for KETO-00     Weight: 75.57 kg Rated Power: 3,600 W

Read more less

This is the 4th generation of the SolaX Hybrid range, retaining all the key features of the 3rd generation while making some welcome improvements. The X-Hybrid is can also store surplus energy in batteries for later use. It is important to understand that this is a hybrid solar PV inverter and battery storage controller. This means it needs to be sized just like a regular inverter would be and, if it is being retrofitted, will replace the existing inverter. AC attributes Max power: 12000W Max current: 19.3A Number of phases: 3 DC attributes Max power 18000W Max Isc current 20A Max voltage 1000V Start up voltage 200V System Max efficiency 98% IP rating IP65 Weight 30kg Dimensions 503*503*199mm Key features In-built EPS changeover switch Supports up to 150% oversizing Can work at full capacity down to -35C 30A Charge/discharge capability On-grid and off-grid use Includes WiFi dongle

Read more less

Part No: EN-Q-TERM-3P Accessories - Cable termination caps Enphase round Q Cable 3 phase Terminator cap for unused cable ends - required to terminate each 3 phase circuit.  Single item only.    Supplier Part No:Q-TERM-3P Weight:0.28 kg

Read more less