INVERTERS FOR SOLAR / BATTERY STORAGE

Features Two AC Outputs The main output has no break functionality. The MultiPlus takes over the supply to the connected loads in the event of a grid failure or when shore/generator power is disconnected. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption. The second output is live only when AC is available on the input of the MultiPlus. Loads that should not discharge the battery, like a water heater for example can be connected to this output (second output available on models rated at 3 kVA and more). Virtually unlimited power thanks to parallel operation Up to 6 Multis can operate in parallel to achieve higher power output. Six 24/5000/120 units, for example, will provide 25 kW / 30 kVA output power with 720 Amps charging capacity. Three phase capability In addition to parallel connection, three units of the same model can be configured for three phase output. But that’s not all: up to 6 sets of three units can be parallel connected for a huge 75 kW / 90 kVA inverter and more than 2000 Amps charging capacity. PowerControl – Dealing with limited generator, shore side or grid power The MultiPlus is a very powerful battery charger. It will therefore draw a lot of current from the generator or shore side supply (nearly 10 A per 5 kVA Multi at 230 VAC). With the Multi Control Panel a maximum generator or shore current can be set. The MultiPlus will then take account of other AC loads and use whatever is extra for charging, thus preventing the generator or shore supply from being overloaded. PowerAssist – Boosting the capacity of shore or generator power This feature takes the principle of PowerControl to a further dimension. It allows the MultiPlus to supplement the capacity of the alternative source. Where peak power is so often required only for a limited period, the MultiPlus will make sure that insufficient shore or generator power is immediately compensated for by power from the battery. When the load reduces, the spare power is used to recharge the battery. Solar energy: AC power available even during a grid failure The MultiPlus can be used in off grid as well as grid connected PV and other alternative energy systems. Loss of mains detection software is available. System configuring In case of a stand-alone application, if settings have to be changed, this can be done in a matter of minutes with a DIP switch setting procedure. Parallel and three phase applications can be configured with VE.Bus Quick Configure and VE.Bus System Configurator software.   Brand Victron Energy Manufacturer Part Number PMP123021010 Voltage 12 Transfer Switch (A) 16 Cont. Output Power at 25°C (VA) 3000 Peak Power (W) 6000 Max Efficiency 93% Zero Load Power (W) 20 Charge Current House Battery (A) 120 Charge Current Starter Battery (A) 4 Battery Temperature Sensor Yes Programmable Relay Yes (3x) Remote on-off Yes Protection Category IP21 Dimensions H362 x W258 x D218mm Weight (kg) 19 Warranty 5 Years Country of Manufacture India

Read more less

It incorporates 4.3-inch LCD touch screen for monitoring and control.   Fully programmable RGB Light Ring around charging port, to quickly determine the device state. It can be programmed from the web interface to display different light effects based on the current state (disconnected, charging, charged etc.). The objective is to help the user see the current state from a distance.    GTIN 8719076051305 Input Voltage Range 170 – 265V AC Rated Charge Current 32A / phase Nominal Power 22kW Current Output Range 6 – 32A Data Communication Modbus TCP over WIFI Protection Category IP44 Dimensions H390 x W300 x D150mm Weight 3Kg Warranty 5 Years  

Read more less

Sunsynk Acure Hybrid Inverter & Smart Energy Management System (3.6kW–12kW) Warranty is applicable to 10 years when matched with a Sunsynk battery. Take full control of your energy with the Sunsynk Acure, a next-generation hybrid inverter and smart energy management system designed for seamless power optimisation, advanced safety, and effortless installation. Engineered for both residential and commercial solar installations, the Acure combines intelligent load management, integrated connectivity, and industry-leading protection features — all in one powerful, compact unit. Key Features & Benefits Smart Energy Management – Optimise energy usage with programmable wireless smart switches Expandable System – Connect up to 10 wireless smart switches for tailored load control Integrated 40A Smart Switch – Reliable power distribution built-in Advanced Connectivity – Built-in Bluetooth, Wi-Fi, LAN (Ethernet), and LoRa Real-Time Monitoring – Track generation, consumption, and battery performance User-Friendly Interface – New intuitive UI for installers and end users Automatic Load Shedding – Prioritises essential loads during power outages Multi-Colour LED Status Display – Instant system visibility Built for Performance & Flexibility The Sunsynk Acure hybrid inverter is available in: Single-phase: 3.6kW – 8kW Three-phase: 5kW – 12kW Suitable for: Solar PV systems Battery storage installations Wind turbine integration EV charging systems Hot water tank control Whether upgrading an existing system or installing new, Acure delivers high efficiency, scalability, and long-term reliability. Smarter Installation, Cleaner Finish Designed with installers in mind: Wireless CT coil reduces cabling requirements Hinged terminal cover for faster, safer access Discreet cable routing for a clean, professional finish IP65 rated – suitable for indoor & outdoor installation Advanced Safety & Protection Safety is at the core of the Sunsynk Acure system: Arc Fault Detection (AFCI) – Reduces fire risk Solar Panel Theft Detection – Alerts on tampering or disconnection Rapid Shutdown Capability Generator Compatibility – Dry contact start for backup power Integrated Protections Include: DC reverse polarity protection AC overcurrent & overvoltage protection Short circuit protection Thermal protection Ground fault & earth fault detection Residual current (RCD) monitoring Surge protection Islanding protection DC insulation monitoring ✔ G98 / G99 Compliant Total Control with Sunsynk Connect Pro Unlock full system visibility with Sunsynk Connect Pro: Monitor energy usage in real time Remote system control via mobile app Installer remote commissioning & diagnostics Multi-site fleet management for commercial users Firmware updates over the air Why Choose Sunsynk Acure? All-in-one hybrid inverter + energy management system Faster installs with wireless integration Advanced safety and protection features Scalable for homes, businesses, and commercial sites Fully compatible with modern smart energy ecosystems Perfect For Homeowners reducing energy bills Commercial energy optimisation Solar + battery storage systems Off-grid and backup power solutions Smart energy and load management setups Warranty & Support Inverter Warranty: 10 years 61.4kWh HV Battery: 10 years IP65 5.12kWh Battery: 5 years CATL 5.12kWh Battery: 10 years

Read more less

Harness the power of the sun day and night with this ground-breaking hybrid inverter from Fox ESS. Compatible with our range of high-voltage batteries for maximum round-trip efficiency. Available in a range from 5kW to 15kW, with up to 15kW charge/discharge capability. Engineered to last with an IP65 rating, making it suitable for outdoor installation. Enjoy easy installation with flexible configuration and plug and play setup. Monitor your system remotely via smartphone app or web portal with FoxCloud V2.0 Advanced System Monitoring. AC attributes Rated output power: 12kW Rated output current:EPS output power: 18.2A12kW Number of phases: 3 DC Attributes Max PV power 24kW Max Input CurrentMax Input Voltage 20A1000V Start up voltage 140V No. of MPPTsMPPT Range 3120 - 950V System Max Efficiency 97.9% IP Rating IP65 Weight 34 kg Dimensions 665 * 545 * 390 mm

Read more less

Part No: SOL-S6-EH3P50K-H Storage Systems - Hybrid Inverter Features: Allowable PV of up to 100kW, on the 180-1000V MPPT. 4-MPPTs, rated at 40A each, with 2-string inputs each allowing for 8 strings of high power/current PV modules. Supports Grid and Generator AC inputs. Parallel up to 6 x inverters for up to 300kW of back-up load. Battery Charge and Discharge current of up to 140A. UPS transfer time of less than 10ms. 160% surge power for 2s to accommodate inductive loads. Integrated AFCI (DC arc-fault circuit protection) – mitigating fire risks. LCD display and remote firmware upgrades with included S4 Wi-Fi/LAN Stick and Solis Cloud support/monitoring. Solis reliability with 5-year warranty. (extendable to 10/15/20-years) Current transformer ESCT-T50-300A/5A included in product packaging SA: NRS-097 certified and CoCT approved. IMPORTANT: The inverter supports a maximum battery charge and discharge of 140A. As each of the two battery ports support a maximum of 25mm2 cable/70A. If you require the 140A from a single battery/battery stack, you are required to connect your battery cables to a common bus bar for positive and negative and take a 25mm2 cable to each battery port on the inverter. Setting 1 BAT 2 DC on your inverter battery settings and connecting to BMS port 1.

Read more less

Part No: SOL-S6-EH3P30K-H Storage Systems - Hybrid Inverter Features: Allowable PV of up to 60kW, on the 180-1000V MPPT. 3-MPPTs, rated at 40A each, with 2-string inputs each allowing for 6 strings of high power/current PV modules. Supports Grid and Generator AC inputs. Parallel up to 6 x inverters for up to 300kW of back-up load. Battery Charge and Discharge current of up to 140A. UPS transfer time of less than 10ms. 160% surge power for 2s to accommodate inductive loads. Integrated AFCI (DC arc-fault circuit protection) – mitigating fire risks. LCD display and remote firmware upgrades with included S4 Wi-Fi/LAN Stick and Solis Cloud support/monitoring. Solis reliability with 5-year warranty. (extendable to 10/15/20-years) Current transformer ESCT-T50-300A/5A included in product packaging SA: NRS-097 certified and CoCT approved. Important The inverter supports a maximum battery charge and discharge of 140A. As each of the two battery ports support a maximum of 25mm^2 cable/70A. If you require the 140A from a single battery/battery stack, you are required to connect your battery cables to a common bus bar for positive and negative and take a 25mm^2 cable to each battery port on the inverter. Setting 1 BAT 2 DC on your inverter battery settings and connecting to BMS port 1.

Read more less

Part No: SOL-S6-EH3P15K-NV-YD-L Storage Systems - Hybrid Inverter Features: Allowable PV of up to 24kW, on the 200-1000V MPPT. 2-MPPTs, rated at 40A each, with 3-string inputs each allowing for 3 strings of 20A high power/current PV modules. Generator connectivity with automatic On/Off control. Parallel up to 6 inverters for up to 90kW of backup. 10 second, 200% surge power backup overload capability. 24 hour real-time intelligent energy management - Bluetooth/Wi-Fi/App. Uninterrupted power supply with 10ms reaction time. Comes with a Wi-Fi/LAN datalogger a 5-year warranty - extendable to 10-years.

Read more less

Part No: SOL-S6-EH3P15K-H Storage Systems - Hybrid Inverter Note: Including 3 current sensors for direct connection to the inverter

Read more less

Part No: SOL-S6-EH1P10K-L-PLUS-UK Storage Systems - Hybrid Inverter Solis Single Phase Low Voltage Energy Storage Inverters New PLUS model provides solutions for demanding power scenarios Features: Built-in Backup Port with Automatic UPS switching Up to 190A max charge/discharge current Up to 200% DC oversizing 6 customisable charge/discharge time settings 10 second 200% surge power backup overload capability Generator connectivity with multiple input methods and automatic generator On/Off control Supports 1ph and 3ph flexible connection with max 48kW in parallel Intelligent AC coupling scheme, easily upgrade existing grid-connected systems Supports peak shaving control in both "self-use" and "generator" mode Compatible with lead-acid and lithium batteries, with multiple battery protection features

Read more less

Part No: SOL-S6-EH3P-5.0K-H-UK Storage Systems - Hybrid Inverter Solis S6 5kW 3PH Hybrid Inverter 3 MPPTs, suitable for residential rooftop installations with multiple array orientations Supports Unbalanced and Half-Wave Loads on the Grid Port and on the Backup Port Compatible with multiple brands of battery models giving customers multiple battery options Supports up to 10 units in parallel on Grid and Backup. Suitable for small to medium level commercial energy storage systems Supports pure off grid applications with generator communication support  Multiple working modes to meet different use case scenarios  Controllable and Upgadeable via the SolisCloud App to avoide site visits Up to 16A of MPPT current input to support 182mm/210mm solar panels Up to 200% DC oversizing Up to 50A/10kW max charge/discharge rating with industry highest level 10kW of backup loads support capability  UPS level switching time (<10ms) supporting critical loads all the time High PV charge efficiency to prevent excess PV loss Safety protection with integrated AFCI function, which actively detects arc faults in the PV Array Natural convection design without external fans Please note: The inverter is supplied including the S2-WL-ST data logger stick (WiFi & LAN) and a 3PH meter from Eastron

Read more less

Part No: SOL-S6-EH3P20K-H Storage Systems - Hybrid Inverter Features: Integrated 4 MPPTs for multiple array orientations Up to 50A max charge/discharge current String current up to 20A, perfectly match large current modules 10 second 200% surge power backup overload capability Supports Max 6 pcs in parallel Up to 200% DC oversizing Supports Unbalanced and Half-Wave Loads on both the Grid and Backup Port Supports peak shaving control in both "self-use" and "generator" mode 6 customisable charge/discharge time settings Automatic UPS switching Intelligent AC coupling scheme, easily upgrade existing grid-connected systems Note: Including 3 current sensors for direct connection to the inverter Supplier Part No: S6-EH3P20K-H (Display) Weight: 53 kg Rated Power: 20,000 W Min PPT Voltage: 200 V Max PPT Voltage: 850 V DC Startup Voltage: 160 V DC Shutdown Voltage: 1,000 V Max Input Voltage: 1,000 V Max DC Power: 40,000 W Max AC Power (5 Minutes): 20,000 W Surge AC Power (1 Second): 22,000 W Max DC Current: 96 A Max DC Inputs: 6 Has DC Fuses: 0 Connector: MC4   Included Connectors: 4 Euro Efficiency: 97.7 % Transformer: N/A MPPT Quantity : 4 Has Integrated DC Switch: No Warranty: 5 years

Read more less

Part No: SYNKIP65-LONGCABL Cables - Battery Cable Price reduced from £61.30 on 23/10/2025

Read more less

Solis Mini Series Inverter Leading Features:• Max. efficiency 97.7%• Compact and lightweight• String current up to 14A• Super high frequency switching technology• Wide voltage range and low startup voltage• 2 MPPT design with precise MPPT algorithm• Intergrated Export Power Manager (EPM)• Integrated AFCI (DC arc-fault circuit protection)• Friendly and adaptable connection to the grid Manufacturer        Solis Phases          1 Phase Power Rating         kW2.5 Inverter Type         String Inverter Built in DC       Yes No. of MPPT       2 Built in Communication        Optional Commodity Code          85044085 Dimensions (mm) (H x W x D)      543 x 310 x 160

Read more less

Max. efficiency 98.7% String current up to 16A Wide voltage range and low startup voltage AFCI protection proactively reduces fire risk Supports export power control Supports RS485 WiFi GPRS Scan to register on SolisCloud supports remote upgrade and control Automatic voltage stabilization technology in weak gridconditions Compact design simple installation and maintenance Supports high power modules for lower installation costs > 150% DC/AC ratio IP66 Application        Commercial Manufacturer        Solis Phases         3 Phase Power Rating           kW12 Inverter Type        String Inverter Built in DC         Yes No. of MPPT         2 Built in Communication         Optional Commodity Code        85044086 Dimensions (mm) (H x W x D)        563 x 310 x 219

Read more less

The Sunsynk 20kW three-phase hybrid inverter is an ideal solution to reduce your electricity costs and manage power from various energy sources. Whether it's solar panels, batteries, the national grid, a generator or even a wind turbine, this hybrid inverter can handle it all. This versatile inverter is ideal for both home and business use and is scalable, so you can expand it as required. With inputs for PV solar, AC grid power, batteries and a generator, this inverter can deliver a continuous power output of 20000W. This three-phase inverter can charge both lead-acid and lithium-ion batteries, and innovatively works to balance the load across the three phases to avoid overloading. With seamless energy load balancing, this inverter can handle a load distribution of 20% on one phase, 20% on another, and 60% on the third phase, while still delivering perfect phase rotation. Key features: Easy-to-understand display Supports Wi-Fi or GSM monitoring Compatible with lithium-ion and lead-acid batteries Smart-settable three-stage MPPT charging for optimised battery performance Compatible with mains electrical grid voltages, power generators or wind turbines DC- and AC-coupled to retrofit to existing solar system Programmable supply priority for battery or grid High reliability and response speed Programmable export Works on or off-grid and with up to sixteen modules in parallel Can operate in single-phase or three-phase mode Dimensions: 408mm (W) x 638mm (H) x 237mm (D) Weight: 38.5kg Rated IP65 for ingress protection Five-year standard warranty  

Read more less

Compatible Products Hanchu High Voltage Battery 9.4kWh Hanchu High Voltage Battery 9.4kWh - BMS   Ultra Performance Exceptional Efficiency Achieves up to 98.8% peak efficiency, maximising the conversion of generated energy into usable power and significantly reducing energy costs. Robust Power Handling Supports up to 110% AC output overloading and up to 120% back-up output overloading for 60 seconds, ensuring reliable performance even during peak demand. Advanced Multi-MPPT Support Equipped with 4 MPPTs, enabling optimal solar energy capture across multiple roof orientations and shading conditions to maximise overall solar utilization. Reliable Operation Ultra-Fast Switching Time With EPS switching time of less than 20 milliseconds, it ensures continuity of critical operations without interruption during power outages. Broad Voltage Compatibility Supports an extensive battery voltage range from 135V to 750V, making it compatible with various high-voltage battery systems for greater versatility. Comprehensive Safety Protection Offers built-in surge protection, insulation resistance monitoring, and multi-layered safeguards against over-temperature and residual currents, ensuring protection for both the equipment and the premises. Easy Maintenance Remote Management Easily manage settings and monitor performance via the iESS and Hanchu app, offering convenience and real-time control. Easy Installation The horizontal design and quick plug-in terminals enable fast and convenient installation, minimising labour time and reducing complexity. Advanced Connectivity Offers simple configuration through WiFi via the iESS platform, streamlining setup and integration into existing systems. PV Input Max. PV array power : 75.0kW Max. input voltage : 1000V MPPT voltage range / rated input voltage : 200-850V Min. input voltage / start voltage : 135V No. of independent MPPT trackers / strings per MPPT input : 4 Max. input current per MPP tracker : 30A Max. short-circuit current per MPP tracker : 40A Battery Input Nominal battery voltage : / Battery voltage range : 135-750V Max. charging / discharge power : 50000W Max. charging current / Max. discharging current : 100A Battery type : LFP AC Output AC voltage range / Nomlnal AC voltage : 3L/N/PE;220/380V;230/400V;240/415V Rated AC grid frequency : 50Hz/ 60Hz Rated apparent power : 50.0kW Max. apparent power : 55.0kVA Rated grid output current (@230V) : / Max. grid output current : 83.0A AC Input Rated grid voltage : 3L/N/PE;220/380V;230/400V;240/415V Rated apparent power : 50.0kW Max. input apparent power from grid : 60.0kVA Rated input curent from grid : / Max. input current from grid : / EPS Output Nominal output voltage : 3L/N/PE;220/380V;230/400V;240/415V Nominal output frequency : 50Hz/ 60Hz Rated apparent power : 50.0kW Max. output apparent power : 55.0kVA Peak output apparent power : 60kVA | 60s Max. output current : 83.0A Max. switch time : ＜20ms Efficiency MPPT efficiency : 98.80% Euro efficiency / Max. efficiency : 98.30% Max. battery to load efficiency : / General Data Dimensions (W*H*D) (mm) : 800*620*300 Device weight : 76.0Kg Operating temperature range : -30℃~+60℃ Noise emissions (typical) : ＜50dB Standby consumption : ＜15W Degree of protection (as per lEC 60529) : IP65 Features User interface : OLED&LED&APP Communication with BMS : / Communication with meter : / Communication with portal : / Other communication : / Communication : RS485/CAN/WiFi/LAN(Optional) Integrated power control / Zero export control : Integrated/Integrated Certifications : IEC 62109/EN 61000/EN 50549-1/NTS/VDE-4105/G99/G100/CEI/NRS 097/CEI 0-21/NEN Warranty : 12 years

Read more less

Fox ESS AI Link The parallel function (installing multiple units on a single site).  Require an additional EMS.

Read more less

Technical Features Efficiency (max.) inverter: 98% Efficiency (EU) inverter: 97.5% MPPT voltage range (VDC): 200-850V Input current (max.): 16A Input voltage (VDC max.): 1000B DC Power (max.): 16kW Manufacturers warranty: 5 years Nominal voltage: 600V Inverter protection class: IP66 Rated capacity: 10kW Battery technology: Lithium ion Promotion.        Solis Pylon Combo Manufacturer.      Solis Inverter Type.       Hybrid Inverter No. of MPPT.         4 Commodity Code.         85044086 Dimensions.      (mm) (H x W x D)563 x 546 x 235

Read more less

Product features Mains connection: 3-phase AC output: 8 kVA 8 kW emergency power output via separate output MPP tracker: 4 with 1 string output each Max. short circuit current per MPPT: 24 A Max. input current: 16 A Communcations: CAN, RS485, Wi-Fi 3-phase smart meter with 3 current transformers included Incl. WiFi+LAN kit Protection category: IP66 Warranty: 5 years Manufacturer.     Solis Phases.     3 Phase Power.     Rating kW8 Inverter Type.      Hybrid Inverter No. of MPPT.     4 Commodity Code.       85044086 Dimensions.       (mm) (H x W x D)496 x 596 x 230  

Read more less

 Available models: 150A / 70V – 4 high current connections 150A / 70V – 6 high current connections 250A / 70V – 4 high current connections 600A / 70V – 4 high current connections and 8 low current connections 600A / 70V – 8 high current connections and 8 low current connections  For more technical information and for the busbar dimensions see the datasheet.   Brand Victron Energy Manufacturer Part Number VBB125040010 GTIN 8719076052210 Maximum Current 250A Maximum Voltage 70VDC Terminal Diameter 8mm Terminal Height 17mm Dimensions H48 x W237 x D70mm Weight 0.45Kg Warranty 5 Years

Read more less

The device is technically identical to the EV Charging Station, but with a new, modern design available in 3 colours and without the built-in LCD screen. Initial setup, configuration and monitoring is done from VictronConnect via Bluetooth and/or the integrated web interface via a WiFi Access Point or a WiFi LAN. The charger can be fully integrated with and remotely controlled via a Victron Energy GX Device and VRM Not only does this EV Charging Station NS fully integrate with a Victron Energy GX device and VRM, if you have solar (within the Victron ecosystem), it can also be set up to allow excess energy from the sun to directly charge your vehicle. Manual and scheduled modes offer even more flexibility to respond to the needs of the EV depending on the system. It has a fully programmable RGB light ring around the charging port that displays different light effects depending on the current status (disconnected, charging, charged, etc.) to quickly determine the device status.   Features WiFi Communication WiFi: 802.11 b/g/n for configuration, monitoring and control. The internal WiFi module can be configured in Access Point or Station mode for both, the initial setup and monitoring. Easy operation and control via Bluetooth and the VictronConnect App Get full control and overview of all operating parameters and session statistics at a glance. Light Ring for fast viewing the device state Fully programmable RGB Light Ring around the charging port to quickly determine the device state. It can be programmed from the integrated web interface to display different light effects based on the current state (disconnected, charging, charged etc.). Three working modes available: 1. Manual Mode to configure output current Manual mode allows configurable output current between 6-32 A. The charging power can be regulated in different ways: by using the web interface, from a GX device and VRM and via VictronConnect. It allows to manually start or stop the charging process when a vehicle is connected to the charging station. 2. Automatic Mode to ensure maximum PV system efficiency Detects when excess power is available and uses only that power to charge the vehicle. 3. Scheduled Mode to charge the EV at certain time intervals A fully programmable scheduler allows charging at different time intervals, for example at certain times during the night when grid energy is cheaper. Integration with GX devices and VRM Control and monitor the EV Charging Station NS from a GX device touch display and the Remote Console and the VRM Portal. The VRM Portal also offers real time and custom reports for configurable time periods.

Read more less

The Fox system is easy to install and will save you time spent on installation. Remote monitoring is also avalible via your smartphone or web portal. Compatible with: ECS2900  Compatible with: ECS4100  Compatible with: ECS4300  Compatible with: ECS4800  Compatible with: HV2600  IP65 rated - suitable for outdoor installations Remote monitoring via web portal or smartphone Easy to expand battery capacity Dual MPPT - ensure optimal solar production High round-trip efficiency of 97%   CT Clamps and WiFi stick are included in the box. A second CT will be required if there's another generator set (i.e PV, wind or other). A meter will be required for >30m distance between inverter and incoming power connection point. Don't forget: You must register your install with Fox online to activate the 10 year product warranty, otherwise it's 5 years as standard. Please click here for registration page. Please check the warranty document for more information. Supplier Part No: FE-H1-3.0-G2 Weight: 22 kg Rated Power: 3,000 W Min PPT Voltage: 80 V Max PPT Voltage: 550 V DC Startup Voltage: 75 V DC Shutdown Voltage: 601 V Max Input Voltage: 600 V Max DC Power: 4,500 W Max AC Power (5 Minutes): 3,000 W Surge AC Power (1 Second): 3,300 W Max DC Current: 32 A Max DC Inputs: 2 Has DC Fuses: 0 Connector: MC4   Included Connectors: 4 Euro Efficiency: 97 % Transformer: None MPPT Quantity : 2 Has Integrated DC Switch: Yes Warranty: 5 years

Read more less

Technical Features  4 Integrated MPPTs and 8 strings with string current capacity of up to 20A Backup port supports 1.6 times/2 seconds overload Supports maximum 96kW usable PV input power Enables peak shaving control in both "self-use" and "generator" modes Compatible with a wide voltage range to accommodate various batteries Increased battery protection and operation features to extend battery life Allows parallel operation of up to 6 units for both on-grid and off-grid application Generator connectivity with multiple input methods and automatic generator On/Off control Maximum charge/discharge current of up to 140A/70A+70A on two independently controlled battery ports

Read more less

Fox ESS H3 Pro 15.0 three-phase hybrid inverter 3 MPP tracker Full three-phase emergency power capability Two battery inputs for even easier connection of high-voltage batteries  Modern and functional design Remote monitoring 10-year warranty (5 years as standard and extendable to 10 years through registration) Smart meter and WiFi dongle are included in the scope of delivery Note: For specific battery sizing, please see the attached Battery Sizing Guide below   Supplier Part No: FE-H3-PRO-15.0 Weight: 52.5 kg Rated Power: 15,000 W Min PPT Voltage: 160 V Max PPT Voltage: 1,000 V DC Startup Voltage: 160 V DC Shutdown Voltage: 1,000 V Max Input Voltage: 1,000 V Max DC Power: 22,500 W Max AC Power (5 Minutes): 15,000 W Surge AC Power (1 Second): 16,500 W Max DC Current: 32 A Max DC Inputs: 6 Has DC Fuses: 1 Connector: MC4   Included Connectors: 3 Euro Efficiency: 97.3 % Transformer: N/A MPPT Quantity : 6 Has Integrated DC Switch: Yes Warranty: 5 years

Read more less

Part No: FE-T-17.0 Inverters - Main Units Rating: 17,000W Phases: 3 FOX ESS - PV Inverter - T Series - 17.0kW T17-G3 Don't forget: You must register your install with Fox online to activate the 10 year product warranty, otherwise it's 5 years as standard. Supplier Part No: T17 Weight: 20 kg Rated Power: 17,000 W Min PPT Voltage: 140 V Max PPT Voltage: 1,100 V DC Startup Voltage: 140 V DC Shutdown Voltage: 1,100 V Max Input Voltage: 1,100 V Max DC Power: 25,500 W Max AC Power (5 Minutes): 17,000 W Surge AC Power (1 Second): 18,700 W Max DC Current: 28 A Max DC Inputs: 4 Has DC Fuses: 4 Connector: MC4   Included Connectors: 4 Euro Efficiency: 97.8 % Transformer: N/A MPPT Quantity : 2 Has Integrated DC Switch:Yes Warranty: 5 years

Read more less

Part No: FE-T-6.0 Inverters - Main Units Rating: 6,000W Phases: 3 FOX ESS - PV Inverter - T Series - 6.0kW T6-G3 Don't forget: You must register your install with Fox online to activate the 10 year product warranty, otherwise it's 5 years as standard. Supplier Part No: T6 Weight: 17 kg Rated Power: 6,000 W Min PPT Voltage: 140 V Max PPT Voltage: 1,100 V DC Startup Voltage: 140 V DC Shutdown Voltage: 1,100 V Max Input Voltage: 1,100 V Max DC Power: 9,000 W Max AC Power (5 Minutes): 6,000 W Surge AC Power (1 Second): 6,600 W Max DC Current: 14 A Max DC Inputs: 2 Has DC Fuses: 2 Connector: MC4   Included Connectors: 2 Euro Efficiency: 97.8 % Transformer: N/A MPPT Quantity : 2 Has Integrated DC Switch: Yes Warranty: 5 years

Read more less

Part No: FE-F6000 Inverters - Main Units Rating: 6,000W Phases: 1 FOX ESS - PV Inverter - F Series - 6kW F6000 Our Dual-MPPT F Series range includes 3.0 - 6.0kW models. The F Series is IP65 rated and battery ready for easy upgrade when paired with a Fox ESS charge controller. High Performance: Low start-up voltage, wide voltage range, 97.4% maximum efficiency. Easy Installation: Flexible configuration, plug and play set-up. IP65 Rated: Engineered to last with maximum flexibility. Suitable for outdoor installation. Remote Monitoring: Monitor your system remotely via smartphone app or web portal. Don't forget: You must register your install with Fox online to activate the 10 year product warranty, otherwise it's 5 years as standard. Supplier Part No: F6000 Weight: 15.5 kg Rated Power: 6,000 W Min PPT Voltage: 120 V Max PPT Voltage: 600 V DC Startup Voltage: 120 V DC Shutdown Voltage: 601 V Max Input Voltage: 600 V Max DC Power: 9,000 W Max AC Power (5 Minutes): 6,000 W Surge AC Power (1 Second): 0 W Max DC Current: 25 A Max DC Inputs: 2 Has DC Fuses: 0 Connector: MC4   Included Connectors: 0 Euro Efficiency: 96.8 % Transformer: HF MPPT Quantity : 2 Has Integrated DC Switch: Yes Warranty: 5 years

Read more less

Part No: FE-S1000 Inverters - Main Units Rating: 1,000W Phases: 1 FOX ESS - PV Inverter - S Series - 1.0kW S1000-G2 Don't forget: You must register your install with Fox online to activate the 10 year product warranty, otherwise it's 5 years as standard. Supplier Part No: S1000 Weight: 5.4 kg Rated Power: 1,000 W Min PPT Voltage: 60 V Max PPT Voltage: 500 V DC Startup Voltage: 60 V DC Shutdown Voltage: 500 V Max Input Voltage: 500 V Max DC Power: 1,500 W Max AC Power (5 Minutes): 1,000 W Surge AC Power (1 Second): 1,100 W Max DC Current: 14 A Max DC Inputs: 1 Has DC Fuses: 1 Connector: MC4   Included Connectors: 1 Euro Efficiency: 96.5 % Transformer: N/A MPPT Quantity : 1 Has Integrated DC Switch: Yes Warranty: 5 years

Read more less

Brand CTEK Product Code 56-629 Barcode (EAN) 7350009566292

Read more less

Charging Specifications: • Charges 24V Batteries • Charges batteries of 8Ah - 100Ah • Trickle charges batteries of 8Ah - 250Ah • Can charge all Lead-Acid type batteries (WET, MF, CA-CA, AGM, GEL) • Comes with a 3 pin mobility connector   Brand CTEK Charge Voltage 24 V Charge Rate 4 A Other References Mobility 3 Pin Plug 24V Charge Capacity (up to) 8 Ah - 100 Ah Trickle Charge 8 Ah - 250 Ah Guarantee 2 Years Barcode (EAN) 7350009567787

Read more less

Charging Specifications: • Charges 24V Batteries • Charges batteries of 28Ah - 300Ah • Trickle charges batteries of 28Ah - 500Ah • Can charge all Lead-Acid batteries (WET, MF, CA-CA, GEL, EFB, AGM) • Comes with croc clips Brand CTEK Charge Voltage 24 V Charge Rate 14 A 24V Charge Capacity (up to) 28 Ah - 300 Ah Trickle Charge 28 Ah - 500 Ah Guarantee 2 Years Barcode (EAN) 7350009567688  

Read more less

Charging Specifications: • Charges 12V Batteries • Charges batteries of 40Ah - 500Ah and 30Ah - 450Ah(Lithium) • This charger does not have a trickle charge option • Can charge WET, GEL, EFB, AGM and Lithium batteries • Comes with croc clips   Brand CTEK Charge Voltage 12 V Charge Rate 25 A Length 235 mm Width 130 mm Height inc. terms 65 mm 12V Charge Capacity (up to) 40 Ah - 500 Ah Lithium Charge Capacity (up to) 30 Ah - 450 Ah Guarantee 2 Years Barcode (EAN) 7340103401988

Read more less

Charging Specifications: • Charges 12V Batteries • Charges batteries of 3Ah - 180Ah • Can charge all types of Lead-Acid batteries (WET, MF, CA-CA, GEL and optimised for EFB and AGM batteries. Also suitable for lithium batteries. • Comes with croc clip connectors   Brand CTEK Charge Voltage 12 V Charge Rate 8 A 12V Charge Capacity (up to) 3 Ah - 85 Ah Lithium Charge Capacity (up to) 3 Ah - 85 Ah Guarantee 5 Years

Read more less

Features Unique PowerAssist feature The Quattro will prevent overload of a limited AC source, such as a generator or shore power connection. First, battery charging will automatically be reduced when otherwise an overload would occur. The second level will boost the output of a generator or shore side supply with power taken from the battery. Virtually unlimited power thanks to parallel operation Up to 6 Quattros can operate in parallel to achieve higher power output. Three phase or split phase operation is also possible. Please check our datasheets to see which models have paralleling, three phase and split phase capabilities. Remote Monitoring and Control Monitor and control your Quattro and system or systems’ locally (LAN) or remotely via the internet from anywhere in the world, using the free VRM app. Access can be from a phone, tablet, laptop or PC for multiple operating systems. There is no end to the level of control, via the required Color Control GX or Venus GX, from adjusting your Quattro to setting a Geofence for hire vehicles and more… Split phase and three phase capability Two units can be configured for split phase, and three units can be configured for three phase output. But that’s not all: up to 6 sets of three units can be parallel connected to provide 144kW / 180kVA inverter power and more than 2500A charging capacity. For more detail please enter parallel in the search box on our website. Solar energy: AC power available even during a grid failure The Quattro can be used in off grid as well as grid connected PV and other alternative energy systems. Loss of mains detection software is available. System configuring In case of a stand-alone application, if settings have to be changed, this can be done in a matter of minutes with a DIP switch setting procedure. Parallel and three phase applications can be configured with VE.Bus Quick Configure and VE.Bus System Configurator software. Off grid, grid interactive and self-consumption applications, involving grid-tie inverters and/or MPPT Solar Chargers can be configured with Assistants (dedicated software for specific applications).   Brand Victron Energy Manufacturer Part Number QUA123020010 Voltage 12 Transfer Switch (A) Yes Cont. Output Power at 25°C (VA) 3000 Peak Power (W) 6000 Max Efficiency 93% Zero Load Power (W) 20 Charge Current House Battery (A) 120 Charge Current Starter Battery (A) 4 (12V and 24V models only) Battery Temperature Sensor Yes Programmable Relay 3x Remote on-off Yes Protection Category IP21 Dimensions H362 x W258 x D218mm Weight (kg) 19 Warranty 5 Years Country of Manufacture India

Read more less

Features Uninterrupted AC power (UPS function) In the event of a grid failure, or when shore or generator power is disconnected, the inverter within the Multi is automatically activated and takes over the supply to the connected loads. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption.   Remote Monitoring and Control Monitor and control your MultiPlus and system or systems’ locally (LAN) or remotely via the internet from anywhere in the world, using the free VRM app and free VRM portal website. Access can be from a phone, tablet, laptop or PC for multiple operating systems. There is no end to the level of control, via the required Color Control GX or Venus GX, from adjusting your MultiPlus to setting a Geofence for hire vehicles and more…   Proven reliability The full bridge plus toroidal transformer topology has proven its reliability over many years. The inverter is short circuit proof and protected against overheating, whether due to overload or high ambient temperature.    PowerControl – Dealing with limited generator, shore side or grid power With the Multi Control Panel a maximum generator or shore current can be set. The MultiPlus will then take account of other AC loads and use whatever is extra for charging, thus preventing the generator or shore supply from being overloaded.   PowerAssist – Boosting the capacity of shore or generator power Where peak power is so often required only for a limited period, the MultiPlus will make sure that insufficient shore or generator power is immediately compensated for by power from the battery. When the load reduces, the spare power is used to recharge the battery. High start-up power Needed to start high inrush loads such as power converters for LED lamps, halogen lamps or electric tools   Programmable relay By default, the programmable relay is set as an alarm relay, i.e. the relay will de-energise in the event of an alarm or a pre-alarm (inverter almost too hot, ripple on the input almost too high, battery voltage almost too low).   Brand Victron Energy Manufacturer Part Number PMP242120000 Voltage 24 Transfer Switch (A) 16 Cont. Output Power at 25°C (VA) 1200 Peak Power (W) 2400 Max Efficiency 94% Zero Load Power (W) 9 Charge Current House Battery (A) 25 Charge Current Starter Battery (A) 1 (12V and 24V models only) Battery Temperature Sensor Yes Programmable Relay Yes Remote on-off On/off/charger only Protection Category IP21 Dimensions H406 x W250 x D100mm Weight (kg) 8.2 Warranty 5 Years Country of Manufacture China

Read more less

Features Uninterrupted AC power (UPS function) In the event of a grid failure, or when shore or generator power is disconnected, the inverter within the Multi is automatically activated and takes over the supply to the connected loads. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption Remote Monitoring and Control Monitor and control your MultiPlus and system or systems’ locally (LAN) or remotely via the internet from anywhere in the world, using the free VRM app and free VRM portal website. Access can be from a phone, tablet, laptop or PC for multiple operating systems. There is no end to the level of control, via the required Color Control GX or Venus GX, from adjusting your MultiPlus to setting a Geofence for hire vehicles and more… Proven reliability The full bridge plus toroidal transformer topology has proven its reliability over many years. The inverter is short circuit proof and protected against overheating, whether due to overload or high ambient temperature.  PowerControl – Dealing with limited generator, shore side or grid power With the Multi Control Panel a maximum generator or shore current can be set. The MultiPlus will then take account of other AC loads and use whatever is extra for charging, thus preventing the generator or shore supply from being overloaded. PowerAssist – Boosting the capacity of shore or generator power Where peak power is so often required only for a limited period, the MultiPlus will make sure that insufficient shore or generator power is immediately compensated for by power from the battery. When the load reduces, the spare power is used to recharge the battery. High start-up power Needed to start high inrush loads such as power converters for LED lamps, halogen lamps or electric tools Programmable relay By default, the programmable relay is set as an alarm relay, i.e. the relay will de-energise in the event of an alarm or a pre-alarm (inverter almost too hot, ripple on the input almost too high, battery voltage almost too low). Brand Victron Energy Manufacturer Part Number PMP481500000 Voltage 48 Transfer Switch (A) 16 Cont. Output Power at 25°C (VA) 500 Peak Power (W) 900 Max Efficiency 92% Zero Load Power (W) 7 Charge Current House Battery (A) 6 Charge Current Starter Battery (A) 1 (12V and 24V models only) Battery Temperature Sensor Yes Programmable Relay Yes Remote on-off On/off/charger only Protection Category IP21 Dimensions H311 x W182 x D100mm Weight (kg) 4.4 Warranty 5 Years Country of Manufacture India

Read more less

It covers all DC terminals, preventing accidental or inquisitive contact with terminal screws. Brand Victron Energy Manufacturer Part Number SCC950400300 Warranty 5 Years

Read more less

Brand Victron Energy Manufacturer Part Number CIP100400060 Warranty 5 Years Country of Manufacture Slovenia    

Read more less

The IP65 rating makes this charger especially suitable for marine, mobile, and industrial applications and it can withstand the rigors of an adverse environment: heat, humidity and salt air. Features Skylla-IP65 (3): three full current outputs to charge 3 battery banks The Skylla-IP65 (3) features 3 isolated outputs. All outputs can supply the full rated output current. IP65 protection Steel epoxy powder coated case. Withstands the rigors of an adverse environment: heat, humidity and salt air. Circuit boards are protected with an acrylic coating for maximum corrosion resistance. Temperature sensors ensure that power components will always operate within specified limits, if needed by automatic reduction of output current under extreme environmental conditions. LCD display For status monitoring and to easily adapt the charge algorithm to a particular battery and its conditions of use. CAN-bus interface (NMEA2000) To connect to a CAN-bus network, to a Skylla-i Control panel or to the Color Control digital display. Synchronised parallel operation Several chargers can be connected in parallel and synchronised with help of the CAN-bus interface. This is achieved by simply interconnecting the chargers with RJ45 UTP-cables. The right amount of charge for a lead-acid battery: variable absorption time When only shallow discharges occur the absorption time is kept short in order to prevent overcharging of the battery. After a deep discharge the absorption time is automatically increased to make sure that the battery is completely recharged. Preventing damage due to excessive gassing: the BatterySafe mode If, in order to quickly charge a battery, a high charge current in combination with a high absorption voltage has been chosen, the Skylla-IP65 will prevent damage due to excessive gassing by automatically limiting the rate of voltage increase once the gassing voltage has been reached. Less maintenance and aging when the battery is not in use: the Storage mode The Storage mode kicks in whenever the battery has not been subjected to discharge during 24 hours. In the storage mode float voltage is reduced to 2,2 V/cell (26,4 V for 24 V battery) to minimise gassing and corrosion of the positive plates. Once a week the voltage is raised back to the absorption level to ‘refresh’ the battery. This feature prevents stratification of the electrolyte and sulphation, a major cause of early battery failure. To increase battery life: temperature compensation Every Skylla-IP65 comes with a battery temperature sensor. When connected, charge voltage will automatically decrease with increasing battery temperature. This feature is especially recommended for sealed lead-acid batteries and/or when important fluctuations of battery temperature are expected. Battery voltage sense In order to compensate for voltage loss due to cable resistance, the Skylla-IP65 is provided with a voltage sense facility so that the battery always receives the correct charge voltage. Use as a power supply As a result of the excellent control circuit, the Skylla-IP65 can be used as a power supply with perfectly stabilized output voltage if batteries or large buffer capacitors are not available. Li-Ion (LiFePO4) ready Simple charger on-off control can be implemented by connecting a relay or open collector opto coupler output from a Li-Ion BMS to the remote control port of the charger. Alternatively complete control of voltage and current can be achieved by connecting to the CAN-bus port. Brand Victron Energy Manufacturer Part Number SKY012070100 GTIN 8719076051978 Input Voltage 120/230V Input Voltage Range 90-265V Maximum AC input current @ 100 12A Charge current 3 x 70A Charge current starter batt. n.a Charge Algorithm 7 stage adaptive Battery Capacity 350-700Ah Charge algorithm, Li-Ion 3 stage, with on-off control or CAN-bus control Temperature Sensor Yes Can Be Used As Power Supply Yes Remote on-off Yes (can be connected to a Li-Ion BMS) CAN-bus communication port (VE.Can) Two RJ45 connectors, NMEA2000 protocol, not isolated Synchronised Parallel Operation Yes, with VE.Can Battery-Connection M6 bolts Dimensions H401 x W265 x D151mm Weight 6Kg Warranty 5 Years

Read more less

The IP65 rating makes this charger especially suitable for marine, mobile, and industrial applications and it can withstand the rigors of an adverse environment: heat, humidity and salt air. Features Skylla-IP65 (3): three full current outputs to charge 3 battery banks The Skylla-IP65 (3) features 3 isolated outputs. All outputs can supply the full rated output current. IP65 protection Steel epoxy powder coated case. Withstands the rigors of an adverse environment: heat, humidity and salt air. Circuit boards are protected with an acrylic coating for maximum corrosion resistance. Temperature sensors ensure that power components will always operate within specified limits, if needed by automatic reduction of output current under extreme environmental conditions. LCD display For status monitoring and to easily adapt the charge algorithm to a particular battery and its conditions of use. CAN-bus interface (NMEA2000) To connect to a CAN-bus network, to a Skylla-i Control panel or to the Color Control digital display. Synchronised parallel operation Several chargers can be connected in parallel and synchronised with help of the CAN-bus interface. This is achieved by simply interconnecting the chargers with RJ45 UTP-cables. The right amount of charge for a lead-acid battery: variable absorption time When only shallow discharges occur the absorption time is kept short in order to prevent overcharging of the battery. After a deep discharge the absorption time is automatically increased to make sure that the battery is completely recharged. Preventing damage due to excessive gassing: the BatterySafe mode If, in order to quickly charge a battery, a high charge current in combination with a high absorption voltage has been chosen, the Skylla-IP65 will prevent damage due to excessive gassing by automatically limiting the rate of voltage increase once the gassing voltage has been reached. Less maintenance and aging when the battery is not in use: the Storage mode The Storage mode kicks in whenever the battery has not been subjected to discharge during 24 hours. In the storage mode float voltage is reduced to 2,2 V/cell (26,4 V for 24 V battery) to minimise gassing and corrosion of the positive plates. Once a week the voltage is raised back to the absorption level to ‘refresh’ the battery. This feature prevents stratification of the electrolyte and sulphation, a major cause of early battery failure. To increase battery life: temperature compensation Every Skylla-IP65 comes with a battery temperature sensor. When connected, charge voltage will automatically decrease with increasing battery temperature. This feature is especially recommended for sealed lead-acid batteries and/or when important fluctuations of battery temperature are expected. Battery voltage sense In order to compensate for voltage loss due to cable resistance, the Skylla-IP65 is provided with a voltage sense facility so that the battery always receives the correct charge voltage. Use as a power supply As a result of the excellent control circuit, the Skylla-IP65 can be used as a power supply with perfectly stabilized output voltage if batteries or large buffer capacitors are not available. Li-Ion (LiFePO4) ready Simple charger on-off control can be implemented by connecting a relay or open collector opto coupler output from a Li-Ion BMS to the remote control port of the charger. Alternatively complete control of voltage and current can be achieved by connecting to the CAN-bus port. Brand Victron Energy Manufacturer Part Number SKY024035100 Input Voltage 120/230V Input Voltage Range 90-265V Maximum AC input current @ 100 12A Charge current 3 x 35A Charge current starter batt. n.a Charge Algorithm 7 stage adaptive Battery Capacity 150-350Ah Charge algorithm, Li-Ion 3 stage, with on-off control or CAN-bus control Temperature Sensor Yes Can Be Used As Power Supply Yes Remote on-off Yes (can be connected to a Li-Ion BMS) CAN-bus communication port (VE.Can) Two RJ45 connectors, NMEA2000 protocol, not isolated Synchronised Parallel Operation Yes, with VE.Can Battery-Connection M6 bolts Dimensions H401 x W265 x D151mm Weight 6Kg Warranty 5 Years Country of Manufacture Malaysia

Read more less

Features Perfect chargers for any type of battery Charge voltage can be precisely adjusted to suit any sealed or unsealed battery system. In particular, sealed maintenance free batteries must be charged correctly in order to ensure a long service life. Overvoltage will result in excessive gassing and venting of a sealed battery. The battery will dry out and fail. Suitable for AC and DC supply (AC-DC and DC-DC operation) Except for the 3-phase input models, the chargers also accept a DC supply. Controlled charging Every TG Charger has a microprocessor, which accurately controls the charging in three steps. The charging process takes place in accordance with the IUoUo characteristic and charges more rapidly than other processes. Use of TG Chargers as a power supply As a result of the perfectly stabilized output voltage, a TG Charger can be used as a power supply if batteries or large buffer capacitors are not available. Two outputs to charge 2 battery banks (24V models only) The TG Chargers feature 2 isolated outputs. The second output, limited to approximately 4A and with a slightly lower output voltage, is intended to top up a starter battery. To increase battery life: temperature compensation Every Skylla TG Charger comes with a battery temperature sensor. When connected, charge voltage will automatically decrease with increasing battery temperature. This feature is especially recommended for sealed batteries which otherwise might be overcharged and dry out due to venting. Battery voltage sense In order to compensate for voltage loss due to cable resistance, TG Chargers are provided with a voltage sense facility so that the battery always receives the correct charge voltage.   Brand Victron Energy Manufacturer Part Number SDTG2400503 Voltage 24 Charger Current House Battery 50A Charger Current Starter Battery 4A Recommended Battery Capacity 250 – 500Ah Battery Connection M8 Studs Outputs 1+1 Temperature Sensor Yes Can Be Used As Power Supply Yes IP Rating IP21 Dimensions H365 x D250 x 147mm Weight (kg) 5.5 Warranty 5 Years

Read more less

Features Perfect chargers for any type of battery Charge voltage can be precisely adjusted to suit any sealed or unsealed battery system. In particular, sealed maintenance free batteries must be charged correctly in order to ensure a long service life. Overvoltage will result in excessive gassing and venting of a sealed battery. The battery will dry out and fail. Suitable for AC and DC supply (AC-DC and DC-DC operation) Except for the 3-phase input models, the chargers also accept a DC supply. Controlled charging Every TG Charger has a microprocessor, which accurately controls the charging in three steps. The charging process takes place in accordance with the IUoUo characteristic and charges more rapidly than other processes. Use of TG Chargers as a power supply As a result of the perfectly stabilized output voltage, a TG Charger can be used as a power supply if batteries or large buffer capacitors are not available. Two outputs to charge 2 battery banks (24V models only) The TG Chargers feature 2 isolated outputs. The second output, limited to approximately 4A and with a slightly lower output voltage, is intended to top up a starter battery. To increase battery life: temperature compensation Every Skylla TG Charger comes with a battery temperature sensor. When connected, charge voltage will automatically decrease with increasing battery temperature. This feature is especially recommended for sealed batteries which otherwise might be overcharged and dry out due to venting. Battery voltage sense In order to compensate for voltage loss due to cable resistance, TG Chargers are provided with a voltage sense facility so that the battery always receives the correct charge voltage. Brand Victron Energy Manufacturer Part Number SDTG2401003 Voltage 24 Charger Current House Battery 100A Charger Current Starter Battery 4A Recommended Battery Capacity 500 – 1000Ah Battery Connection M8 Studs Outputs 1+1 Temperature Sensor Yes Can Be Used As Power Supply Yes IP Rating IP21 Dimensions H365 x W250 x D257mm Weight (kg) 10 Warranty 5 Years

Read more less