INVERTERS FOR SOLAR / BATTERY STORAGE

Adjustable output voltage: can also be used as a battery chargerFor example to charge a 12 Volt starter or accessory battery in an otherwise 24V system.  All models are short circuit proof and can be paralleled to increase output currentAn unlimited number of units can be connected in parallel.  IP43 protectionWhen installed with the screw terminals oriented downwards.  Screw terminalsNo special tools needed for installation. Input fuseOn 12V and 24V input models only. Brand Victron Energy Manufacturer Part Number ORI242410110R Input Voltage Range 16-35V Under Voltage Shutdown 14V Under Voltage Restart 15V Nominal Output Voltage 24.2V Output Voltage Adjust Range 20-30V Short Circuit Output Current 30A Cont. Output Power at 25°C 120W DC Connection Screw Terminals Protection Category IP43 Dimensions H100 x W113 x D47mm Weight (kg) 0.42 Warranty 5 Years

Read more less

For use in dual battery systems in vehicles or on boats where the (smart) alternator and the start battery are used to charge the service battery. The unit can be monitored and programmed via Bluetooth and can be remotely controlled via a remote on/off switch and has an engine running detection mechanism. The Orion Tr-Smart charger can be used in 12V or 24V systems and is suitable for both lead acid and lithium batteries. Models are available up to 400W and unlimited multiple units can be connected in parallel to increase output power. Suitable for high temperatures up to 55°C with a full rated output up to 40°C.   Features Bluetooth Smart enabled Any Bluetooth enabled smart phone, tablet or other device can be used to monitor, to change settings and to update the charger when new software features become available. Fully programmable Battery charge algorithm (configurable) or fixed output. Smart alternator compatibility: engine running detection mechanism. Adaptive 3-stage charge algorithm: bulk – absorption – float For lead acid batteries it is important that during shallow discharges the absorption time is kept short in order to prevent overcharging of the battery. After a deep discharge the absorption time is automatically increased to make sure that the battery is completely recharged.  For lithium batteries absorption time is fixed, default 2 hours. Alternatively, a fixed output voltage can be chosen. Remote on-off A remote on/off switch or relay contact can be connected to a two-pole connector. Alternatively, the H terminal (right) of the two-pole connector can be switched to battery plus, or the L terminal (left) of the two pole connector can be switched to battery minus (or the chassis of a vehicle, for example). All models are short circuit proof and can be paralleled to increase output current An unlimited number of units can be connected in parallel. High temperature protected The output current will reduce at high ambient temperature. IP43 protection When installed with the screw terminals oriented downwards. Screw terminals No special tools needed for installation. Input fuse (not replaceable) Brand Victron Energy Manufacturer Part Number ORI241236120 Warranty 5 Years Weight (kg) 1.6Kg Dimensions H130 x W186 x D70mm Input Voltage Range 20-35 V Protection Category IP43 Power Rating (W) 360 Nominal Output Voltage 12.2 V Output Voltage Adjust Range 10-15 V Short Circuit Output Current 60 A Cont. Output Power at 25°C 430 W Under Voltage Shutdown 14 V Under Voltage Restart 15 V

Read more less

For use in dual battery systems in vehicles or on boats where the (smart) alternator and the start battery are used to charge the service battery. The unit can be monitored and programmed via Bluetooth and can be remotely controlled via a remote on/off switch and has an engine running detection mechanism. The Orion Tr-Smart charger can be used in 12V or 24V systems and is suitable for both lead acid and lithium batteries. Models are available up to 400W and unlimited multiple units can be connected in parallel to increase output power. Suitable for high temperatures up to 55°C with a full rated output up to 40°C.   Features Bluetooth Smart enabled Any Bluetooth enabled smart phone, tablet or other device can be used to monitor, to change settings and to update the charger when new software features become available. Fully programmable Battery charge algorithm (configurable) or fixed output. Smart alternator compatibility: engine running detection mechanism. Adaptive 3-stage charge algorithm: bulk – absorption – float For lead acid batteries it is important that during shallow discharges the absorption time is kept short in order to prevent overcharging of the battery. After a deep discharge the absorption time is automatically increased to make sure that the battery is completely recharged.  For lithium batteries absorption time is fixed, default 2 hours. Alternatively, a fixed output voltage can be chosen. Remote on-off A remote on/off switch or relay contact can be connected to a two-pole connector. Alternatively, the H terminal (right) of the two-pole connector can be switched to battery plus, or the L terminal (left) of the two pole connector can be switched to battery minus (or the chassis of a vehicle, for example). All models are short circuit proof and can be paralleled to increase output current An unlimited number of units can be connected in parallel. High temperature protected The output current will reduce at high ambient temperature. IP43 protection When installed with the screw terminals oriented downwards. Screw terminals No special tools needed for installation. Input fuse (not replaceable) Brand Victron Energy Manufacturer Part Number ORI242440120 Warranty 5 Years Weight (kg) 1.6 Dimensions H130 x W186 x D70mm Input Voltage Range 20-35 V Protection Category IP43 Power Rating (W) 400 Nominal Output Voltage 24.2 V Output Voltage Adjust Range 20-30 V Short Circuit Output Current 40 A Cont. Output Power at 25°C 480 W Under Voltage Shutdown 14 V Under Voltage Restart 15 V DC Connection Screw Terminals

Read more less

Features Ultra-fast Maximum Power Point Tracking (MPPT) Especially in case of a clouded sky, when light intensity is changing continuously, an ultra-fast MPPT controller will improve energy harvest by up to 30 % compared to PWM charge controllers and by up to 10 % compared to slower MPPT controllers. Advanced Maximum Power Point Detection in case of partial shading conditions If partial shading occurs, two or more maximum power points may be present on the power-voltage curve. Conventional MPPTs tend to lock to a local MPP, which may not be the optimum MPP. The innovative BlueSolar algorithm will always maximize energy harvest by locking to the optimum MPP. Outstanding conversion efficiency No cooling fan. Maximum efficiency exceeds 98 %. Flexible charge algorithm Fully programmable charge algorithm, and eight pre-programmed algorithms, selectable with a rotary switch (see manual for details). Extensive electronic protection Over-temperature protection and power derating when temperature is high. PV short circuit and PV reverse polarity protection. PV reverse current protection. Internal temperature sensor and optional external battery voltage, temperature and current sensing via Bluetooth A Smart Battery Sense or a BMV-712 Smart Battery Monitor can be used to communicate battery voltage and temperature (and current, in case of a BMV-712 or a SmartShunt) to one or more BlueSolar Charge Controllers. (VE.Direct Bluetooth Smart dongle needed) Real-time data display options Color Control GX or other GX devices: see the Venus documents on our website. A smartphone or other Bluetooth-enabled device: VE.Direct Bluetooth Smart dongle needed. Brand Victron Energy Manufacturer Part Number SCC010060200 GTIN 8719076025474 Battery Voltage 12/24/48V Auto Select (software tool needed to select 36V) Rated Charge Current 60A Nominal PV Power, 12V 860W Nominal PV Power, 24V 1720W Max. PV Short Circuit Current 50A Maximum PV Open Circuit Voltage 150V absolute maximum coldest conditions 145V start-up and operating maximum Efficiency 98% Charge Algorithm Multi-stage adaptive Data Communication Port VE.Direct IP Rating IP43 (electronic components), IP22 (connection area) Dimensions H185 x W250 x D95mm Weight 3Kg Warranty 5 Years

Read more less

Features Ultra-fast Maximum Power Point Tracking (MPPT) Especially in case of a clouded sky, when light intensity is changing continuously, an ultra-fast MPPT controller will improve energy harvest by up to 30% compared to PWM charge controllers and by up to 10% compared to slower MPPT controllers. Advanced Maximum Power Point Detection in case of partial shading conditions If partial shading occurs, two or more maximum power points (MPP) may be present on the power-voltage curve. Conventional MPPTs tend to lock to a local MPP, which may not be the optimum MPP. The innovative BlueSolar algorithm will always maximize energy harvest by locking to the optimum MPP. Outstanding conversion efficiency No cooling fan. Maximum efficiency exceeds 99%. Flexible charge algorithm Fully programmable charge algorithm, and eight preprogrammed algorithms, selectable with a rotary switch (see manual for details). Extensive electronic protection Over-temperature protection and power derating when temperature is high. PV short circuit and PV reverse polarity protection. PV reverse current protection. Internal temperature sensor Compensates absorption and float charge voltage for temperature. Optional external battery voltage, temperature and current sensing via Bluetooth A Smart Battery Sense or a BMV-712 Smart Battery Monitor can be used to communicate battery voltage and temperature (and current, in case of a BMV 712 or a SmartShunt) to one or more BlueSolar Charge Controllers. (VE.Direct Bluetooth Smart dongle needed) VE.Can: the multiple controller solution Up to 25 units can be synchronised with VE.Can VE.Direct or VE.Can For a wired data connection to a Color Control GX, other GX products, PC or other devices Remote on-off To connect for example to a VE.BUS BMS. Programmable relay Can be programmed to trip on an alarm, or other events. Optional: SmartSolar pluggable LCD display Simply remove the rubber seal that protects the plug on the front of the controller, and plug-in the display.  CLICK HERE FOR SPEC SHEET Brand Victron Energy Manufacturer Part Number SCC125110441 GTIN 8719076050926 Battery Voltage 12/24/48V Auto Select (36V: manual) Rated Charge Current 100A Nominal PV Power, 12V 1450W Nominal PV Power, 24V 2900W Max. PV Short Circuit Current 70A Maximum PV Open Circuit Voltage 250V absolute maximum coldest conditions | 245V start-up and operating maximum Efficiency 99% Charge Algorithm multi-stage adaptive (eight preprogrammed algorithms) or user defined algorithm Data Communication Port VE.Can IP Rating IP43 (electronic components), IP22 (connection area) Dimensions H216 x W295 x D103mm Weight 4.5Kg Warranty 5 Years

Read more less

IP66 > 150% DC/AC ratio String current up to 16A Supports RS485 WiFi GPRS Supports export power control Intelligent redundant fan-cooling Natural convection Fan-less design Wide voltage range and low startup voltage Supports aluminium wire access to reduce cost AFCI protection proactively reduces fire risk Intelligent string monitoring smart I-V curve scan Natural convection Fan-less design longer lifespan Globally recognised branded componentry for longer life Supports high power modules for lower installation costs 3/4 MPPT design supports multiple orientation system design Night time PID recovery function increases overall system yield (optional) Scan to register on SolisCloud supports remote upgrade and control Supports GPRS/WiFi communication with less wiring and reduced installation costs Application       Commercial Manufacturer         Solis Phases         3 Phase Power Rating          kW40 Inverter Type           String Inverter Built in DC          Yes No. of MPPT          3 Built in Communication         Optional Commodity Code       85044086 Dimensions (mm) (H x W x D)       629 x 647 x 252

Read more less

It’s powerful enough to supply most common plug in appliances in your car, boat, caravan or home. A toroidal transformer provides a high peak power surge capacity, stable voltage, frequency and high quality sine-wave. Installation is simpler than ever before with terminals now more accessible for the installer, enabling a more professional finish. Bluetooth is built-in, and makes setting up your high power inverter easier than ever before.Configure alarms, alarm relay, voltage cut-off, output voltage, frequency, eco-mode and more, all from within VictronConnect. Features of the Phoenix 24/2000 Smart Bluetooth built-in: fully configurable with a tablet or smartphone Low battery voltage alarm Low battery voltage cut-off and restart levels Dynamic cut-off: load dependent cut-off level Output voltage: 210 – 245V Frequency: 50 Hz or 60 Hz ECO mode on/off and ECO mode sense level Alarm relay Monitoring: In- and output voltage, load and alarms  VE.Direct communication port The VE.Direct port can be connected to a computer (VE.Direct to USB interface cable needed) to configure and monitor the same parameters Proven reliability The full bridge plus toroidal transformer topology has proven its reliability over many years. The inverters are short circuit proof and protected against overheating, whether due to overload or high ambient temperature. High start-up power Needed to start loads such as power converters for LED lamps, halogen lamps or electric tools. ECO mode When in ECO mode, the inverter will switch to standby when the load decreases below a preset value (min load: 15W). Once in standby the inverter will switch on for a short period (adjustable, default: every 2,5 seconds). If the load exceeds a preset level, the inverter will remain on. Remote on/off A remote on/off switch or relay contact can be connected to a two pole connector. Alternatively, the H terminal (left) of the two pole connector can be switched to battery plus, or the L terminal (right) of the two pole connector can be switched to battery minus (or the chassis of a vehicle, for example). To transfer the load to another AC source: the automatic transfer switch   For our low power inverters we recommend our Filax Automatic Transfer Switch. The Filax features a very short switchover time (less than 20 milliseconds) so that computers and other electronic equipment will continue to operate without disruption. Alternatively use a MultiPlus with built-in transfer switch.   Control over system Want to have perfect control over your system from wherever you are whilst using your Phoenix Inverter 24/1600 Smart, why not have a look at the CerboGX. Simply connect through the Victron Remote Management (VRM) portal, or access directly, using the separate GX Touch, a MFD or the VictronConnect App thanks to its added Bluetooth capability. This latest addition to the GX-range combines all the best of connectivity, redefining smart power solutions in every way. Brand Victron Energy Manufacturer Part Number PIN242201000 gtin 8719076057536 Voltage 24V Cont. Output Power at 25ºC 2000VA Peak Power 4000W Output AC Voltage 230V Efficiency 94% Protection Category IP21 Dimensions H485 x W219 x D125mm Weight 13Kg Warranty 5 Years Bluetooth Enabled Yes Country of Manufacture China

Read more less

Features of the Phoenix 48/2000 Smart Bluetooth built-in: fully configurable with a tablet or smartphone Low battery voltage alarm Low battery voltage cut-off and restart levels Dynamic cut-off: load dependent cut-off level Output voltage: 210 – 245V Frequency: 50 Hz or 60 Hz ECO mode on/off and ECO mode sense level Alarm relay Monitoring: In- and output voltage, load and alarms VE.Direct communication port The VE.Direct port can be connected to a computer (VE.Direct to USB interface cable needed) to configure and monitor the same parameters. Proven reliability The full bridge plus toroidal transformer topology has proven its reliability over many years. The inverters are short circuit proof and protected against overheating, whether due to overload or high ambient temperature. High start-up power Needed to start loads such as power converters for LED lamps, halogen lamps or electric tools. ECO mode When in ECO mode, the inverter will switch to standby when the load decreases below a preset value. Once in standby the inverter will switch on for a short period every 2,5 seconds (adjustable). If the load exceeds the preset level, the inverter will remain on. Remote on/off A remote on/off switch or relay contact can be connected to a two pole connector. Alternatively, the H terminal (left) of the two pole connector can be switched to battery plus, or the L terminal (right) of the two pole connector can be switched to battery minus (or the chassis of a vehicle, for example). To transfer the load to another AC source: the automatic transfer switch For our low power inverters we recommend our Filax Automatic Transfer Switch. The Filax features a very short switchover time (less than 20 milliseconds) so that computers and other electronic equipment will continue to operate without disruption. Alternatively use a MultiPlus with built-in transfer switch Brand Victron Energy Manufacturer Part Number PIN482201000 gtin 8719076057550 Voltage 48V Cont. Output Power at 25°C 2000VA Peak Power 4000W Output AC Voltage 230V Efficiency 94% Protection Category IP21 Dimensions H485 x W219 x D125mm Weight 13Kg Warranty 5 Years Bluetooth Enabled Yes Country of Manufacture China

Read more less

The inverter is equipped with a display to read out battery, inverter, and solar charger details. These parameters can also be read out via Bluetooth by the VictronConnect app. In addition to this, the inverter has a VE.Can Port for connection to a GX device for system monitoring; and VE.Direct port for connection to a GlobalLink 520.   Features Off-Grid solar inverter The Inverter RS Smart Solar 48/6000 is a 48V 6kVA Inverter with 450VDC 4kWp PV input. It is used in off-grid solar applications where AC power is required. Combination of an inverter, bi-directional DC-DC converter and MPPT The inverter produces a perfect sine wave, able to supply high powered appliances. It is supplied by a bi-directional DC-DC converter, that can either charge the battery when excess solar power is available or convert from the battery when it is needed. Wide MPPT voltage range 80 – 450VDC, with a 120VDC PV startup voltage. Light weight, efficient and quiet Thanks to high frequency technology and a new design this powerful inverter weighs only 11kg. In addition to this it has an excellent efficiency, low standby power, and a very quiet operation. Display and Bluetooth The display reads battery, inverter and solar charge controller parameters. The same parameters can be accessed with a smartphone or other Bluetooth enabled device. In addition, Bluetooth can be used to set up the system and to change settings with VictronConnect. VE.Can and VE.Direct port For connection to a GX device for system monitoring, data logging, and remote firmware updates. Built in PV isolator Both parallel PV strings connected to the MC4 plugs can be safely isolated with the large built-in switch on the bottom of the unit. I/O Connections Programmable Relay, temperature sensor and voltage sensor connections. The remote input can also be configured to accept the Victron smallBMS. Brand Victron Energy Manufacturer Part Number PIN482601000 GTIN 8719076048176 DC Input voltage range 38-64V Continuous Output Power at 25°C Increases linearly from 4800W at 46VDC to 5300W at 52VDC Continuous output power at 40°C 4500W Peak power 9kW for 3 seconds Zero load power 20W Maximum DC voltage 450V Nominal DC voltage 300V Start-up voltage 120V MPPT operating voltage range 80-450V Charge voltage absorption (V DC) 57.6V Charge voltage float (V DC) 55.2V Maximum charge current 100A Battery Temperature Sensor Yes Parallel and 3-phase operation No Programmable Relay Yes Data Communications Ports VE.Direct port and VE.Can port Remote on-off Yes Protection Category IP22 Battery-Connection M8 Bolts Dimensions H425 x W440 x D125mm Weight 11Kg Warranty 5 Years

Read more less

Features of the Quattro 48/5000-70-100 Two AC Inputs & two AC Outputs The Quattro can be connected to two independent AC sources, for example shore-side power and a generator, or two generators. The Quattro will automatically connect to the active source. The main output has no-break functionality. In the event of a grid failure, or shore or generator power being disconnected, the Quattro takes over the supply to the connected loads. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption. The second output is live only when AC is available on one of the inputs of the Quattro. Loads that should not discharge the battery, such as air-conditioning or a water heater can be connected to this output.   Unique PowerAssist feature The Quattro will prevent overload of a limited AC source, such as a generator or shore power connection. First, battery charging will automatically be reduced when otherwise an overload would occur. The second level will boost the output of a generator or shore side supply with power taken from the battery.   Virtually unlimited power thanks to parallel operation Up to 6 Quattros can operate in parallel to achieve higher power output. Three phase or split phase operation is also possible. Please check our datasheets to see which models have paralleling, three phase and split phase capabilities.   Remote Monitoring and Control When coupled with a GX device (e.g. Cerbo GX) you can monitor and control your Quattro and system or systems’ locally (LAN) or remotely via the internet from anywhere in the world, using the free VRM app and free VRM portal website. Access can be from a phone, tablet, laptop or PC for multiple operating systems. There is no end to the level of control, from adjusting your Quattro to auto starting a backupgenerator and more…   Want to have perfect control over your system from wherever you are whilst using your Quattro 48/5000, why not have a look at the Cerbo GX. Simply connect through the Victron Remote Management (VRM) portal, or access directly, using the separate GX Touch, a MFD or the VictronConnect App thanks to its added Bluetooth capability. This latest addition to the GX-range combines all the best of connectivity, redefining smart power solutions in every way.   Watch the new video that explains all there is to know about installing the new Cerbo GX & GX Touch 50   The MK3-USB allows the Quattro to connect to a computer for configuration and firmware updates.

Read more less

Features Control Your Charger Remotely The MPPT VE.Can SmartSolar charger can be remotely controlled and configured over Bluetooth via the VictronConnect App. This allows device set-up, management, and at-a-glance information, such as battery voltage and current, PV voltage and current, and historical data.  Daisy Chain Additional Units The VE.Can SmartSolar charger is equipped with CAN bus ports. This allows for communication with additional VE.Can SmartSolar chargers. The additional units are simply “daisy chained” to each other with a single RJ45 cable between the individual units. When connected to each other, all individual VE.Can SmartSolar chargers, will synchronise their charge stages. They can also send their data, via a single cable, to a GX monitoring device.  Remote Monitoring and Control If the GX device is connected to the internet, the Victron Remote Management Portal (VRM) provides access to the full power of your solar charger(s). For remote installations – even when there is no internet connection nearby – you may be able to monitor your MPPT by connecting the GlobalLink 520. Ultra-fast Maximum Power Point Tracking (MPPT) Especially in case of a clouded sky, when light intensity is changing continuously, an ultra-fast MPPT controller will improve energy harvest by up to 30% compared to PWM charge controllers and by up to 10% compared to slower MPPT controllers. Advanced Maximum Power Point Detection in case of partial shading conditions If partial shading occurs, two or more maximum power points (MPP) may be present on the powervoltage curve. Conventional MPPTs tend to lock to a local MPP, which may not be the optimum MPP. The innovative SmartSolar algorithm will always maximize energy harvest by locking to the optimum MPP. Outstanding conversion efficiency No cooling fan. Maximum efficiency exceeds 98%. Flexible charge algorithm Fully programmable charge algorithm, and eight pre-programmed algorithms, selectable with a rotary switch (see manual for details). Extensive electronic protection Over-temperature protection and power derating when temperature is high. PV short circuit and PV reverse polarity protection. PV reverse current protection. Bluetooth Smart built-in The wireless solution to set-up, monitor, update and synchronise SmartSolar Charge Controllers. Internal temperature sensor and optional external battery voltage, temperature and current sensing via Bluetooth A Smart Battery Sense, a BMV-712 Smart Battery Monitor or a SmartShunt can be used to communicate battery voltage and temperature (and current, in case of a BMV 712 or a SmartShunt) to one or more SmartSolar Charge Controllers. VE.Direct or VE.Can For a wired data connection to a Color Control GX, other GX products, PC or other devices Fully discharged battery recovery function Will initiate charging even if the battery has been discharged to zero volts. Will reconnect to a fully discharged Li-ion battery with integrated disconnect function. VE.Can: the multiple controller solution Up to 25 units can be synchronised with VE.Can, and up to 10 units with Bluetooth Remote on-off To connect for example to a VE.BUS BMS. Programmable relay Can be programmed to trip on an alarm, or other events. Optional: SmartSolar pluggable LCD display Simply remove the rubber seal that protects the plug on the front of the controller, and plug-in the display. Brand Victron Energy Manufacturer Part Number SCC125110512 GTIN 8719076055679 Voltage 12/24/48V Rated Charge Current 100A Nominal PV Power, 12V 1450W Max. PV Short Circuit Current 70A (max 30A per MC4 conn.) Max. PV Open Circuit Voltage 250V absolute maximum coldest conditions 245V start-up and operating maximum Protection Category IP43 (electronic components), IP22 (connection area) Efficiency 99% Bluetooth Enabled Yes Dimensions H246 x W295 x D103mm Weight 4.5Kg Warranty 5 Years

Read more less

Brand Victron Energy Manufacturer Part Number SCA000300000 Warranty 5 Years

Read more less

Brand Victron Energy Manufacturer Part Number CIP133060010 Warranty 5 Years Appr. Voltage Drop 70 mV Cold Resistance 0.9    

Read more less

The right amount of charge for a lead-acid battery: variable absorption time BatterySafe mode: preventing damage due to excessive gassing Storage mode: less maintenance and aging when the battery is not in use Smaller and lighter compared to similar models NMEA2000 Canbus connection PowerControl: set a maximum shore power Remote Control Li-ion (LiFePo4) ready   Features Rugged Aluminium epoxy powder coated cases with drip shield and stainless steel fixings withstand the rigors of an adverse environment: heat, humidity and salt air. Circuit boards are protected with an acrylic coating for maximum corrosion resistance. Temperature sensors ensure that power components will always operate within specified limits, if needed by automatic reduction of output current under extreme environmental conditions. Flexible Next to a CAN bus (NMEA2000) interface, a rotary switch, DIP switches and potentiometers are available to adapt the charge algorithm to a particular battery and its conditions of use. Please refer to the manual for a complete overview of the possibilities. Synchronised parallel operation Several chargers can be synchronised with the CAN bus interface. This is achieved by simply interconnecting the chargers with RJ45 UTP-cables. Please see the manual for details. The right amount of charge for a lead-acid battery: variable absorption time When only shallow discharges occur the absorption time is kept short in order to prevent overcharging of the battery. After a deep discharge the absorption time is automatically increased to make sure that the battery is completely recharged. Preventing damage due to excessive gassing: the BatterySafe mode If, in order to quickly charge a battery, a high charge current in combination with a high absorption voltage has been chosen, the Skylla-i will prevent damage due to excessive gassing by automatically limiting the rate of voltage increase once the gassing voltage has been reached. Less maintenance and aging when the battery is not in use: the Storage mode The storage mode kicks in whenever the battery has not been subjected to discharge during 24 hours. In the storage mode float voltage is reduced to 2,2 V/cell (26,4 V for 24 V battery) to minimise gassing and corrosion of the positive plates. Once a week the voltage is raised back to the absorption level to ‘refresh’ the battery. This feature prevents stratification of the electrolyte and sulphation, a major cause of early battery failure. To increase battery life: temperature compensation Every Skylla-i comes with a battery temperature sensor. When connected, charge voltage will automatically decrease with increasing battery temperature. This feature is especially recommended for sealed lead-acid batteries and/or when important fluctuations of battery temperature are expected. Battery voltage sense In order to compensate for voltage loss due to cable resistance, the Skylla-i is provided with a voltage sense facility so that the battery always receives the correct charge voltage. Suitable for AC and DC supply (AC-DC and DC-DC operation) The chargers also accept a DC supply. Use as a power supply As a result of the perfectly stabilized output voltage, the Skylla-i can be used as a power supply if batteries or large buffer capacitors are not available. Li-Ion (LiFePO4) ready Simple charger on-off control can be implemented by connecting a relay or open collector optocoupler output from a Li-Ion BMS to the remote control port of the charger. Alternatively complete control of voltage and current can be achieved by connecting to the galvanically isolated CAN bus port. Brand Victron Energy Manufacturer Part Number SKI024100002 Voltage 24 Charger Current House Battery 3 x 100A Charger Current Starter Battery N.A. Recommended Battery Capacity 500 – 1000Ah Battery Connection M8 Bolts Outputs 3 Temperature Sensor Yes Can Be Used As Power Supply Yes IP Rating IP21 Dimensions H405 x W250 x D150mm Weight (kg) 7 Warranty 5 Years

Read more less

Brand Victron Energy Manufacturer Part Number SCC010005050 GTIN 8719076046172 Battery Voltage 12/24 V automatic system voltage detection Rated Charge Current 5A Maximum Solar Voltage 28V / 55V Load Output Manual control + low voltage disconnect + timer Grounding Common positive IP Rating IP20 Dimensions H96 x W169 x D36mm Weight 0.15Kg Warranty 5 Years

Read more less

Solis Mini Series Inverter Leading Features:• Max. efficiency 97.3%• Compact and lightweight• String current up to 14A• Super high frequency switching technology• Wide voltage range and low startup voltage• Precise MPPT algorithm• Intergrated Export Power Manager (EPM)• Integrated AFCI (DC arc-fault circuit protection)• Friendly and adaptable connection to the grid Manufacturer       Solis Phases         1 Phase Power Rating         kW0.7 Inverter Type           String Inverter Built in DC           Yes No. of MPPT           1 Built in Communication          Optional Commodity Code         85044085 Dimensions (mm) (H x W x D)373 x 310 x 160

Read more less

Additional features:  A total of 15x inverters can be connected in a three-phase configuration (five units per phase) - giving a maximum power output of 240kW  Three inverters can be connected in a single-phase configuration giving a total power of 48kW  Contains 3x MPPTs to allow for flexible PV array designs and improved efficiency  Programmable multiple operation modes: on-grid/off-grid & UPS  IP65 protection rating  Wi-Fi dongle as standard – enabling remote monitoring via the Sunsynk cloud  Compatible with leading lithium battery brands such as Hubble Lithium, Pylontech LV, Freedomwon and Kodak (BL3.6)  Sunsynk inverter and Freedom Won battery pairing : 10-year extended warranty. For installations with Pylontech, REVOV and Hubble Lithium batteries use this BMS cable For installations with Freedom Won batteries use this BMS cable Installations with Sunsynk products need to be registered to gain full activation of the warranty. Equipment warranty registration needs to take place within 7 (seven) days of commissioning of the project, failure to register the warranty may result in the warranty being made void.   Supplier Part No: SUNSYNK-16K-SG01LP1 Weight: 56 kg Rated Power: 16,000 W Min PPT Voltage: 250 V Max PPT Voltage: 450 V DC Startup Voltage: 150 V DC Shutdown Voltage: 0 V Max Input Voltage: 450 V Max DC Power: 18,000 W Max AC Power (5 Minutes): 16,001 W Surge AC Power (1 Second): 32,000 W Max DC Current: 66 A Max DC Inputs: 6 Has DC Fuses: 0 Connector: Screw Terminal   Included Connectors: 12 Euro Efficiency: 97.6 % Transformer: None MPPT Quantity : 3 Has Integrated DC Switch: Yes Warranty: 5 years

Read more less

Features Uninterrupted AC power (UPS function) In the event of a grid failure, or when shore or generator power is disconnected, the inverter within the Multi is automatically activated and takes over the supply to the connected loads. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption Remote Monitoring and Control Monitor and control your MultiPlus and system or systems’ locally (LAN) or remotely via the internet from anywhere in the world, using the free VRM app and free VRM portal website. Access can be from a phone, tablet, laptop or PC for multiple operating systems. There is no end to the level of control, via the required Color Control GX or Venus GX, from adjusting your MultiPlus to setting a Geofence for hire vehicles and more… Proven reliability The full bridge plus toroidal transformer topology has proven its reliability over many years. The inverter is short circuit proof and protected against overheating, whether due to overload or high ambient temperature.  PowerControl – Dealing with limited generator, shore side or grid power With the Multi Control Panel a maximum generator or shore current can be set. The MultiPlus will then take account of other AC loads and use whatever is extra for charging, thus preventing the generator or shore supply from being overloaded. PowerAssist – Boosting the capacity of shore or generator power Where peak power is so often required only for a limited period, the MultiPlus will make sure that insufficient shore or generator power is immediately compensated for by power from the battery. When the load reduces, the spare power is used to recharge the battery. High start-up power Needed to start high inrush loads such as power converters for LED lamps, halogen lamps or electric tools Programmable relay By default, the programmable relay is set as an alarm relay, i.e. the relay will de-energise in the event of an alarm or a pre-alarm (inverter almost too hot, ripple on the input almost too high, battery voltage almost too low).   Brand Victron Energy Manufacturer Part Number PMP121800000 Voltage 12 Transfer Switch (A) 16 Cont. Output Power at 25°C (VA) 800 Peak Power (W) 1600 Max Efficiency 92% Zero Load Power (W) 7 Charge Current House Battery (A) 35 Charge Current Starter Battery (A) 1 (12V and 24V models only) Battery Temperature Sensor Yes Programmable Relay Yes Remote on-off Yes Protection Category IP21 Dimensions H360 x W240 x D100mm Weight (kg) 6.4 Warranty 5 Years Country of Manufacture India

Read more less

Features Unique PowerAssist feature The Quattro will prevent overload of a limited AC source, such as a generator or shore power connection. First, battery charging will automatically be reduced when otherwise an overload would occur. The second level will boost the output of a generator or shore side supply with power taken from the battery. Virtually unlimited power thanks to parallel operation Up to 6 Quattros can operate in parallel to achieve higher power output. Three phase or split phase operation is also possible. Please check our datasheets to see which models have paralleling, three phase and split phase capabilities. Remote Monitoring and Control Monitor and control your Quattro and system or systems’ locally (LAN) or remotely via the internet from anywhere in the world, using the free VRM app. Access can be from a phone, tablet, laptop or PC for multiple operating systems. There is no end to the level of control, via the required Color Control GX or Venus GX, from adjusting your Quattro to setting a Geofence for hire vehicles and more… Split phase and three phase capability Two units can be configured for split phase, and three units can be configured for three phase output. But that’s not all: up to 6 sets of three units can be parallel connected to provide 144kW / 180kVA inverter power and more than 2500A charging capacity. For more detail please enter parallel in the search box on our website. Solar energy: AC power available even during a grid failure The Quattro can be used in off grid as well as grid connected PV and other alternative energy systems. Loss of mains detection software is available. System configuring In case of a stand-alone application, if settings have to be changed, this can be done in a matter of minutes with a DIP switch setting procedure. Parallel and three phase applications can be configured with VE.Bus Quick Configure and VE.Bus System Configurator software. Off grid, grid interactive and self-consumption applications, involving grid-tie inverters and/or MPPT Solar Chargers can be configured with Assistants (dedicated software for specific applications). Brand Victron Energy Manufacturer Part Number QUA248020010 Voltage 24 Transfer Switch (A) Yes Cont. Output Power at 25°C (VA) 8000 Peak Power (W) 16000 Max Efficiency 94% Zero Load Power (W) 60 Charge Current House Battery (A) 26.4 Charge Current Starter Battery (A) 4 (12V and 24V models only) Battery Temperature Sensor Yes Programmable Relay 3x Remote on-off Yes Protection Category IP21 Dimensions H470 x W350 x D280mm Weight (kg) 45 Warranty 5 Years Country of Manufacture India

Read more less

Features Control Your Charger Remotely The MPPT VE.Can SmartSolar charger can be remotely controlled and configured over Bluetooth via the VictronConnect App. This allows device set-up, management, and at-a-glance information, such as battery voltage and current, PV voltage and current, and historical data.  Daisy Chain Additional Units The VE.Can SmartSolar charger is equipped with CAN bus ports. This allows for communication with additional VE.Can SmartSolar chargers. The additional units are simply “daisy chained” to each other with a single RJ45 cable between the individual units. When connected to each other, all individual VE.Can SmartSolar chargers, will synchronise their charge stages. They can also send their data, via a single cable, to a GX monitoring device.  Remote Monitoring and Control If the GX device is connected to the internet, the Victron Remote Management Portal (VRM) provides access to the full power of your solar charger(s). For remote installations – even when there is no internet connection nearby – you may be able to monitor your MPPT by connecting the GlobalLink 520. Ultra-fast Maximum Power Point Tracking (MPPT) Especially in case of a clouded sky, when light intensity is changing continuously, an ultra-fast MPPT controller will improve energy harvest by up to 30% compared to PWM charge controllers and by up to 10% compared to slower MPPT controllers. Advanced Maximum Power Point Detection in case of partial shading conditions If partial shading occurs, two or more maximum power points (MPP) may be present on the powervoltage curve. Conventional MPPTs tend to lock to a local MPP, which may not be the optimum MPP. The innovative SmartSolar algorithm will always maximize energy harvest by locking to the optimum MPP. Outstanding conversion efficiency No cooling fan. Maximum efficiency exceeds 98%. Flexible charge algorithm Fully programmable charge algorithm, and eight pre-programmed algorithms, selectable with a rotary switch (see manual for details). Extensive electronic protection Over-temperature protection and power derating when temperature is high. PV short circuit and PV reverse polarity protection. PV reverse current protection. Bluetooth Smart built-in The wireless solution to set-up, monitor, update and synchronise SmartSolar Charge Controllers. Internal temperature sensor and optional external battery voltage, temperature and current sensing via Bluetooth A Smart Battery Sense, a BMV-712 Smart Battery Monitor or a SmartShunt can be used to communicate battery voltage and temperature (and current, in case of a BMV 712 or a SmartShunt) to one or more SmartSolar Charge Controllers. VE.Direct or VE.Can For a wired data connection to a Color Control GX, other GX products, PC or other devices Fully discharged battery recovery function Will initiate charging even if the battery has been discharged to zero volts. Will reconnect to a fully discharged Li-ion battery with integrated disconnect function. VE.Can: the multiple controller solution Up to 25 units can be synchronised with VE.Can, and up to 10 units with Bluetooth Remote on-off To connect for example to a VE.BUS BMS. Programmable relay Can be programmed to trip on an alarm, or other events. Optional: SmartSolar pluggable LCD display Simply remove the rubber seal that protects the plug on the front of the controller, and plug-in the display. Brand Victron Energy Manufacturer Part Number SCC125070421 GTIN 8719076051213 Battery Voltage 12/24/48V Auto Select (36V: manual) Rated charge current 70A Nominal PV power, 12V 1000W Nominal PV power, 24V 2000W Max. PV Short Circuit Current 35A Maximum PV Open Circuit Voltage 250V absolute maximum coldest conditions, 245V start-up and operating maximum Efficiency 99% Charge Algorithm multi-stage adaptive (eight preprogrammed algorithms) or user defined algorithm Data Communication Port VE.Can, VE.Direct and Bluetooth Dimensions H185 x W250 x D95mm Weight 3Kg Warranty 5 Years

Read more less

Features Control Your Charger Remotely The MPPT VE.Can SmartSolar charger can be remotely controlled and configured over Bluetooth via the VictronConnect App. This allows device set-up, management, and at-a-glance information, such as battery voltage and current, PV voltage and current, and historical data.  Daisy Chain Additional Units The VE.Can SmartSolar charger is equipped with CAN bus ports. This allows for communication with additional VE.Can SmartSolar chargers. The additional units are simply “daisy chained” to each other with a single RJ45 cable between the individual units. When connected to each other, all individual VE.Can SmartSolar chargers, will synchronise their charge stages. They can also send their data, via a single cable, to a GX monitoring device.  Remote Monitoring and Control If the GX device is connected to the internet, the Victron Remote Management Portal (VRM) provides access to the full power of your solar charger(s). For remote installations – even when there is no internet connection nearby – you may be able to monitor your MPPT by connecting the GlobalLink 520. Ultra-fast Maximum Power Point Tracking (MPPT) Especially in case of a clouded sky, when light intensity is changing continuously, an ultra-fast MPPT controller will improve energy harvest by up to 30% compared to PWM charge controllers and by up to 10% compared to slower MPPT controllers. Advanced Maximum Power Point Detection in case of partial shading conditions If partial shading occurs, two or more maximum power points (MPP) may be present on the powervoltage curve. Conventional MPPTs tend to lock to a local MPP, which may not be the optimum MPP. The innovative SmartSolar algorithm will always maximize energy harvest by locking to the optimum MPP. Outstanding conversion efficiency No cooling fan. Maximum efficiency exceeds 98%. Flexible charge algorithm Fully programmable charge algorithm, and eight pre-programmed algorithms, selectable with a rotary switch (see manual for details). Extensive electronic protection Over-temperature protection and power derating when temperature is high. PV short circuit and PV reverse polarity protection. PV reverse current protection. Bluetooth Smart built-in The wireless solution to set-up, monitor, update and synchronise SmartSolar Charge Controllers. Internal temperature sensor and optional external battery voltage, temperature and current sensing via Bluetooth A Smart Battery Sense, a BMV-712 Smart Battery Monitor or a SmartShunt can be used to communicate battery voltage and temperature (and current, in case of a BMV 712 or a SmartShunt) to one or more SmartSolar Charge Controllers. VE.Direct or VE.Can For a wired data connection to a Color Control GX, other GX products, PC or other devices Fully discharged battery recovery function Will initiate charging even if the battery has been discharged to zero volts. Will reconnect to a fully discharged Li-ion battery with integrated disconnect function. VE.Can: the multiple controller solution Up to 25 units can be synchronised with VE.Can, and up to 10 units with Bluetooth Remote on-off To connect for example to a VE.BUS BMS. Programmable relay Can be programmed to trip on an alarm, or other events. Optional: SmartSolar pluggable LCD display Simply remove the rubber seal that protects the plug on the front of the controller, and plug-in the display. Brand Victron Energy Manufacturer Part Number SCC125085511 Battery Voltage 12 / 24 / 48V Auto Select (36V: manual) Rated Charge Current 85A Nominal PV Power, 12V 1200W Nominal PV Power, 24V 2400W Max. PV Short Circuit Current 70A (max 30A per MC4 conn.) Maximum PV Open Circuit Voltage 250V absolute maximum coldest conditions, 245V start-up and operating maximum Efficiency 99% Charge Algorithm multi-stage adaptive (eight preprogrammed algorithms) or user defined algorithm Data Communication Port VE.Can, VE.Direct and Bluetooth IP Rating IP43 (electronic components), IP22 (connection area) Dimensions H216 x W295 x D103mm Weight 4.5Kg Warranty 5 Years

Read more less

Brand Victron Energy Manufacturer Part Number SCA000500100 Warranty 5 Years

Read more less

Brand Victron Energy Manufacturer Part Number SCA001000100 Warranty 5 Years

Read more less

Brand Victron Energy Manufacturer Part Number SHU500050100 Warranty 5 Years

Read more less

  Brand Victron Energy Manufacturer Part Number CIP136200010 Warranty 5 Years Appr. Voltage Drop 80 mV Cold Resistance 0.25  

Read more less

Remote on-off The remote on-off eliminates the need for a high current switch in the input wiring. The remote on-off can be operated with a low power switch or by for example the engine run/stop switch (see manual).  Adjustable output voltage: can also be used as a battery chargerFor example to charge a 12 Volt starter or accessory battery in an otherwise 24V system.  All models are short circuit proof and can be paralleled to increase output currentAn unlimited number of units can be connected in parallel.  IP43 protectionWhen installed with the screw terminals oriented downwards.  Screw terminalsNo special tools needed for installation. Input fuseOn 12V and 24V input models only.  PLEASE CLICK HERE FOR SPEC SHEET Brand Victron Energy Manufacturer Part Number ORI241210110R Input Voltage Range 16-35V Under Voltage Shutdown 14V Under Voltage Restart 15V Nominal Output Voltage 12.2V Output Voltage Adjust Range 10-15V Short Circuit Output Current 39A Cont. Output Power at 25°C 110W DC Connection Screw Terminals Protection Category IP43 Dimensions H100 x W113 x D47mm Weight (kg) 0.42 Warranty 5 Years

Read more less

Adjustable output voltage: can also be used as a battery chargerFor example to charge a 12 Volt starter or accessory battery in an otherwise 24V system.  All models are short circuit proof and can be paralleled to increase output currentAn unlimited number of units can be connected in parallel.  IP43 protectionWhen installed with the screw terminals oriented downwards.  Screw terminalsNo special tools needed for installation. Input fuseOn 12V and 24V input models only. Brand Victron Energy Manufacturer Part Number ORI484828110 Input Voltage Range 32-70V Under Voltage Shutdown 28V Under Voltage Restart 30V Nominal Output Voltage 48.2V Output Voltage Adjust Range 40-60V Short Circuit Output Current 25A Cont. Output Power at 25°C 320W DC Connection Screw Terminals Protection Category IP43 Dimensions H130 x W186 x D70 mm Weight (kg) 1.3 Warranty 5 Years

Read more less

Liquid crystal display For status monitoring and set-up Day/night timing of the load output This option allows for a pre-set ON-time after dusk. Programmable battery charge algorithm Preprogrammed algorithms for AGM, GEL, Flooded or LiFePO4 batteries (with internal BMS only) Two 5 Volt USB outputs Maximum current (both outputs combined): 2A Brand Victron Energy Manufacturer Part Number SCC010030050 GTIN 8719076046226 Battery Voltage 12/24 V automatic system voltage detection Rated Charge Current 30A Maximum Solar Voltage 28V / 55V Load Output Manual control + low voltage disconnect + timer Grounding Common positive IP Rating IP20 Dimensions H101 x W184 x D47mm Weight 0.3Kg Warranty 5 Years

Read more less

MPPT: Ultra Fast Maximum Power Point Tracking By constantly monitoring the voltage and current output of your solar (PV) panels, MPPT technology ensures that every drop of available power is rinsed out of your panels, and harvested for storage. The advantage of this is most noticeable when the sky is partially clouded, and light intensity is constantly changing. Remote Monitoring and Control Remotely control and monitor the extensive features of your BlueSolar MPPT charger by attaching a bluetooth dongle and pairing it with your smartphone or other device via VictronConnect. If your installation is connected to the internet Victron Remote Management Portal (VRM) provides access to the full power of your MPPT, anytime, anywhere; both services are free to use. For remote installations – even when there is no internet connection or phone signal nearby – you may be able to monitor your MPPT by bluetooth-pairing with a LoRaWAN (long-range wide area network) device, available optionally. Advanced Maximum Power Point Detection in case of partial shading conditions If partial shading occurs, two or more maximum power points may be present on the power-voltage curve. Conventional MPPTs tend to lock to a local MPP, which may not be the optimum MPP. The innovative BlueSolar algorithm will always maximize energy harvest by locking to the optimum MPP. Outstanding conversion efficiency No cooling fan. Maximum efficiency exceeds 98%. Full output current up to 40°C (104°F). Flexible charge algorithm Fully programmable charge algorithm (see the software page on our website), and eight preprogrammed algorithms, selectable with a rotary switch (see manual for details). Extensive electronic protection Over-temperature protection and power derating when temperature is high. PV short circuit and PV reverse polarity protection. PV reverse current protection. Internal temperature sensor Compensates absorption and float charge voltage for temperature. Real-time data display options Color Control GX or other GX devices: see the Venus documents on our website. A smartphone or other Bluetooth-enabled device: VE.Direct Bluetooth Smart dongle needed. Brand Victron Energy Manufacturer Part Number SCC115045222 GTIN 8719076053033 Battery Voltage 12/24/48V Auto Select (software tool needed to select 36V) Rated Charge Current 45A Nominal PV power 12V: 650W / 24V: 1300W / 36V: 1950W / 48V: 2600W Max. PV short circuit current 50A Maximum PV Open Circuit Voltage 150V absolute maximum coldest conditions 145V start-up and operating maximum Maximum efficiency 98% Charge Algorithm multi-stage adaptive (eight pre-programmed algorithms) Data Communication Port VE.Direct Protection Category IP43 (electronic components), IP22 (connection area) Dimensions H130 x W186 x D70mm Weight 1.25Kg Warranty 5 Years

Read more less

The Fox system is easy to install and will save you time spent on installation. Remote monitoring is also avalible via your smartphone or web portal. Uses high voltage batteries  IP65 rated - suitable for outdoor installations Remote monitoring via web portal or smartphone Easy to expand battery capacity Dual MPPT - ensure optimal solar production High round-trip efficiency of 97% CT Clamps, meter and WiFi stick are included in the box Please Note: When installing batteries side-by-side and not stacked one on top of the other, we recommend using    Weight: 26.7 kg Rated Power: 3,000 W Min PPT Voltage: 80 V Max PPT Voltage: 550 V DC Startup Voltage: 75 V DC Shutdown Voltage: 75 V Max Input Voltage: 600 V Max DC Power: 4,680 W Max AC Power (5 Minutes): 5,000 W Surge AC Power (1 Second): 6,000 W Max DC Current: 27 A Max DC Inputs: 2 Has DC Fuses: 0 Connector: MC4   Included Connectors: 4 Euro Efficiency: 97 % Transformer: None MPPT Quantity : 2 Has Integrated DC Switch: Yes Warranty: 5 years

Read more less

Features Uninterrupted AC power (UPS function) In the event of a grid failure, or when shore or generator power is disconnected, the inverter within the Multi is automatically activated and takes over the supply to the connected loads. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption Remote Monitoring and Control Monitor and control your MultiPlus and system or systems’ locally (LAN) or remotely via the internet from anywhere in the world, using the free VRM app and free VRM portal website. Access can be from a phone, tablet, laptop or PC for multiple operating systems. There is no end to the level of control, via the required Color Control GX or Venus GX, from adjusting your MultiPlus to setting a Geofence for hire vehicles and more… Proven reliability The full bridge plus toroidal transformer topology has proven its reliability over many years. The inverter is short circuit proof and protected against overheating, whether due to overload or high ambient temperature.  PowerControl – Dealing with limited generator, shore side or grid power With the Multi Control Panel a maximum generator or shore current can be set. The MultiPlus will then take account of other AC loads and use whatever is extra for charging, thus preventing the generator or shore supply from being overloaded. PowerAssist – Boosting the capacity of shore or generator power Where peak power is so often required only for a limited period, the MultiPlus will make sure that insufficient shore or generator power is immediately compensated for by power from the battery. When the load reduces, the spare power is used to recharge the battery. High start-up power Needed to start high inrush loads such as power converters for LED lamps, halogen lamps or electric tools Programmable relay By default, the programmable relay is set as an alarm relay, i.e. the relay will de-energise in the event of an alarm or a pre-alarm (inverter almost too hot, ripple on the input almost too high, battery voltage almost too low). Brand Victron Energy Manufacturer Part Number PMP482120000 Voltage 48 Transfer Switch (A) 16 Cont. Output Power at 25°C (VA) 1200 Peak Power (W) 2400 Max Efficiency 95% Zero Load Power (W) 10 Charge Current House Battery (A) 13 Charge Current Starter Battery (A) 1 (12V and 24V models only) Battery Temperature Sensor Yes Programmable Relay Yes Remote on-off On/off/charger only Protection Category IP21 Dimensions H406 x W250 x D100mm Weight (kg) 8.2 Warranty 5 Years Country of Manufacture China

Read more less

Brand Victron Energy Manufacturer Part Number SCA000500000 Warranty 5 Years

Read more less

1 UNIT IN STOCK Part No: SOL-RHI-3P5K-HVES-5G-DC Storage Systems - Hybrid Inverter This is the perfect three phase hybrid solution for medium to large houses and business use as well.  Product features 2 x MPPT and 4 DC input at max of 26A 3 x operation modes Self-consumption; time of use; off-grid backup 4 models range from 5KW to 10 KW output as well as backup Supporting Li-ion high voltage batteries ranging from 160 to 600VDC Time of use shifting peak shaving capabilities to grid Intelligent EMS function Supporting three-phase imbalance 24-hour monitor and management system Remotely control and upgrade any selected inverter Supplier Part No: Solis-RHI-3P5K-HVES-5G-DC Weight: 25.1 kg Rated Power: 5,000 W Min PPT Voltage: 160 V Max PPT Voltage: 850 V DC Startup Voltage: 160 V DC Shutdown Voltage: 160 V Max Input Voltage: 1,000 V Max DC Power: 8,000 W Max AC Power (5 Minutes): 5,500 W Surge AC Power (1 Second): 6,000 W Max DC Current: 26 A Max DC Inputs: 2 Has DC Fuses: 0 Connector: MC4   Included Connectors: 4 Euro Efficiency: 97.7 % Transformer: HF MPPT Quantity : 2 Has Integrated DC Switch: Yes Warranty: 5 years Designed by world leading research and development team made by professors and specialists from 8 countries, Solis inverters are praised by clients and customs all over the world due to the high quality and reliability with the feature of ultra wide input voltage, precise MPPT algorithm, and Max. efficiency over 97%, which made Ginlong brand one of the most performance-cost inverters in the world. Data Sheet English

Read more less

Part No: SOL-PRIMEPOWER-109KWH-50KW-NV-C5-M Storage Systems - Hybrid Inverter SolisStorage PrimePower 109kWh/50kW SolisStorage PrimePower -109kWh Standard: Aerosol, explosion relief valve, fire water inlet Optional (Pro-Version here): Combustible gas detector, explosion relief plate, audible and visual alarm SolisCloud: Intelligent remote control, AI optimisation and instant troubleshooting – all in one platform <10 ms switchover from grid-connected to off-grid for uninterrupted power supply or <20 ms with multiple inverters connected in parallel Flexible system expansion, up to 500 kW/6.5 MWh Design & Build Dimensions: 1270 × 2070 × 1357 mm (with inverter) Weight: 1393 kg total-1320 kg (Cabinet) + 73 kg (Inverter) Noise Level: 70 dB at  1 m Ingress Protection: IP55 (cabinet), IP66 (inverter) Anti-Corrosion: C5 Environmental Protection S6-EH3P50K-H (SOL-S6-EH3P50K-H) Attention: an external ATS is needed for connecting more than 6 units in parallel, an ATS from another manufacturer can be used with these Solis units. (Solis external ATS is under development)

Read more less

Part No: SOL-S6-EH3P40K-H Storage Systems - Hybrid Inverter Solis Three Phase High Voltage Energy Storage Inverters Models Features: Allowable PV of up to 80kW, on the 180-1000V MPPT. 4-MPPTs, rated at 40A each, with 2-string inputs each allowing for 8 strings of high power/current PV modules. Supports Grid and Generator AC inputs. Parallel up to 6 x inverters for up to 300kW of back-up load. Battery Charge and Discharge current of up to 140A. UPS transfer time of less than 10ms. 160% surge power for 2s to accommodate inductive loads. Integrated AFCI (DC arc-fault circuit protection) – mitigating fire risks. LCD display and remote firmware upgrades with included S4 Wi-Fi/LAN Stick and Solis Cloud support/monitoring. Solis reliability with 5-year warranty. (extendable to 10/15/20-years) Current transformer ESCT-T50-300A/5A included in product packaging

Read more less

Part No: SOL-S6-EH3P10K-NV-YD-L-UK Storage Systems - Hybrid Inverter Solis Three phase LV Energy Storage Inverter Features: Generator-compatible to extend backup duration during grid power outage Multiple inverters can operate together to form a microgrid Supports dual backup ports for intelligent control of critical and non-critical loads 10 seconds of 200% overload capability Supports a maximum input current of 20A, making it ideal for all high-power PV modules of any brand Ensures excellent power supply stability, keeping the load unaffected by a weak grid or generator supply fluctuations The battery's DC side can handle a maximum charge/discharge current of up to 290A, allowing it to store more surplus energy generated by PV systems Supports Unbalanced and Half-Wave Loads on both the Grid and Backup Port

Read more less

Part No: SOL-S6-EH3P-8.0K-H-UK Storage Systems - Hybrid Inverter Solis S6 8kW 3PH Hybrid Inverter 4 MPPTs, suitable for residential rooftop installations with multiple array orientations Supports Unbalanced and Half-Wave Loads on the Grid Port and on the Backup Port Compatible with multiple brands of battery models giving customers multiple battery options Supports up to 10 units in parallel on Grid and Backup. Suitable for small to medium level commercial energy storage systems Supports pure off grid applications with generator communication support  Multiple working modes to meet different use case scenarios  Controllable and Upgadeable via the SolisCloud App to avoide site visits Up to 16A of MPPT current input to support 182mm/210mm solar panels Supports 1.6 DC:AC ratio to connect more PV capacity to the energy storage system Up to 50A/10kW max charge/discharge rating with industry highest level 10kW of backup loads support capability  UPS level switching time (<10ms) supporting critical loads all the time High PV charge efficiency to prevent excess PV loss Safety protection with integrated AFCI function, which actively detects arc faults in the PV Array Natural convection design without external fans Please note: The inverter is supplied including the S2-WL-ST data logger stick (WiFi & LAN) and a 3PH meter from Eastron

Read more less

Part No: SOL-S6-EH3P-6.0K-H-UK Storage Systems - Hybrid Inverter   Solis S6 6kW 3PH Hybrid Inverter 3 MPPTs, suitable for residential rooftop installations with multiple array orientations Supports Unbalanced and Half-Wave Loads on the Grid Port and on the Backup Port Compatible with multiple brands of battery models giving customers multiple battery options Supports up to 10 units in parallel on Grid and Backup. Suitable for small to medium level commercial energy storage systems Supports pure off grid applications with generator communication support  Multiple working modes to meet different use case scenarios  Controllable and Upgadeable via the SolisCloud App to avoide site visits Up to 16A of MPPT current input to support 182mm/210mm solar panels Supports 1.6 DC:AC ratio to connect more PV capacity to the energy storage system Up to 50A/10kW max charge/discharge rating with industry highest level 10kW of backup loads support capability  UPS level switching time (<10ms) supporting critical loads all the time High PV charge efficiency to prevent excess PV loss Safety protection with integrated AFCI function, which actively detects arc faults in the PV Array Natural convection design without external fans Please note: The inverter is supplied including the S2-WL-ST data logger stick (WiFi & LAN) and a 3PH meter from Eastron

Read more less

Part No: SOL-S5-EH1P3.6K-S-1PH Storage Systems - Hybrid Inverter

Read more less

Part No: SOL-S5-EH1P3K-S-UK Storage Systems - Hybrid Inverter Smart Energy Management AI intelligently manages charging and discharging based on TOU (Time-of-Use) tariffs Seamless integration with VPP and EMS platforms for enhanced energy optimization High Performance 160% PV input capacity to maximize solar energy utilization Flexible & Scalable Compatible with mainstream lithium and lead-acid batteries Simple & Fast Configuration 7-inch LCD screen for an intuitive user experience

Read more less

Part No: SOL-S6-EH3P50K-DY-STACK100-51KWH Storage Systems - Commercial Storage  

Read more less

Part No: SOL-S6-EH3P50K-DY-STACK100-133KWH Storage Systems - Commercial Storage Solis S6 EH3PK and Dyness Stack 100 storage packages

Read more less

Part No: SOL-S6-EH3P40K-DY-STACK100-133KWH Storage Systems - Commercial Storage Solis S6 EH3PK and Dyness Stack 100 storage packages

Read more less

Part No: SOL-S6-EH3P30K-DY-STACK100-30KWH Storage Systems - Commercial Storage Solis S6 EH3PK and Dyness Stack 100 storage packages

Read more less

Part No: SOL-S6-EH3P30K-DY-STACK100-133KWH Storage Systems - Commercial Storage Solis S6 EH3PK and Dyness Stack 100 storage packages

Read more less

Part No: SOL-S6-EH3P20K-DY-STACK100-66KWH Storage Systems - Commercial Storage Solis S6 EH3PK and Dyness Stack 100 storage packages

Read more less

Part No: SOL-S6-EH3P20K-DY-STACK100-41KWH Storage Systems - Commercial Storage

Read more less

Part No: SOL-S6-EH3P15K-DY-STACK100-66KWH Storage Systems - Commercial Storage Solis S6 EH3PK and Dyness Stack 100 storage packages

Read more less